AV LINK MaitreView 4KLite Multi-Window Video Processor User Guide

: June 11, 2024
: Av:link

Table of Contents

AV LINK MaitreView 4KLite Multi-Window Video Processor
BEFORE YOU BEGIN
CONTACT INFORMATION
OVERVIEW
APPLICATIONS
FEATURES
PANEL DESCRIPTION
- Front Panel
Led Indicators
Remote Control
CONNECTION DIAGRAM
PACKAGE CONTENTS
INSTALLATION
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AV LINK MaitreView 4KLite Multi-Window Video Processor

AV LINK MaitreView 4KLite Multi-Window productt

BEFORE YOU BEGIN

Follow all instructions marked on the device during use.
Provide proper ventilation and air circulation and do not use near water.
It is better to keep it in a dry environment.
Place the device on a stable surface (for example cart, stand, table, etc.).
The system should be installed indoors only. Install either on a sturdy rack or desk in a well-ventilated place.
Make sure the rack is level and stable before extending a device from the rack if necessary.
Make sure all equipment is installed on the rack including power strips and other electrical connectors are properly grounded.
Only use the power cord supported with the device.
Do not use liquid or aerosol cleaners to clean the device.
Always unplug the power to the device before cleaning.
Unplug the power cord during lightning or after a prolonged period of non-use to avoid damage to the equipment.
Do not stand on any device while installing the device to the rack.
Do not attempt to maintain the device by yourself, any faults, please contact your vendor.
Save this manual properly for future reference.

COPYRIGHT AND TRADEMARKS
All rights reserved by AV LINK GROUP LTD. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. They will be incorporated in subsequent editions. The product manufacturer may make improvements and changes in the product described in this document at any time.
(Note: If there is any discrepancy with the latest version, please refer official website as the primary source of Information)

CONTACT INFORMATION

AV LINK GROUP LTD.
Headquarters: 13F.-1, No. 2, Jian 8th Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) TEL: 886-2-8226-2268
FAX: 886-2-8226-2269
E-mail: sales@cctch.com.tw
Website: https://avlinksystem.com
For Warranty:
Please follow the warranty policy according to AV LINK’s local official distributor; during the warranty period, it is recommended to keep your proof of purchase, accessories, and packaging in place.

OVERVIEW

Thank you for purchasing AV LINK’s Multi-window Video Processor: MaitreView™ 4KLite is a true 4K HDMI Video Processor, that can generate powerful uncompressed 4K video algorithms driving on FPGA, it allows up to 4 HDMI inputs and output on 2 HDMI output, where all inputs and output support to uncompressed 4K/60Hz 4:4:4.
It can switch up to 6 default layouts and single view modes, it uses seamless switching technology, which independent layouts can display on 2 outputs. It can operate by front panel, remote control and also by Web GUI and Remote control APP (Android tablet & iPad) control. This quick start guide will take you through the necessary steps to get started with MaitreView™ 4KLite.

APPLICATIONS

MaitreView™ 4KLite is a powerful device that can be used in:

Corporate
Design house
Education
Entertainment
Esport
Fashion
Government
- lth Care
House of worship
Retail

And any application which requires seamless switching and powerful video processing.

FEATURES

Unparalleled video processing engine
Uncompressed 4K/60Hz, 4:4:4
6 layouts
Independent layouts on 2 outputs
Seamless switching
Front panel display (LCM)
Control by push button on the front panel, remote control or Web GUI and Remote control APP (Android tablet & iPad)

PANEL DESCRIPTION

Front Panel

A LED INDICATOR
The LED indicator shows system status
B POWER
Press to power on / off the device
C AV MUTE
Press to enable / mute audio and video
D OUTPUT
Press to choose output to display
E SINGLE VIEW
Switch to single view /full screen with specific input
F LAYOUT
Switch to chosen layout
G LCD DISPLAY
Shows device information

Back Panel

H IN 1~4
HDMI input port. Associate to input channels 1 to 4, respectively
I OUT 1~2
HDMI output port, Associate to output 1 and 2 respectively
J AUDIO OUT
3.5mm audio output
K S/PDIF OUT
S/PDIF audio output
L USB 2.0
For debugging purposes only For debugging purposes only
M LAN
For Ethernet connection
(For Web or Remote control APP)
N RS-232 (terminal block format)
The order of RS-232 pin is RX, GND, TX (From the left side to the right)
O DC 12V
Power port for DC 12V Power adaptor (included)

Led Indicators

The following describes LED indicators and their status:

Dim
- NO POWER – No power or power failure
Blue
- Steady: IDLE – Connected, power on but device in standby mode
- Blink: POWER OFF IN PROGRESS – Under power off progress
Green
- Blink: POWER ON IN PROGRESS – Under power on process
- Steady: NORMAL – After power on, under normal operation mode
- Blink once: GET IR SIGNAL – Receive IR signal
Red
- Steady: ERROR/FAILD – Faulty connection, or error occurred, need to check for errorSteady: ERROR/FAILD – Faulty connection, or error occurred, need to check for error
Orange
- Steady: POWER OFF CONFIRM – Remote control switch off mode confirmation status

Remote Control

O POWER
On: press once to switch on device Off: press twice to switch off device
P SINGLE VIEW．REGION INPUT
Region input to choose from input port 1~4. Associate to input channels 1 to 4, respectively. You can choose from any of the input source 1~4 to display on output 1 or output 2
Q LAYOUT
Choose any of the 6 layouts to view on output 1 or output 2
R REGION
Press to choose region on output 1 or output 2
S MUTE
Press to enable or mute video or audio

CONNECTION DIAGRAM

MaitreView™ 4KLite allows the user to connect up to FOUR 4K/UHD multi-video sources which may simultaneously output on TWO 4K/UHD displays. MaitreView™ 4KLite allows the user to connect up to FOUR 4K/UHD multi-video sources which may simultaneously output on TWO 4K/UHD displays.
AV LINK MaitreView 4KLite Multi-Window 4

PACKAGE CONTENTS

MaitreView™ 4KLite unit
Rack-Mount Bracket * 2
Screws (for Brackets) * 6
Adaptor: IN:100V-240VAC OUT: DC 12V/5A LOCK DC JACK
Remote control
Quick Start Guide
SYSTEM REQUIREMENTS

Minimum:

720p/HD input source
1080p/FHD output display

Recommended :

4K/UHD input sources * 4
4K/UHD output displays * 2
Ethernet cable (Cat 5e, for Web control and Remote control APP) * 1
For Web: Google Chrome
For Android tablet APP: Android tablet with Android 7.0
For iPad APP: iPad with latest iPadOS version

INSTALLATION

Note: please turn the power off for your displays and video sources before you begin the installation.

Turn the device to the back, connect each video source to the input ports respectively.
Connect each display to the output ports respectively.
Connect the power adapter to the DC 12V power port, and locking the DC power jack. The LED will turn blue after connected successfully.
Once step1~3 is completed, please turn the device to the front and turn the power on for displays and video sources.
Power on your device: on your front panel, press the POWER button once, the blue LED will start to blink for around 30 seconds.
After the LED turn green, then the device is ready to use.
Power off your device: when you wish to turn off the power, please long press the POWER button for around 3 seconds, the LED will blink in blue for around 20 seconds, and then the device will shut down itself.

REMOTE CONTROL
Single View
Single view allows user to output a single region from any of the HDMI IN 1~4 channels, you can press from 1~ 4 on output 1 or output 2. To do this you need to:
Press any of input 1~4 on SingleView . Region Input

Press 1~4 to choose one region layout from input source 1~4 to display on output 1 or output 2,for example press on output 2, then single view displays selected input on full screen in output 2

Layouts
Layout button allows user to choose any of the 6 layouts to show on output 1 or output 2. To do this you need to:
Select the layout from either of the 6 layouts pattern

Select layout by press the button next to the layout icon you wish to use, for example, press once on layout section, then layout will show on output 2

Region Source
Region source allows user to take turns tagging one region clockwise, to do this you need to:
Press Region button ► Press any of input 1~4 on SingleView . Region Input

Press Region button to tagging a region on output, for example this case, press Region from output 2, a blue border will appear on the Region, you may repletely press Region choose desire region
Then you may can press any of Single View . Region input button1~4 to select the desired region

Specifications

Video Processing

Technology| MaitreView™
Performance| Inputs & Outputs up to 4K/60Hz
Max. number of the split layer| 4 split layers on each output port
Seamless Switch| Available when changing sources or Presets
Region| 1 per layer, Max 4 layers per output
Configuration & Control

Interface