XINHAILIN XHL-ARFID Contactless Card Reader Module Owner’s Manual
- June 11, 2024
- XINHAILIN
Table of Contents
**XINHAILIN**
Contactless Card Reader XHL-ARFID
Specification
RFID module
XHL-ARFID Contactless Card Reader Module
While the information provided in this document is made as comprehensive and
accurate as possible, and the contents of this document may be updated soon.
Xinhailin reserves the right to change or terminate its products or services
without advanced notice. Xinhailin advises clients to always obtain the latest
version of the manual before placing orders. No part of this document can be
copied or reproduced in any form, or by any means, without written consent
from the company.
DONGGUAN XINHAILIN NEW ENERGY TECHNOLOGY CO., LTD. All Rights Reserved
DONGGUAN XINHAILIN NEW ENERGY TECHNOLOGY CO., LTD.
Add: No. 4 factory building, Zhennan Road, nanshe industrial zone, nanshe
village, Chashan, Dongguan
City, Guangdong province
Tel: 0769-81810860
http://www.xinhailin.com
Overview
The XHL-ARFID is card reader module of contactless Xinhailin card which based on 13.56MHz. It can be widely used in the terminal external devices of power, telecommunications, transportation, petrochemical and other industrial occasions.
Main features of product:
- Communication protocols can be customized, default Mingte custom protocol
- Support reading and writing of Mifare 1 (MF1) card (ISO14443)
Interface definition and description
This product adopts RS232 three-wire serial port, sharing the same one J6
interface with power supply.
Communication setting: RS232 level, support baud rate 9600bps, 19200bps,
115200bps, default baud rate 115200bps, 1 start bit, 8 data bits, 1 end bit,
no verification.
Power supply: DC 5V
J6 interface connector specification: 4P-2.54mm pitch vertical connector, as
follows:
| Pin NO | Pin Name | Input/Output | Description |
|---|---|---|---|
| 1 | PW+ | P | Digital power supply |
| 2 | RXD | I | Serial port receive (RS232 level) |
| 3 | TXD | 0 | Serial port send (RS232 level) |
| 4 | GND | G | Digital GND |
Note: The Input (I) and output (O) above are relative to this module
Product identification description
In order to facilitate management, the product identification is attached to card reader’s PCB, the product identification format is described as follows:
Product model Software version Product serial No.
As shown below：
XHL-ARFID
V4.010
2022032829(C)
Performance indexes
| Card Type | Description |
|---|---|
| RF card | IS014443 mifarel card |
| Read & write RF Card performances | |
| R&W distance | About 4cm (Relevant to environment, card and power supply) |
| Electrical characteristics | |
| Working power supply | 5V±5% |
| Working current | ≤150mA(DC 5V) |
| Quiescent current | ≤30mA(DC 5V) |
| Working indicator | |
| Indicator light | D1 status indicator light D6 power supply indicator light |
| Environment conditions | |
| Storage temperature | -40 ~ +75t (no condensation) |
| Working temperature | -20 ~ +50°C(no condensation) |
Installation dimensions
RF board installation dimensions are as follows:
Unit: mm, R is the radius, Installation holes are symmetrical at the center of the plate
Installation environment requirement
RF card reader board is sensitive to the environment, metal can reflect and shield electromagnetic waves, that is, metal has influence on card reader and tag. If there is metal nearby, it will reduce the reading rate of tag. So there are certain requirements forthe installation of reading card board. As shown in follows, when installing, keep the coil part away from the metal, the shadow area not allow the metal iron plate or other structural parts or large electronic coil (such as motor or transformer, etc), the distance from the four sides of the coil to metal is recommended to be more than 4CM.
FCC Statements:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by
the part responsible for compliance could void the user’s authority to operate
the equipment.
Integration instructions for host product manufacturers according to KDB
996369 D03 OEM Manual v01
2.2 LIST OF APPLICABLE FCC RULES:
Compliance with §15.225 regulation
2.3 SPECIFIC OPERATIONAL USE CONDITIONS:
The module is typically use in industrial, household and general office / ITE
and audio & video, EV charging system end-products. The product must not be
co-located or operating in conjunction with any other antenna or transmitters.
2.4 LIMIT MODULE PROCEDURES:
The module compliance with FCC requirements based on Limit module procedure as
no shielding cover included.
Any installation or operation that does not follow this manual will require
further evaluation.
2.5 TRACE ANTENNA DESIGNS:
The module was designed with the fixed PCB print antenna, any changes or
modifications by the OEM integrator will require additional testing and
evaluation.
2.6 RF EXPOSURE CONSIDERATIONS:
The module has been evaluated and shown compliant with the FCC RF Exposure
limits under portable exposure conditions. OEM integrator shall equipped the
antenna to compliance with antenna requirement part 15.203& 15.204 and must
not be co-located or operating in conjunction with any other antenna or
transmitters, otherwise, a Class II Permissive Change (C2PC) must be filed
with the FCC and/or a new FCC authorization must be applied.
2.7 ANTENNAS:
The antenna of the module was deisgned as PCB printed on the PCBA board and
the best gain is 0dBi. Modification the antenna design may need additional
testing and evaluation.
2.8 LABEL AND COMPLIANCE INFORMATION:
The final end product must be labelled in a visible area with the following
“Contains TX FCC ID: or “Contains Transmitter Module FCC ID: 2A9TCXHL-ARFID”
2A9TCXHL-ARFID ”. If the size of the end product is smaller than 8x10cm, then
additional FCC part 15.19 statement is required to be available in the users’
manual: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
A user’s manual for the finished product should include one of the following
statements:
For a Class A digital device or peripheral, the instructions furnished the
user shall include the following or similar statement, placed in a prominent
location in the text of the manual:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
For a Class B digital device or peripheral, the instructions furnished the
user shall include the following or similar statement, placed in a prominent
location in the text of the manual:
This equipment has been tested and found to comply with the limits for a Class
B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The User’s Manual for The finished product should include the following
statements:
Any changes or modifications to this equipment not expressly approved by the
OEM/Integrator may cause harmful interference and void the user’s authority to
operate this equipment.
RF Exposure
This device has been evaluated and shown compliant with the FCC RF Exposure
limits under portable fixed exposure conditions.
2.9 INFORMATION ON TEST MODES AND ADDITIONAL TESTING REQUIREMENTS:
Data transfer module demo board can control the EUT work in RF test mode at
specified conditions. This radio module must not be installed to co-locate and
operating simultaneously with other radios in the host system except in
accordance with FCC multi-transmitter product procedures. Additional testing
and equipment authorization may be required operate simultaneously with other
radio.
2.10 ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER:
The host product manufacturer is responsible for compliance with any other FCC
rules that apply to the host not covered by the modular transmitter grant of
certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
General Statements
The module is intended only for OEM integrators.
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
The OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
OEM integrator shall not modify and change the fixed designed PCB print
antenna, and must not be co-located or operating in conjunction with any other
antenna or transmitters, otherwise, a Class II Permissive Change (C2PC) must
be filed with the FCC and/or a new FCC authorization must be applied.
.The product is typically use in industrial, household and general office /
ITE and audio & video, EV charging system end-products.
| DONGGUAN XINHAILIN NEW ENERGY TECHNOLOGY CO., LTD. | File NO.: XHL-ARFID |
|---|---|
| Name | XHL-ARFID Specification |
| B2 | 2022-07-13 |
Documents / Resources
|
XINHAILIN XHL-ARFID Contactless Card Reader
Module
[pdf] Owner's Manual
2A9TCXHL-ARFID, XHL-ARFID, XHL-ARFID Contactless Card Reader RFID Module,
Contactless Card Reader RFID Module, Card Reader RFID Module, RFID Module
---|---