BLACK DECKER LEDUC9-1CCT-ACK Smart Under Cabinet Lighting User Guide

BLACK DECKER LEDUC9-1CCT-ACK Smart Under Cabinet Lighting

Thank You for Choosing Black+Decker

Save this user guide for future reference.Please read this user guide before returning this product for any reason.

Safety Guidelines

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

• DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury and/or property damage.
• WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury and/or property damage.
• CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.
• NOTICE: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.
• WARNING: To reduce the risks associated with impact and hazardous voltage which, if not avoided, could result in death or serious injury and/or property damage:
  • Use indoors and in dry locations only; keep all liquids away from the light
  • Avoid putting the light on an uneven surface to prevent toppling or damage
  • Do not alter or modify the light, ground plug, or polarized plug blades
  • Do not use light with other adapters or voltage supplies
  • Plug the light into grounded, polarized electrical outlet; contact a qualified electrician if a polarized outlet is not available
  • Do not use the light if the power cord or the enclosure is damaged
  • If an extension cord is used, ensure that it is properly rated for your application
  • Do not attempt to disassemble light; product is to be serviced by qualified service personnel only-there are no user serviceable parts inside
  • Always power off and unplug light before cleaning
  • Clean exterior only with a dry, clean cloth; do not immerse light in water to clean
  • Do not use force when adjusting light
  • Do not insert obiects into light
  • If any irregularities are detected during use, turn off the switch and unplug the light

What’s in the Box

For a full list of contents for your kit, please refer to PG. 18.

Plan Your Layout

• This symbol indicates a tip to help during installation.
• This under cabinet lighting was designed for an entirely tool-free application. However, for certain installation options, tools may be required. These will be indicated by the drill symbol.

To find the ideal way to configure your lighting, we recommend planning your layout prior to installation.
Use the steps below to get started.

1. Choose your outlet and control box location
   The control box should be located in the front corner of an easily accessible cabinet and must be within 6′ of a power source.

2. If using a power source located inside of a cabinet, you will need to route the wires through the cabinet walls (See Routing Wires – PG. 7).

3. Based on your plug location, you will either use a split or continuous configuration

   • Split: For layouts where preferred power source is centrally located within cabinets or mounting surfaces (See FIG 1), link light bars and jumper wires using the left and right sides of the control box. (See FIG. 2.1)
   • Continuous: For layouts where preferred power source is on either side of cabinets or mounting surfaces (See FIG 1), link light bars and jumper wires using the left or right side of the control box. (See FIG. 2.2)

4. Lay a light bar on the counter under each cabinet you wish to install a light bar

   • Each 9″ light bar illuminates up to 36″ and is linkable up to 6 bars
   • Each 18″ light bar illuminates up to 42″ and is linkable up to 4 bars
   • Each 24″ light bar illuminates up to 48″ and is linkable up to 3 bars
     Note: If you mix and match bar lengths, check the wattage on each bar and never exceed 24 total watts of power consumption

5. Lay your jumper wires on the counter in between the light bars you will be connecting If you need to jump a sink or stove, use a jumper wire extender to create additional length. If you need additional length, a 108″ Stove & Sink Jumper Wire (LEDJUMP108) is available for purchase.

Routing Wires

For the cleanest installation for your cabinet type, we recommend routing wires using the tips below. Be sure to use the provided wire clips and zip ties as needed.

Frameless Cabinets

• Run connector wires towards the back of cabinet frames to hide the wires and secure with wire clips.

Framed Cabinets

• Loop any excess wire at the back of the cabinet joint. If there is space between two side-by-side cabinets, hide excess wire in the opening.
  1. Run connector wires towards the back of cabinet frames to hide the wires and secure with wire clips.
  2. Loop any excess wire at the back of the cabinet joint. If there is space between two side-by-side cabinets, hide excess wire in the opening.

Running Wires Through Cabinets

1. You can run wires through a cabinet’s walls using a power drill and the bits noted below.
2. You can run wires through a cabinet’s frame using a power drill and the bits noted below.

Jumper Wires: To feed any size jumper wire through a cabinet, use a 1/2″ drill bit
AC Adapter Wire: To feed the AC adapter wire through a cabinet, use a 3/8″ drill bit

How to Install

1. Mount control box in desired location
2. Slide two bar mounting clips onto each light bar
3. Using the provided mounting spacer, mount bar lights and hold in place for 10 seconds
4. Using jumper wires, connect the control box to the first light bars) and light bars to each other.
5. Connect the AC adapter cord to the control box
6. Route and hide wires as desired using wire clips and/or zip ties (See Routing Wires Section PG. 7)
7. Plug in your AC adapter to the power source
   See Routing Jumpers Wires section for tips (PG. 7)

For troubleshooting and support, scan code or visit PureOpticsLED.com/Support.

Connecting to Alexa™

To enable voice and app control, pair the control box to Alexa™* using the following steps. Note: If you are already an Alexa™ user, you may be prompted to connect automatically.

STEP 1: Plug the power cord into the control box. Once connected, the red Wi-Fi light will begin to blink which indicates the device is now in
PAIRING MODE. The red light will blink for approximately five minutes. After the light stops blinkina. the device will no longer be in pairina mode.
STEP 2: Open your Alexa™ App, select Devices, and select the “+” button to “Add Device”
To restart PAIRING MODE, unplug the power cord then reconnect your power cord to your control box.
Note: If you are already an Alexa™* user, you may be prompted to connect automatically.
STEP 3: Select “Light” > “Black+Decker”
STEP 4: Scan QR code on the control box
STEP 5: Your device is now paired. The red light should be off.

For troubleshooting and support, visit PureOpticsLED.com/Support.

How to Use

Alexa” Functionality

Streamline devices and simplify your daily routines by incorporating your under cabinet lighting into Alexa’s native functionality.
Routines
Tie multiple actions into a simple voice command or automate tasks without speaking at all based on schedules, locations, and more.

“Alexa, let’s cook.”

Under cabinet lights power on; natural daylight temperature; full temperature Echo Dot™ plays, “Italian Cooking Music”

“Alexa, good morning.
Under cabinet lights power on; warm light temperature; 20% brightness Coffee maker turns on

Groups
Pair with other smart devices in the room for easy control.

“Alexa, turn on the kitchen.”
Under cabinet lights power on Overhead light turns on

Specifications

Contents

Warranty

Three-Year Limited Warranty
Goods iQ warrants to the original retail purchaser that the product purchased is free from defects in material and workmanship and agrees to repair or replace, at Goods iQ’s option, any defective BLACK+DECKER™ branded under cabinet lighting product (3) years from the date of purchase. Warranty is not transferable. Proof of purchase date required. This warranty covers only damage resulting from defects in material or workmanship; it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse, accident, or repairs attempted or made by other than our national repair center or authorized warranty service centers. You are responsible for the costs of shipping the detective product to Goods iG.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY OF GOODS IQ, AND IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES IN-CLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURCHASE.
GOODS IQ SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Some states and countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and country to country. For information on our warranty claim procedure, please contact us at 855-784-4322.
Latin America: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country specific warranty information contained in the packaging, call the local company, or see the website for warranty information,
To register your new product visit: PureOpticsLED.com/New- Product
For product support visit: PureOpticsLED.com/Support
Support contact number: 1-855-784-4322

This device contains FCC ID: 2AC7Z-ESP32PICOZERO
This device complies with FCC Part 15B. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This device complies with the FCC radiation exposure limits set forth in an uncontrolled environment.
This device should be installed and operated with a minimum distance of 20cm between the equipment and the user’s body.
Manufactured by:
Goods iQ, North Kingstown RI 02852
Under license from The Black and Decker Corporation USA and Canada Only Black+Decker and the Black+Decker logo are trademarks of The Black+Decker Corporation and are used under license. All rights reserved. Product in this box may differ slightly from that pictured. Not all accessories shown in photography are included in this package.
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
A03259
Copyright © 2021 Goods iQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>