BLACK DECKER BDX1006 Ratchet Strap Instruction Manual

: June 10, 2024
: Black Decker

Table of Contents

BLACK DECKER BDX1006 Ratchet Strap
Product Information
Product Usage Instructions
WORK STRENGTH FORCE DE TRAVAIL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BLACK DECKER BDX1006 Ratchet Strap

Product Information

The Ratchet Straps are a product of BCS International, located at 1510 Brookfield Ave. Green Bay, WI 54313. The product is designed to provide a work strength force de travail fuerza de trabajo of 500 LB. / 226.8 KG. The product features the Black & Decker logo and trademark, which are used under license. The product can be operated using the ratchet mechanism, which allows for easy tightening and loosening of the webbing. The product comes with a warranty covered by BCS International.

Product Usage Instructions

Before using the Ratchet Straps, it is important to read and understand all instructions and warnings provided in the user manual. Failure to comply with these instructions may cause damage to the product, personal property, and/or personal injury.

With the ratchet closed, thread the webbing from the center spool through the ratchet reel.
Pull the webbing through, removing any slack.
To tighten, raise and lower the ratchet handle. Do not overtighten. Make sure to have a minimum of 2 full wraps of webbing
around the reel.
To release, lift the release bar and pull the webbing to release any tension.
To lock, keep the ratchet in a closed position.
To unlock, pull the release bar until the ratchet is completely flat and open.
Grab the webbing and pull to release.

It is important to note that the product should be used within its specified work strength force de travail fuerza de trabajo of 500 LB. / 226.8 KG. Overtightening may cause damage to the product and/or personal injury. The product warranty is covered by BCS International.

WORK STRENGTH FORCE DE TRAVAIL

Black & Decker and the Black & Decker Logo are trademarks of Stanley Black & Decker, Inc. or one of its aliates, and are used under license.

www.BLACKANDDECKERSTRAPS.com
BLACKANDDECKER.com

WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS AND FULLY COMPLY WITH ALL WARNINGS.
FAILURE TO DO SO MAY RESULT IN DAMAGE TO THIS PRODUCT, PERSONAL PROPERTY AND/OR PERSONAL INJURY.

With ratchet closed, thread webbing from the center spool through the ratchet reel.
Pull webbing through, removing the slack.
Close up view Release the ratchet by lifting the release bar. To tighten, raise and lower ratchet handle; do not overtighten. (Make sure to have a minimum of 2 full wraps of webbing around the reel.)
Keep ratchet in closed position to lock.

TO RELEASE

To unlock, pull the release bar Release bar until the ratchet is completely ﬂat and open.
To unlock, pull the release bar Release bar until the ratchet is completely ﬂat and open.

WARNING

ANSI approved eye protection to be worn at all times during use.
DO NOT use strap that has fraying, wear, broken or worn stitching, tears, cuts or defective hardware. If the strap is damaged DO NOT use it and discard it.
DO NOT exceed the working load limit of the strap; taking into account the strap, the load, the vehicle anchor points, strap conﬁguration and angle, etc.
DO NOT over-tighten straps.
NEVER stand in direct path of a tension loaded strap.
Maintain and store straps properly. Straps should be protected from mechanical, chemical and environmental damage.
ALWAYS protect straps in contact with edges, corners, protrusions, or abrasive surfaces with materials of sufficient strength, thickness and construction to prevent damage.
Manufacturer is not liable for accidents caused by material deterioration or improper use.
For more information on the manufacturer’s warranty, visit www.blackanddeckerstraps.com, or contact BCS at.

877-257-8727 or email info@blackanddeckerstraps.com
The warranty of this product is covered by
BCS International.

WARNING
CANCER AND REPRODUCTIVE HARM
www.P65Warnings.ca.gov