GAGGENAU VR230620 200 Series Vario Electric Grill Instruction Manual
- June 11, 2024
- Gaggenau
Table of Contents
- VR230620 200 Series Vario Electric Grill
- Appliance Handling Safety
- Safety Codes and Standards
- Electric Safety
- Related Equipment Safety
- Before you begin
- Countertop Requirements
- Installation Procedure
- Removing appliance
- Customer Service
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VR 230 620
Electric grill
Installation instructions2
Instruction Manual
VR230620 200 Series Vario Electric Grill
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE
APPLIANCE AFTER INSTALLATION IS COMPLETE.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR’S USE.
WARNING
If the information in this manual is not followed exactly, fire or shock may
result causing property damage or personal injury.
WARNING
Do not repair, replace or remove any part of the appliance unless specifically
recommended in the manuals. Improper installation, service or maintenance can
cause injury or property damage. Refer to this manual for guidance. All other
servicing should be done by an authorized service provider.
Appliance Handling Safety
Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.
Safety Codes and Standards
This appliance complies with one or more of the following Standards:
- UL 858, The Standard for the Safety of Household Electric Ranges
- UL 923, The Standard for the Safety of Microwave Cooking Appliances
- UL 507, The Standard for the Safety of Electric Fans
- ANSI Z21.1, The American National Standard for Household Cooking Gas Appliances
- CAN/CSA-C22.2 No. 113 Fans and Ventilators
- CAN/CSA-C22.2 No. 61 Household Cooking Ranges
- CAN/CSA-E60335-1
- CAN/CSA-E60335-2-6 Household and similar electrical appliances – Safety
It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.
Electric Safety
WARNING
Before you plug in an electrical cord or turn on power supply, make sure all
controls are in the OFF position.
If required by the National Electrical Code (or Canadian Electrical Code),
this appliance must be installed on a separate branch circuit.
WARNING
Risk of electrical shock or fire!
Frame grounded to neutral through a ground strap. Grounding through the
neutral conductor is prohibited for new branch-circuit installations (1996
NEC), mobile homes, and recreational vehicles, or in an area where local codes
prohibit grounding through the neutral conductor.
For installations where grounding through the neutral conductor is prohibited,
- disconnect the link from the neutral,
- use grounding terminal or lead to ground unit,
- connect neutral terminal to lead branch circuit neutral in usual manner (when the appliance is to be connected by means of a cord kit, use a UL listed 4-conductor cord for this purpose).
Be sure your appliance is properly installed and grounded by a qualified
technician. Installation, electrical connections and grounding must comply
with all applicable codes.
Before installing, turn power OFF at the service panel. Lock service panel to
prevent power from being turned ON accidentally.
Installer – show the owner the location of the circuit breaker or fuse. Mark
it for easy reference.
Related Equipment Safety
The appliance should only be used if installed by a qualified technician in
accordance with these installation instructions. The manufacturer is not
responsible for any damage resulting from incorrect installation.
Remove all tape and packaging before using the appliance. Destroy the
packaging after unpacking the appliance.
Never allow children to play with packaging material.
Never modify or alter the construction of the appliance. For example, do not
remove leveling legs, panels, wire covers or anti-tip brackets/screws.
To eliminate the risk of burns or fire by reaching over heated surface units,
cabinet storage space located above the surface units should be avoided. If
cabinet storage is to be provided, the risk can be reduced by installing a
hood that projects horizontally a minimum of 5 inches (127 mm) beyond the
bottom of the cabinet.
Verify that cabinets above the cooktop are a maximum of 13″ (330 mm) deep.
When installing a cooktop over a single oven, be sure to follow both the
oven’s and cooktop’s installation manuals.
Ventilation Recommendations
We strongly recommend the installation of a ventilation hood above this
appliance. The hood must be installed according to instructions furnished with
the hood.
CAUTION
The appliance should not be installed with a ventilation system that blows air
downward toward the burners. This type of ventilation system may cause
ignition and combustion problems with the gas cooking appliance resulting in
personal injury or unintended operation.
Proposition 65 Warning:
This product may contain a chemical known to the State of California, which
can cause cancer or reproductive harm.
Therefore, the packaging of your product may bear the following label as
required by California:
STATE OF CALIFORNIA PROPOSITION
WARNING: ALS, WARNING Cancer and Reproductive Harm –
www.P65Warnings.ca.gov
Before you begin
Before you beginTools and Parts Needed
- Phillips Head Screwdriver
- Pencil
- Drill with ¼” (6 mm) bit
- Jigsaw
- Tape Measure
Note: Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer.
Parts Included
Installation accessories
VD 200 020 Black appliance cover
VV 200 010 Stainless steel connection strip for combining with other Vario 200
appliances
VV 200 020 Black connection strip for combining with other Vario 200
appliances
Use the accessories only as indicated. The manufacturer assumes no liability
for incorrect usage of the accessories.
Cabinet Requirements
The minimum spaces that must be maintained when installing the electric grill
shall be:
A minimum 30″ (762 mm)
B minimum 8″ (200 mm)
C minimum 1 9/16″ (40 mm)
D Stainless steel work surfaces: both work surfaces must be permanently fitted
on both sides of the grill to protect the countertop when the grill is
installed separately.
When installed next to another Vario appliance, a work surface must be fitted
on the opposite side to protect the countertop.
When installed between two other Vario appliances, no work surface is
required.
The distance from the top of the cooktop to the bottom of cabinets above can
be reduced to 24 inch when the bottom of the wood or metal cabinet is
protected by not less than ¼ inch (6.35 mm)-thick flame-retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015 inch (0.4 mm)
stainless steel, 0.024 inch (0.6 mm) aluminum or copper.
Countertop Requirements
WARNING
To reduce the risk of ignition of surrounding combustible materials, install
at least 8″ (200 mm) from both sidewalls and at least 2″ (50 mm) from the rear
wall.
The countertop must be level and horizontal. The stability of the countertop
must be maintained after the cut-out has been made.
Installation Procedure
Prepare Installation Space
Create the cut-out in the countertop for one or several Vario appliances
according to the installation diagram.
The angle of of the cut surface to the countertop must be 90°.
After creating cut-out, remove shavings. Seal cut surfaces in a heat-resistant
manner.
Some solid surface countertops require special installations. For example,
heat reflective tape and rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to your countertop.
Observe minimum distance between appliance underside and furniture parts of
3/8″ (10 mm).
When installing multiple Vario appliances: Take into account space requirement
for VV 200 010/020 connection strip between the appliances. Appliances can
also be installed
in individual cut-outs, bearing in mind a minimum distance between the
appliances of 1 9/16″ (40 mm).
Install Appliance
WARNING
Before you plug in an electrical cord or turn on power supply, make sure all
controls are in the OFF position.
-
Secure the appliance cover VD 200 020 (available separately as special accessory) before fitting on the appliance.
-
If the appliance is not being covered, seal the openings on the back of the appliance using the cover caps supplied.
-
Place the appliance evenly in the cut-out. Push it down firmly into the cut-out.
Note: The appliance must sit securely in the cut-out and must not be able to move around (e.g. during cleaning). If the width of the cut-out is at the upper tolerance limit, secure battens to the sides of the cutout if necessary. -
Remove the lava stones from the film and place them in the lava stone tray. Insert the components as shown in the pictures.
Connect Electrical Supply
Refer to data plate for more information. See “Service” for data plate
location.
The branch-circuit breakers ampacity, the wire sizes and the connections must
be conform to the requirements of the National Electrical Code or Canadian
Electrical Code and all local codes and ordinances.
Attach flexible conduit to the junction box. Connect the lead wires to the
junction box supply wires in proper phase:
- black (L1) to black
- red (L2) to red
- green to ground
The mains connecting cable must at least correspond to the type SJTO 3×16 AWG 105°C. The mains connecting cable must only be purchased through and connected by an authorised specialist.
Connection with a plug
- Plug has to be conform with NEMA CONFIGURATIONS FOR PLUGS AND RECEPTACLES.
- The appliance must be properly grounded.
- Plug must be rated not less than type 6-20 P (2-pole 3wire grounding).
- Only a qualified electrician should connect the plug.
- Install a socket outlet earthed in accordance with regulations approx. 27″ (700 mm) above the floor behind the appliance. The socket outlet must still be accessible after installation.
Check the Installation
WARNING
Before you plug in an electrical cord or turn on power supply, make sure all
controls are in the OFF position.
Remove everything from the cooktop surface. Clean cooktop surface with cooktop
cleaning creme.
Switch on the circuit breaker.
Verify that elements function properly.
Removing appliance
Disconnect the appliance from the power supply. Push out the appliance from
below.
CAUTION
Damage to appliance! Don’t lift device out from above.
Customer Service
Customer ServiceIf your appliance needs repairs, our customer service is there
for you. We work hard to help solve problems quickly and without unnecessary
service calls, getting your appliance back up and running correctly in the
least amount of time possible.
When you call, please indicate the product number (E-Nr.) and serial number
(FD-Nr.) so that we can support you in a qualified manner. You will find the
type plate with these numbers on the bottom of the appliance. To avoid having
to search for a long time when you need it, you can enter your appliance data
and the customer support telephone number here.
E-Nr. | FD-Nr. |
---|
Please read the installation instructions and use and care instructions
provided with your appliance. Failure to do so may result in an error in using
the appliance. This could result in a service call that instead of fixing a
mechanical issue is only needed for customer education.
Such calls are not covered by the appliance warranty.
Please find the contact data of all countries in the enclosed customer service
list.
To book a service visit and product advice
USA | 877 442 4436 toll-free |
---|---|
CANADA | 877 442 4436 toll-free |
Intended changes opposing release specimen or specification offer must be
advised in time and may only be introduced following written clearance.
Deviating designs will be refused.
The reproduction, transmission or use of this document or its contents is not
permitted without express written authority. Of fenders will be liable for
damages. All rights including rights created by patent grant or registration
of a utilit model or desi n are reserved. Copyright reserved.
BSH Home Appliance Corporation
1901 Main Street, Suite 600
Irvine, CA 92614 1-877-442-4436
www.gaggenau.com/us
© 2022 BSH Home Appliances ![GAGGENAU VR230620 200 Series Vario Electric Grill
- qr](https://manuals.plus/wp-content/uploads/2023/05/GAGGENAU-VR230620-200 -Series-Vario-Electric-Grill-qr.png)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>