VERKADA AD33 Door Reader Installation Guide
- June 11, 2024
- Verkada
Table of Contents
Install Guide
AD33 Door Reader
Document
Document Details
V1.1 (20220321)
(V1.0 first published 20220315)
AD33 Door Reader
Firmware
Firmware version can be verified on Verkade Command
command.verkada.com.
Introduction
AD33 Technical Specifications
| Mullion Dimensions | 95 x 45 x 21mm (3.7 x 2.9 x .82in) |
|---|---|
| Single Gang Dimensions | 120 x 80 x 21mm (4.7 x 3.1 x .82in) |
| Credential Compatibility | Bluetooth LE, RFID (LF and HF) |
| Low Frequency (125 kHz) | HID Proxy II 26-Bit (H10301), 37–Bit Wiegand |
HID H10304, 37–Bit
Wiegand HID H10302, HID 35–Bit Corporate 1000
High Frequency (13 MHz)| MI Fare / Desire (CSN), NFC
Ratings| IP65, IK08
Operating Temperature| -40° to 65°C (–40° to 149°F)
Controller Compatibility| Requires Verkade Access Control Unit (AC41,
AC42, or AC62)
Power Consumption| 12V, 300mA max
Compliance| FCC, CE, UL 294, UL 62368–1/CSA C22.2,
CAN/ULC–60839–11–1:2016, NDAA, TELEC
Included Accessories| Single gang mounting plate, Mullion mounting
plate, T8
Security Torx hand tool, 2 Wall mount screws, 2 M3 Machine screws
Mounting Options| Unit ships with both standard Single Gang mounting
plate and Mullion mounting plate
What’s in the box
What you’ll need
- A working internet connection
- A smartphone or laptop
- A #2 Phillips driver (screwdriver or power drill)
- 1/8 inch (3mm) drill bit for pilot holes
- 1/2 inch (12.7mm) drill bit, or larger, for routing cable through wall
Door Reader overview
LED Behavior
| Static status LED
Powered on and
connected to the ACU.| | Green feedback LED
Has successfully processed a
user scan and granted access.
---|---|---|---
| Cascading status LED
Powered on but cannot connect to the ACU.| | Red feedback LED
Has successfully processed a user scan and denied access.
Installation
Mounting option 1: Single gang
-
Loosen the security screw until the entire screwhead is exposed and remove the AD33 Door
Reader from the mullion mount. -
Route the building-side cable through the opening in the single gang mount. Secure the single gang mount to the junction box using the 2 M3 machine screws.
-
Connect the wires using the diagram or the table on the back of the AD33 Door Reader as reference.
-
Insert the AD33 Door Reader into the single gang mount and secure using the T8 security screw and provided T8 Security
Torx hand tool.
Mounting option 2: Mullion or wall
-
Loosen the security screw and remove the AD33 Door Reader from the mullion mount.
-
Using the mullion mount as your template, mark and drill two ⅛ inch (3mm) pilot holes at the top and bottom. Drill a 1/2 inch (12.7mm) center hole for cable routing.
-
Route building-side cable through the center hole and the circular opening in the mullion mount. Secure the mullion mount to the mullion using the 2 M3 machine screws. If you are installing on a wall, use the 2 provided wall mount screws instead.
-
Connect the wires using the diagram above or the table on the back of the AD33 Door Reader as reference.
-
Insert the AD33 Door Reader into the mullion mount and secure using the T8 security screw and provided T8 Security Torx hand tool.
|
---|---
Appendix
AD33 Compliance
FCC
Statement| This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement: The product comply with the FCC portable RF
exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power
if such function is available.
---|---
IC
Statement| This device complies with ISED’s license-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Radiation Exposure Statement: The product comply with the Canada portable
RF exposure limit set forth for an uncontrolled environment and are safe for
intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power
if such function is available.
Support
Thank you for purchasing this Verkada product. If for any reason things don’t
work right, or you need assistance, please contact us immediately.
verkada.com/support
Sincerely, The Verkade Team
Verkade Inc. 405 E 4th Ave, San Mateo, CA 94401
sales@verkada.com
All specifications are subject to change without notice
Copyright © Verkade Inc. All rights reserved.