PolyScience 110-821 AD Refrigerated Circulating Bath User Guide
- June 10, 2024
- PolyScience
Table of Contents
PolyScience 110-821 AD Refrigerated Circulating Bath
Safety Recommendations
WARNING
- This Cireulating Rath is suitable for use with Class Ill flammable fluide d fire hazard may he present. ” be aware of chemica hazaros that may be associated with the bath fluid used as well as those contained in the materia sate c9rg shoot.
- Explosivp cas mixtures may accumulate if usod win most aseneven Bath in a well vontilated area or heneath a suitable rume hood only a so nov recommences rarn amide cer Technical information in the instruction manual for recommended fluids. Alwavs use fluids thatsatisfy safety. health. and eouioment compatibility
- Use only nonscid bath fluids.
WARNING: When us no hazardous path fluids, the user must attach the following warning labels to the front of the unit so that they are well visible.
- Danger Area. Attention! Observe instructions (operating manual, safety data sheet)
- Carefully read the user information prior to beginning operation. Scope: EU
- Carefully read the user information prior to beginning operation. Scope: NAFTA
WARNING:
- Always connect the power cord on this Circulator to a grounded (3-prong) power outlet. Make certain that the outlet is the same voltage and frequency as your unit. The use of an extension cord is not recommended.
- Never operate the Circulator with a damaged power cord.
- Always turn the Circulator OFF and disconnect mains nower hefore performing any maintenance or service.
WARNING:
- Never operate the Circulator without bath fluid in the reservoir. Periodically check the reservoir to ensure that the liguid depth is within acceptable levels. Alwaysrefill the reservoir using the same bath fluid type that is already in the reservoir. Bath oil must not contain any water contaminants and should be preheated to the actual bath temperature before adding as there is an explosion hazard at high temperatures.
- – Always drain all fluid from the reservoir before moving or lifting your Circulator. Be sure to follow your organization’s procedures and practices regarding the safe lifting and relocation of heavy obiects.
WARNING: It is the user’s responsibility to properly decontaminate the
unit in the event hazardous materials are spilled on exterior or interior
surfaces. Consult manufacturer if there is any doubt regarding the
compatibility of decontamination or cleaning agents.
WARNING: Read the safety data sheet for the bath fluid being used before
filling the reservoir. Always use fluids that satisfy safety, health, and
equipment compatibility requirements.
WARNING: The use of an extension cord is not recommended.
WARNING:
- Always allow the bath fluid to cool to ambient temperature before draining.
- The reservoir cover, top deck, and/or external pump connections may become hot with continuous use. Exercise caution when touching these parts.
- Always keep within the 85°C maximum operating temperature limit if using a polycarbonate tank.
General Safety Symbols
- This symbol alerts you to a wide range of potential dangers.
- This symbol advises you of danger from electricity or electric shock.
- The symbol indicates that a hot surface may be present.
- This svmbol marks information that is particularly important.
- This svmbol indicates alternating current.
- These symbols on the Power Switch/Circuit Breaker indicate that they olace the main power supoly ON/OFF.
- This symbol on the Power Key indicates that it places the unit in a standby mode. It DOES NOT fully disconnect the unit from the power supply
- Read all instructions pertaining to safety, setup, and operation. Proper operation and maintenance is the user’s responsibility.
Circulating Bath Quick Start Guide
This guide offers the quickest way to install and begin operating our Circulating Bath. It provides only the details necessary to get you us and running. Please refer to tho instruction manual contained on tho Docoureo Diek that camo with your circulator for full operational information
- Fill reservoir with fluid
- Connect te scounded sleete.
- Theo Msine Bowor ON
- Turn Controller power ON.
- Select language.
- Press the Menu key until the current language is displayed.
- To change, touch the scroll bar until the desired language is displayed.
- To accept, press operational display. , or allow the LCD to return to the main operational display.
- Adjust the Safety Set temperature
- Press Menu key E until SAFETY appears.
- Adjust safety set temperature.
- Press to return to the main operational screen.
- Set temperature set point.
- Press the SET key
- Touch the scroll bar until the desired set point temperature is displayed.
- To accept, press or allow the LCD to return to the main operational display.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>