Surenoo STP0350A3-320480 Series TFT LCD Panel User Manual

Model No.: STP0350A3-320480
STP0350A3-320480 Series
TFT LCD PANEL USER MANUAL
IPS Mode

STP0350A3-320480 Series TFT LCD Panel

Please dick the following image to buy the sample

https://www.aliexpress.com/item/4000549728489.html

General Description

CTP: GT911

Mechanical Specification

Mechanical Dimension (With RTP)

3.1 LCD Panel

NOTES:

1. DISPLAY TYPE:TFT
2. OPERATING TEMP: -20° C“70° C
3. STORAGE TEMP: —30° C“80° C
4. 1CD DRIVER: COG(IC:ST7796U);
5. BACKLIGHT:
6. CHIP-WHITE LED(Paralell)
7. GENERAL TOLERANCE: 0. 20
8. ROHS

3.2 Touch Screen

Note: CTP driver. GT911

SHENZHEN SURE NO0 TECHNOLOGY CO., LTD.|
---|---
| CTP2063A-GFF3.5
| | |
UNMRKED TOLERANCE:±0.20 mm| 2021.09.06| | | | 1 OF 1

3.3 LCD with Capacitive Touch Screen

NOTES :

1. DISPLAY TYPE:TFT
2. OPERATING TEMP: -20° C“70° C
3. STORAGE TEMP: -30° C780° C
4. LCD DRIVER: COG(IC:ST7796U);
5. BACKLIGHT: 8 CHIP-WHITE LED(Paralell)
6. GENERAL TOLERANCE : +0. 20
7. ROHS

Electrical Maximum Ratings

Brightness characteristic & Power dissipation

| 3.| 3.| 3.| V
LED module current| km| –| 120| –| mA
LCD Surface Luminance| Ls| 360| 380| | Cern’
LCM Surface brightness uniform| LD| 80| –| –| %
LCD power dissipation| PLOD| –| 0.462| –| W

NOTE: PLCD-VDD*(I LED+I LCD)

Module Function Description

DCX=” 1′ : display data or parameter.
DCX=. 0′ : command data| –
11| WILX/SPI SCL| – Write enable in MCU parallel interface.
– In SPI mode, this pin is used as SCL.| –
12| RDX| -Read enable in 8080 MCU parallel interface.
-If not used please fix this pin at VDDI or GYP.| –
---|---|---|---
13| SPI SDI/SDA| – SPI interface input pin.
– The data is latched on the rising edge of the SCL signal.
– If not used, please fix this pin at VDDI or DGND level.| –
1 I| SPI SDO| -SPI interface output pin.
-The data is output on the falling edge of the SCL signal. -If not used let this pin open.|
15| RESET| -This signal will reset the device and it must be applied to properly initialize the chip.
-Signal is active low.|
16| GND| Ground|
17-24| DBO-DB7| MCU parallel interface data bus.| –
25-32| DB8-DB15| MCU parallel interface data bus.| –
33| LED-A| Anode of Backlight (2. 9V-3. 3V Typical:3. 1V)|
34-36| LED-K| Cathode of Backlight|
37| GND| Ground|
38| IMO| -The MCU interface mode select. ( MCU| IM2| IM1| IMC| MCU interface Mode| Data pin
---|---|---|---|---
0| 1| 0| 80-16bit parole I/F| DB15-080
0| 1| 1| 80-8bit parallel I/F| DB7-DBO
1| 0| 1| 3-line 9bit serial I/F| SDA: in SDO: out
1| 1| 1| 4-line 8bit serial I/F| SDA: in SDO: out
–
39| IM1|
40| 1M2| –

6.2 CTP Interface Description

Response time& Contrast ratio

Brightness on the “black” state

Viewing Angle

Reliability Trial

Function In Room Temperature Are Allowable
-)| Low Temperature Non-Operating Test| -30°C120Hrs
3| High Temperature/Humidity Non Operating Test| 60°C 90%RH120Hrs
4| High Temperature Operating Test| 70°C 72Hrs
5| Low Temperature Operating Test| -20°C 72Hrs
6| Thermal Shock Test| -20 °C (30Min) v 70 °C
(30Min) 10CYCLES

Inspection standards

10.1Glass defect

1. b‘.1/3Pin width(non bonding area) (Accept ] 2)bonding area‘.0. 5mm (Accept]| A: Length, b: Width
   4| Pin-side ,conductive area damaged
   (minor defect)| (a c: disregards) b*.c1/3of effective length for bonding electrode (Accept]| a: length,
   b: Width,
   c: Thickness
   5| Pin-side,non-conductive area damaged (minor defect)| 1)Damage area don’t touch the ITO (Including contraposition mark, except scribing mark)
   [Accept] 2)C<T b —– BM 1/3of width [Accept] 3)c=T
   b not touch the seal glue [Accept] 4)a disregards| a: Length,
   b: Width
   c: Thickness

6| Non-pin-side damage (minor defect)| c<T 1)b exceeds 1/3Bm [Reject ] c=T
b not touch the seal glue [Reject]| c: Thickness
b: width of damage
---|---|---|---

2LCD appearance defect(View area)

cratch, polarizer scratch/folded
(minor defect)| Specification| Allowable| notel  : L: Length, W: Width
note2: disregard if out of AA

Wg0 03 mm| disregard
0.03mm<W g O. 05mm; L g 3. Omm| 2
0.05mm<W g0. 1mm; L ‘.– 3. Omni| 1
W>0.1mm;L>3.0min| 0
N| Polarizer bubble, concave and convex
(minor defect)| 4) g 0.2mm| disregard| notel: 4) = (L+W) /2, L :Length,
W :Width
note2:disregard if out of AA
0.2mm< 4) g O. 3mm| 2
0.3mm< 4) g 0. 5mm| 1
0 5mm< 4)| 0
3| Black dots, dirty dots,
impurities, eye winker
(minor defect)| 4) g 0.15mm| disregard| note2:disregard if out of AA
0.15mm< 4) g 0. 25mm| 2
0.25mm< 4) g 0. 3mm| 1
0 3mm< 4)| 0
4| Polarizes prick
(minor defect)| 4) g 0.1mm| disregard| notel: 4) = (L+W) /2, L=Length,
W=Width
note2:the distance between two dots>5nun
0.1mm<4 ‘ 0. 25mm| 3
4) >O. 25mm| 0

Package Method

MECARD:TEL:0086-17820607849;URL:
http://www.surenoo.com
EMAIL:info@surenoo.com
N:Potter Hao; ORG: Surenoo Technology;
https://wa.me/qr/4GGOIDYZ2PXXN1
http://qr.kakao.com/talk/THom9tzJN5OMzvx1vTL1V.LvnEc-
https://line.me/ti/p/oas8BmVLVd
Shenzhen Surenoo Technology Co.,Ltd.
www.surenoo.com
Skype: Surenoo365
Reference Controller Datasheet
TFT LCD Panel Selection Guide
ST7796S
GT911

References

• Surenoo Display

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>