electro-harmonix Satisfaction Plus Fuzz Pedal Instruction Manual
- June 11, 2024
- electro-harmonix
Table of Contents
Satisfaction Plus Fuzz Pedal
Product Information
The Satisfaction Plus is a modernized vintage fuzz pedal that offers expanded classic fuzz sounds of the 1960s. It comes in acompact chassis and features a Bias control for wilder tones, a Fat switch for a broader sound, and a versatile tone knob for more sonic sculpting. The pedal has an ATTACK knob that controls the amount of input gain and distortion, and a BIAS knob that controls the signal bias going into the first transistor stage. It has an audio input impedance of 50k, an audio output impedance of 100, and draws a current of 5mA. The pedal requires a 9VDC power supply with center-negative polarity. The Satisfaction Plus has true bypass switching and can be powered with an Electro-Harmonix 9.6DC-200, MOP-D10, or S8 power supply. Using the wrong adapter or a plug with the wrong polarity may damage the device and void the warranty. The power supply should not exceed 18VDC, and power supplies rated for less than 10mA can cause the device to act unreliable. The pedal comes with a warranty that gives the purchaser specific legal rights.
Product Usage Instructions
- Connect your guitar to the INPUT jack of the Satisfaction Plus and the AMP jack to your amp’s input.
- Press the footswitch to ensure the LED is lit.
- Turn all knobs to their 12 o’clock positions.
- Set the toggle switch to NORM for the classic bright fuzz-tone or to FAT for a fuller sound.
- Adjust the ATTACK knob to control the amount of input gain and distortion.
- Adjust the BIAS knob to control the signal bias going into the first transistor stage. Turn the knob counterclockwise for choked or gated fuzz, turn it clockwise for a hollowed-out sound.
- Experiment with the Fat switch and versatile tone knob to sculpt your desired sound.
- Play your guitar!
Modernized Vintage Fuzz
Congratulations on your purchase of the Satisfaction Plus, an expanded take on the classic fuzz sounds of the 1960s. Still in a compact chassis, the Satisfaction Plus adds a Bias control for wilder tones, a Fat switch for a broader sound, and a versatile tone knob for more sonic sculpting.
Operating Instructions
Connect your guitar to the INPUT jack of the Satisfaction Plus and the AMP
jack to your amp’s input. Press the footswitch to ensure the LED is lit. Your
Satisfaction Plus is now ready to play.
A good starting point is to turn all knobs to their 12’oclock positions, then
set the toggle switch to NORM for the classic bright fuzz-tone, or to FAT for
a fuller sound.
POWER SUPPY REQUIREMENTS:
- Voltage: 9VDC
- Current: 5mA
- Polarity: Center-Negative
- Battery: 9V
This device may be powered with an Electro-Harmonix 9.6DC-200, MOP-D10, or S8 power supply. Use of the wrong adapter or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 18VDC on the power plug. Power supplies rated for less than 10mA can cause the device to act unreliably.
Controls and Connections
- ATTACK Knob Controls the amount of input gain and distortion. As you turn this knob clockwise, the Satisfaction Plus ranges from mild drive to saturated fuzz.
- BIAS Knob Controls the signal bias going into the first transistor stage of the Satisfaction Plus. The least compressed and open sound is with BIAS set to noon, which matches the original Satisfaction pedal. Turn the knob counterclockwise for choked or gated fuzz, turn it clockwise for a hollowed-out sound.
- TONE Knob Controls an active tilt-shift type EQ to further shape the fuzz tone. When the TONE knob is at noon the EQ is flat, match-ing the original Satisfaction pedal. Turn the TONE knob counter-clockwise for more lows and less highs. Turn it clockwise for more highs and rolled back lows.
- VOL Knob Sets the output level of the Satisfaction Plus.
- FAT/NORM switch In the NORM position, the Satisfaction Plus has the same overall circuitry as the original Satisfaction pedal. Push the switch to FAT for a bigger, bassier fuzz sound that still cuts through a mix.
- FOOTSWITCH and STATUS LED The footswitch engages or bypasses the effect. The status LED lights when the effect is engaged. The LED is off in bypass mode. The Satisfaction Plus employs True Bypass.
- INPUT Jack Audio input to the Satisfaction Plus.
- AMP Jack Audio output from the Satisfaction Plus.
- 9V Power Jack An optional 9VDC, center-negative power supply can be connected to the power jack to provide power without a battery. The Satisfaction Plus requires 5mA at 9VDC on a center-negative plug. Do not exceed 18VDC at the power jack.
When using a 9V battery, plugging into the INPUT jack activates power. The
input cable should be removed when the unit is not in use to avoid running
down the battery.
To change the 9-volt battery, you must remove the 4 screws on the bottom of
the pedal. Once the screws are removed, you can take off the bottom plate and
change the battery. Please do not touch the circuit board while the bottom
plate is off or you risk damaging a component.
Notes and Specifications
- Audio input impedance at INPUT jack: 50kΩ
- Audio output impedance at OUTPUT jack: 100Ω
- Current draw: 5mA
- Power Supply: 9VDC, Center-negative polarity
- True bypass switching
WARRANTY INFORMATION
Please register online at www.ehx.com/product-
registration or complete and return
the enclosed warranty card within 10 days of purchase. Electro-Harmonix will
repair or replace, at its discretion, a product that fails to operate due to
defects in materials or workmanship for a period of one year from date of pur-
chase. This applies only to original purchasers who have bought their product
from an authorized Electro-Harmonix retailer. Repaired or replaced units will
then be warranted for the unexpired portion of the original warranty term. If
you should need to return your unit for service within the warranty period,
please contact the appropriate office listed below. Customers outside the re-
gions listed below, please contact EHX Customer Service for information on
warranty repairs at info@ehx.com or
+1-718-937-8300.
USA and Canadian cus-tomers: please obtain a Return Authorization Number
(RA#) from EHX Cus-tomer Service before returning your product. With your
returned unit, include a written description of the problem as well as your
name, address, telephone number, e-mail address, RA# and a copy of your
receipt clearly showing the purchase date.
United States & Canada
EHX Customer Service
Electro-Harmonix
co New Sensor Corp.
47-50 33rd Street
Long Island City, NY 11101
Tel: 718-937-8300
Email: info@ehx.com
Europe
John Williams
Electro-Harmonix UK
13 Cwmdonkin Terrace
Swansea SA2 0RQ
United Kingdom
Tel: +44 179 247 3258
Email:
electroharmonixuk@virginmedia.com
This warranty gives a purchaser specific legal rights. A purchaser may have even greater rights depending upon the laws of the jurisdiction within which the product was purchased.
The CE logo indicates that this product has been tested and shown to conform
with all applicable European Conformity directives.
The WEEE or “trashcan” logo indicates that this product is made up of
electronic components that should not be trashed alongside household waste but
instead should be recycled by a proper electrical waste facility.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>