PCE Instruments PCE-T 240 Handheld Tachometer User Manual
- June 10, 2024
- PCE Instruments
Table of Contents
PCE Instruments PCE-T 240 Handheld Tachometer
User manuals in various languages (français, italiano, español, português, nederlands, türk, polski, русский, 中文) can be found by using our product search on: www.pce-instruments.com.
Safety notes
Please read this manual carefully and completely before you use the device for the first time. The device may only be used by qualified personnel and repaired by PCE Instruments personnel. Damage or injuries caused by non- observance of the manual are excluded from our liability and not covered by our warranty.
- The device must only be used as described in this instruction manual. If used otherwise, this can cause dangerous situations for the user and damage to the meter.
- The instrument may only be used if the environmental conditions (temperature, relative humidity, …) are within the ranges stated in the technical specifications. Do not expose the device to extreme temperatures, direct sunlight, extreme humidity or moisture.
- Do not expose the device to shocks or strong vibrations.
- The case should only be opened by qualified PCE Instruments personnel.
- Never use the instrument when your hands are wet.
- You must not make any technical changes to the device.
- The appliance should only be cleaned with a damp cloth. Use only pH-neutral cleaner, no abrasives or solvents.
- The device must only be used with accessories from PCE Instruments or equivalent.
- Before each use, inspect the case for visible damage. If any damage is visible, do not use the device.
- Do not use the instrument in explosive atmospheres.
- The measurement range as stated in the specifications must not be exceeded under any circumstances.
- Non-observance of the safety notes can cause damage to the device and injuries to the user.
We do not assume liability for printing errors or any other mistakes in this
manual.
We expressly point to our general guarantee terms which can be found in our
general terms of business.
Specifications
Optical measurement
Measurement range| 5 … 99,999 RPM
Resolution| 0.5 RPM (<1,000 RPM)
1 RPM (>1,000 RPM)
Accuracy| ±(0.05 % of rdg. + 1 digit)
Detection distance| 50 … 150 mm, 2 … 6 inch (typical)
maximum 300 mm, 12 inch (depending on the ambient lighting)
Contact measurement
Measurement range| 0.5 … 19,999 RPM
Resolution| 0.5 RPM (<1,000 RPM)
1 RPM (≥1,000 RPM)
Accuracy| ±(0.05 % of rdg. + 1 digit)
Measurement range| 0.05 … 1,999.9 m/min
Resolution| 0.05 m/min (<100 m/min)
0.1 m/min (≥100 m/min)
Accuracy| ±(0.5 % of rdg. + 1 digit)
Measurement range| 0.2 … 6,561.4 ft/min
Resolution| 0.1 ft/min (<1,000 ft/min) 1 ft/min (≥1,000 ft/min)
Accuracy| ±(0.5 % of rdg. + 1 digit)
Measurement range| 2.0…. 78736.2 inch/min
Resolution| 0.1 inch/min (<1,000 inch/min) 1 inch/min (≥1,000 inch/min)
Accuracy| ±(0.5 % of rdg. + 1 digit)
Stroboscope
Measurement range| 100 … 99,990 RPM/FPM
Resolution| 0.1 RPM (<1,000 PRM)
1 RPM (1,000 … 30,000 RPM)
5 RPM (30,000 … 50,000 RPM)
10 RPM (50,000 … 99,999 RPM)
Accuracy| ±(0.1 % of rdg. + 2 digits)
LED| three red LEDs
Temperature (type K)
Measurement range| -50.0…. 1300.0 °C
Resolution| 0.1 °C
Accuracy| ±(0.4 % of rdg. +0.5 °C)
Measurement range| -100.0….. 50.1 °C
Resolution| 0.1 °C
Accuracy| ±(0.4 % of rdg. +0.5 °C)
Measurement range| -58.0…. 2372.0 °F
Resolution| 0.1 °F
Accuracy| ±(0.4 % of rdg. +1 °F)
Measurement range| -148.0 … -58.1 … °F
Resolution| 0.1 °F
Accuracy| ±(0.4 % of rdg. +1.8 °F)
Temperature (PT1000)
Measurement range| -10.0 … 70.0 °C, 414.0… 158.0 °F
Resolution| 0.1 °C, 0.1 °F
Accuracy| ±1.2 °C, ±2.2 °F
Further specifications
Display| LC display, 43 x 33 mm, 5 digits
Memory| highest and lowest measured value
Power supply (mains adaptor)| 9 V DC, 100 mA
Power supply (battery)| 4 x 1.5 V AA batteries
Power consumption| Ø42 mA
Automatic power off| after 10 minutes of inactivity
Interface| RS232
Environmental conditions| 0 … 50 °C, 32 … 122 °F,
<80 % RH, (non-condensing); magnetic field
<3 V/M, <30 MHz
Dimensions| 207 x 67 x 39 mm, 8.15 x 2.63 x 15.3 in
Weight|
230 g, 0.5 lb (without batteries)
Delivery scope
- 1 x PCE-T 240 handheld tachometer
- 1 x measuring tip (outer cone)
- 1 x hollow measuring tip (inner cone)
- 1 x measuring wheel
- 1 x reflective tape
- 1 x carrying case
- 4 x 1.5 V AA battery
- 1 x user manual
Device description
| No. | Description |
|---|---|
| 1 | Display |
| 2 | On and off key |
| 3 | Hold key, arrow up key |
| 4 | REC key, double key |
| 5 | UNIT key, arrow down key |
| 6 | Function key |
| 7 | Measuring tip (outer cone) |
| 8 | Surface speed adaptor |
| 9 | Hollow measuring tip (inner cone) |
| 10 | RS232 interface |
| 11 | PT1000 temperature sensor connection |
| 12 | Thermocouple connection K-type |
| 13 | Photo tripod connection |
| 14 | Battery compartment cover |
| 15 | Reflective tape |
| 16 | White LED for optical speed measurement |
| 17 | Strobe light with red LEDs |
| 18 | Indicator for one revolution |
| 19 | Power supply connection |
Making a measurement
First switch on the meter by pressing and holding the on/off key. To switch
off the meter, you must also keep this key pressed. As soon as the meter is
switched on, the measurement starts directly with the last measurement
function used.
To select between the individual measuring functions, press the function key
repeatedly.
The following functions are available:
| Display when switching | Function |
|---|---|
| Scope | Stroboscope |
| type | Temperature measurement with K-type thermocouple |
| Pt | Temperature measurement with a PT 1000 temperature sensor |
| Photo | Optical speed measurement |
| touch | Contact speed and velocity measurement |
Stroboscope
To make a measurement with the stroboscope function, select the “Scope” function. Align the LEDs in the direction of the test object. Now set the speed using the arrow keys. To double or halve the rotation speed, hold down the double button and then use the arrow keys.
Optical speed measurement
To make an optical speed measurement, select the “Photo” function. Stick a 1 x
1 cm piece of reflective tape onto the test object. Now switch on the test
object and direct the light cone so that it shines on the reflective tape. The
speed of rotation is measured. Next to the measured value, an indicator
flashes once briefly as soon as the reflective tape has been recognised.
Contact revolution measurement
To make a contact revolution measurement, select the “touch” function. Plug
the desired adaptor onto the meter. Select the unit “RPM” with the UNIT key.
Now carry out the measurement on the test object.
Note:
The wheel attachment is only intended for speed measurement.
Contacting speed measurement
To make a contact speed measurement, select the “touch” function. Place the
wheel attachment on the meter. Press the UNIT key repeatedly until the desired
unit is displayed. You can then carry out the speed measurement.
Temperature measurement with a thermocouple
To perform a temperature measurement, select the “type” function. Insert a
K-type thermocouple into the meter. The measured value appears on the display.
Temperature measurement with a PT 1000 temperature sensor
To carry out a temperature measurement, select the “pt” function. Insert a PT
1000 resistance temperature probe into the meter. The measured value is
displayed directly.
Freezing measured value (HOLD)
To freeze the displayed reading, press the Hold key. “HOLD” appears on the
display. To resume the measurement, press the Hold key again.
Highest and lowest measured value (REC)
Press the REC key. “REC” is displayed on the screen. To view the highest and
lowest readings, press the REC key repeatedly. Press and hold the REC key to
disable this function.
As soon as this function has been switched off, the values are reset.
Settings
Automatic power-off
To enable or disable the automatic power off function, press and hold the
function key for at least 5 seconds. The arrow keys can now be used to enable
or disable automatic power off. Press the REC key to accept the setting. Use
the on/off key to return to measurement mode.
Note : The “HOLD” and “REC” functions must be switched off.
Changing the temperature unit
Press and hold the function key for about 5 seconds. Then press the
function key again to change the temperature unit. The temperature unit can
now be changed with the arrow keys. Press the REC key to accept the setting.
Press the ON/OFF key to return to measurement mode.
Note:
The “HOLD” and “REC” functions must be switched off.
When the function is switched off, the values are reset.
Replacing the batteries
To insert or replace the batteries, first switch off the meter. Then open the battery compartment and replace the batteries. Ensure correct polarity of the batteries. Use four 1.5 V AA batteries.
RS232 interface
The unit has a serial RS232 interface with a 3.5 mm output. The data output is
via a 16-digit stream which can be used for your specific applications.
An RS232 guide with the following connection is required to connect the meter
to a serial PC output.
The 16-digit streams are displayed as follows:
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
Each digit indicates the following status
RS232 format : 9600, N, 8, 1
Contact
If you have any questions, suggestions or technical problems, please do not hesitate to contact us. You will find the relevant contact information at the end of this user manual.
Disposal
- For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament applies. Due to the contained pollutants, batteries must not be disposed of as household waste. They must be given to collection points designed for that purpose.
- In order to comply with the EU directive 2012/19/EU we take our devices back. We either re-use them or give them to a recycling company which disposes of the devices in line with law.
- For countries outside the EU, batteries and devices should be disposed of in accordance with your local waste regulations.
- If you have any questions, please contact PCE Instruments
PCE Instruments contact information
Germany
PCE Deutschland GmbH Im Langel 26 D-59872 Meschede Deutschland
Tel.: +49 (0) 2903 976 99 0
Fax : +49 (0) 2903 976 99 29 info@pce-instruments.com
www.pce-instruments.com/deutsch
United Kingdom
PCE Instruments UK Ltd Unit 11 Southpoint Business Park Ensign Way,
Southampton Hampshire United Kingdom, SO31 4RF
Tel : +44 (0) 2380 98703 0
Fax : +44 (0) 2380 98703 9
info@pce-instruments.co.uk www.pce-
instruments.com/english
The Netherlands
PCE Brookhuis B.V. Institutenweg 15 7521 PH Enschede Nederland
Telefoon : +31 (0)53 737 01 92
info@pcebenelux.nl
www.pce-instruments.com/dutch
France
PCE Instruments France EURL 23, rue de Strasbourg 67250 Soultz-Sous-Forets
France
Téléphone : +33 (0) 972 3537 17
Numéro de fax: +33 (0) 972 3537 18 info@pce-france.fr
www.pce-instruments.com/french
Italy
PCE Italia s.r.l. Via Pesciatina 878 / B-Interno 6 55010 Loc. Gragnano
Capannori (Lucca) Italia
Telefono : +39 0583 975 114
Fax : +39 0583 974 824
info@pce-italia.it
www.pce-instruments.com/italiano
United States of America
PCE Americas Inc. 1201 Jupiter Park Drive, Suite 8 Jupiter / Palm Beach 33458
FL USA
Tel : +1 561-320-9162
Fax : +1 561-320-9176
info@pce-americas.com
www.pce-instruments.com/us
Spain
PCE Ibérica S.L. Calle Mayor, 53 02500 Tobarra (Albacete) España
Tel. : +34 967 543 548
Fax : +34 967 543 542
info@pce-iberica.es
www.pce-instruments.com/espanol
Turkey
PCE Teknik Cihazları Ltd.Şti. Halkalı Merkez Mah. Pehlivan Sok. No.6/C 34303
Küçükçekmece – İstanbul Türkiye
Tel : 0212 471 11 47
Faks : 0212 705 53 93
info@pce-cihazlari.com.tr
www.pce-instruments.com/turkish
Denmark
PCE Instruments Denmark ApS Birk Centerpark 40 7400 Herning Denmark
References
- France.fr : Explore France and its wonders - Explore France
- iberica.es
- Make an offer on the domain instruments.co.uk - Domains.co.uk
- Computer Instruments | Home
- Discover Italy: Official Tourism Website - Italia.it
- pce-instruments.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>