V-TAC VT-2414 300W LED Sync Dimmer with RF 14B Remote Control Instruction Manual
- June 4, 2024
- V TAC
Table of Contents
V-TAC VT-2414 300W LED Sync Dimmer with RF 14B Remote Control
TECHNICAL DATA
| Model | VT-2414 |
|---|---|
| Output | 1 Channel |
| Output Current | 25A (MAX) |
| Output Power | 300W |
| Supply Voltage | DC: 12V~24V |
INTRODUCTION & WARRANTY
Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at their best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours of Daily operation. Usage of the product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.
WARNING
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a certified person.
This marking indicates that this product should not be disposed of with other household wastes.
PRODUCT DESCRIPTION
The LED Sync Dimmer adopts the most advanced PWM (Pulse Width Modulation) digital dimming technology, especially designed for single-color led strips. For instance, point source of the light, flexible light strips, led modules, led strings, and so on. Belong to low-voltage DC power input and output with two interfaces, including V+ is the positive interface, the other one for the negative interface. Meanwhile, you can turn on/off, adjust brightness for different lighting effects through RF 14keys remote control. In addition, It is convenient to useRJ45 connector to connect the multiple controllers together, and achieve the synchronization function of thousands meters led strips. In theory, they can be connected numerous.
DIRECTION OF USE
- Connect the load wire at first, followed by the power wire; Please ensure a short circuit cannot occur between wires before turning on the power
- Adopts RF remote technology, 14 buttons in total.
REMOTE CONTROLS
| Name | Description |
|---|
Set button
| For sering the night light and matching code with receiver. Under night light mode, press “Set button” and hold on for 10 seconds will go into the night light serving.
Press the set button again to save the serving and quit out.
ON| Turn on
OFF| Turn off
Brightness +| The brightness will add 1 level after each time press. Long-
press can get fast
adjusting.
Brightness –| The brightness will reduce 1 level after each time press. Long- press can get fast
adjusting.
Hot brightness key +| 4 levels brightness (10%、30%、70%、100% ) hot selection
key, lights will go to next one after each pressing.
Hot brightness key –| 4 levels brightness (10%、30%、70%、100% ) hot selection
key, lights will go to last one after each pressing.
Mode key| 3 modes in total: 100% static, flash, breathe
Night light
| Press the button go to night light mode（night light Setting ：Under night
light mode, press “Set button” and hold on for 10 seconds will go into the
night light serving, press the left button to down the brightness, press the
right button to up the brightness. Adjustable range: 1%-10%.）
Speed +| Add the speed of dynamic mode. Long-press can get fast adjusting.
Speed –| Reduce the speed of dynamic mode. Long-press can get fast adjusting.
Delay button| The light will be delay off in 30 seconds.
Tips: Receiver can be controlled by any one the same remote as factory default; RF BT remote control delivered with unique RF code as factory default; if unique-control is needed, please match the code before installation and using.
MATCHING CODE OPERATION
If unique-control or new-coded-remote is needed, pairing the remote and the receiver as below operation instruction before using:
- Step 1: Press the key “set” and hold on, power on the controller, the load LEDs will be 50% brightness white as responding.
- Step 2: Continuously press the key “Mode key“3 times within 5 seconds after step 1,the brightness of LEDs will change from 25% -10% as responding.
- Code learning successfully, the LEDs will be back to the status before the power is off, and the receiver only can be controlled by the remote.
- If not, please re-operate from steps 1 to 2.
CLEAR CODE OPERATION
Back to factory default, wall panel can be controlled by any one the same
remote control.
- Step 1: Press key “set” and hold on, power on the controller, the load LEDs will be 50% brightness white as responding.
- Step 2: Continuously to press the “Delay button“ 3 times within 5 seconds after step 1,the brightness of LEDs will change from 25% -10% as responding.
- Code clearing successfully, the LEDs will be back to the status before the power is off, and the receiver can be controlled by any remote control(any one the same remote control can be used to clear the code).
- If not, please re-operate from step 1 to 2.
TYPICAL APPLICATIONS
POWER AND LED’S CONNECTION DIAGRAM:
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>