unibono YP-7108 Hair Clipper User Manual

unibono YP-7108 Hair Clipper

HAIR CLIPPER USER MANUAL PLEASE READ THE MANUAL BEFORE USING AND SAVE IT

PRODUCT SPECIFICATION

• Name Electric Hair Clipper
• Model no. YP-7108
• Battery capacity 2000mAh
• Input 5V/1A
• Charging Time Approx. 220 minutes
• Running Time Approx. 180 minutes
• Dimension 7.01 x 1.34 x 1.30 inch (main body) 2.56 x 2.56 x 1.61 inch (base)
• Weight 6.95 oz. (main body) 3.1 oz. (base)

PRODUCT CONFIGURATION

1. Hair clipper
2. 1/8″ Guard
3. 1/4″ Guard
4. 3/8″ Guard
5. 1/2″ Guard
6. Charging base 8
7. USB cable
8. Brush
9. Detachable blade
10. On/Off/Shift switch
11. LCD indicator
12. Charging port

LCD DISPLAY INDICATOR

• Status of LCD display Description
• Flashing light Recharging
• Steady light Fully charged
• 5.0Kr/min Low speed
• 6.0Kr/min High speed
• Light flash 4 times Run time display 000 Low voltage protection No speed indicator
• All icons flash together quickly High voltage protection

HAIR LENGTH SETTING

Using a guide comb can fix and trim the corresponding length of your hair, avoid the operation error and effectively control the overall thickness of your hair style.

INSTALLATION INSTRUCTIONS

HOW TO TURN ON/OFF CLIPPER

• Long press for Power On/off.
• Short press for high/low speed shift.

HOW TO INSTALL AND REMOVE BLADE

1. To remove blade, hold the clipper with front of blade teeth facing away,push the blade cartridge out, using the thumb cut out on the back of the clipper.
2. To reattach blade, align the blade connection A into the main body slot B.
3. Press down firmly on the back of the clipper until a soft sound .

HOW TO INSTALL AND REMOVE GUIDE COMB

1. Guide combs should be installed by first hooking the blade teeth to its front side.
2. Press the back of the guide comb down until it snaps into place.
3. To remove, pull the snap tab on back side of guide comb and pull the comb off.

Note : Turn off the clipper before installing and removing. Ensure comb is attached before a hair cut

CLEANING AND MAINTENANCE

1. Brush the accumulated hair from the clipper.
2. Detach blade and remove hair by pressing down its holder.
3. Rinse blades and oil them in the circled position.
4. Rinse the main body with running water.
5. Ensure a thoroughly wiped dry after cleaning the clipper body and blades.

MAINTENANCE CAUTION

Make sure the clipper is off before cleaning and maintenance

• Clean the surface and remove all loose hairs from the blades after every use.
• Do not remove the spring of the blade in case of a fit error or scrap.
• It is recommended to oil the blades after every use.
• Do not immerse clipper in water or other liquids.
• Do not wipe the body with gasoline,alcohol,banana oil or harsh corrosive chemicals.
• The life of the blade is related to use frequency, hair quality and maintenance. Timely replacement of worn blade can effectively avoid clipping hair; If replace, please consult our after-sales service team directly for the original blade accessories.
• It may be slightly hot when the blades work,it is normal.

HOW TO CHARGE

Clipper must be turned off.

• Insert the charging cable into the rear port of the clipper or the base.
• Plug into power through USB adapter or power bank,computer etc.
• Switch off and charge the clipper fully before its first use.
• Three hours fully charge provides 220 minutes of use.
• Make sure to charge your clipper with input 5V= 1A.

WARNING
To reduce the risk of burns, fire, electric shock or injury to persons:

• Supervision is necessary if this clipper is used by children or persons with disabilities.
• Use this clipper only for its intended use as described in this manual.
• Do not use attachments not recommended by the manufacturer.
• Do not operate this clipper if it is not working properly or damaged .
• Do not disassemble this clipper by yourself.
• Do not charge at temperatures above 40°C or below 0°C, as this will reduce battery capacity and shorten its lifespan.
• Please unplug the charger in time after fully charge to lengthen the battery’s life.
• This clipper may heat up during use and charging, this is normal.
• Never operate this clipper with a damaged cord or plug.
• Keep the clipper away from wet area.

TROUBLESHOOTING

Clipper blades do not move:

• The blade unit may be dirty and clogged. Clean the unit as directed in Cleaning and Maintainance section.
• Always clean and oil the blade and clipper before storing.

Clipper does not hold charge:
Fully discharge battery by running clipper until it stops, then follow charging instructions.

Clipper does not work when turned on :
Clipper must be charged for a full 3-4 hours.

Clipper pulls your hair:

• It may be low power. Try to charge fully.
• Oil the blade evenly before hair cut.

Clipper is too noisy:
Oil blades as directed in previous section of this instruction booklet.

Can’t remove guide comb:
Do not separate the guide comb from clipper forcefully,pull the snap tab on back side of guide comb firstly.then pull the comb off.

Limited One Year Warranty

Unibono will repair or replace your clipper (at our option) free of charge within 12 months from the date of purchase if the clipper is defective in workmanship or materials.For more information, please refer to the after-sales card.

Warranty excludes:
The blades are not included in the limited one year warranty.

This warranty does not cover products damaged by the following:

• Accident, misuse, abuse or alteration of the product.
• Servicing by unauthorized persons.
• Use with unauthorized accessories.
• Connecting ii to incorrect current and voltage.
• Wrapping cord around appliance causing premature wear and breakage.
• Any other conditions beyond our control.

No responsibility, obligation, or liability is assumed for the installation or maintenance of this product.

• Manufacturer : Ningbo Unibono Appliance Co.,Ltd
• Add. : 29 Xinyi Rd, D8lCie Dvpt,Beilun, Ningbo,Zhejiang,China 315812
• Tel.: 008675527225145
• E-mail : aftersales@unibono.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>