Kreg KMA3225 Shelf Pin Jig Owner’s Manual

OWNER’S MANUAL
Keg Shelf Pin Jig
Manual applies to Item

# KMA3225, KMA3232, and KMA3232-INT

KMA3225 Shelf Pin Jig

WARNING Every user must read and follow instructions and safety precautions in this manual. Failure to do so could result in serious injury. Save manual for future reference.

We’re here to help.
We want you to have an exceptional project building experience.
If you have questions or need support, please get in touch. 1-800-447-8638 | technicalsupport@kregtool.com

Tell us about your experience.
Your opinion counts. And we’re always looking for ways to improve. Share your feedback so we can keep growing and innovating for you. www.kregtool.com/feedback

Safety Precautions

WARNING Before using a power tool with this product, read, and follow the tool manufacturer’s instructions and safety precautions in addition to the safety precautions below to reduce risk of serious injury from hazards such as fire, electric shock, or rotating drill bit.

• Follow your drill manufacturer’s safety guidelines.
• Follow your clamp manufacturer’s safety guidelines. Keep your hands clear when clamping to avoid pinch points. The clamping limit on this jig is 300 lbs.
• When drilling, always ensure that the workpiece is clamped securely. It is dangerous to hold the workpiece in place by hand.
• The drill bit is sharp; handle with care and avoid unintended cutting. The drill bit may be hot after repetitive use.
• Always wear personal protective equipment certified as adequate in addition to what your drill manufacturer requires.
• Do not allow familiarity gained from frequent use of your tools to replace safe work practices. A moment of carelessness is sufficient to cause severe injury.

WARNING Avoid awkward hand positions where a sudden slip could cause contact with the rotating drill bit.
WARNING Do not operate this tool or any machinery while under the influence of drugs, alcohol, or medications.
WARNING This product can expose you to chemicals including Acrylonitrile and other chemicals, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARNING Drilling, sawing, sanding, or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection.
For more information go to www.P65Warnings.ca.gov/wood.

Pre-Assembly

Review this section before you begin. Ensure you have all tools/materials on hand and compare the package with the items listed in the Product Description section. If any item appears missing or lost, do not use this product. Contact Technical Support or return product to place of purchase.

Recommended Tools/Materials

Product Description

*If replacement or different size drill bits are needed, 1/4″ or 5 mm drill bits are available separately.
**The indexing pin is double ended for both 1/4″ and 5 mm shelf pin holes.

Onboard Tool Storage
The jig (A) provides onboard storage for these items:

• Hex wrench (G)
• Indexing pin (E)
• Drill bit (C) with  stop collar (D) attached

Assembly

1. Set the Stop Collar on the Drill Bit
   a. Slide the stop collar (D) onto the drill bit (C).
   b. Place the drill bit (C) and stop collar (D) into the storage slot on the back of the jig (A).
   c. Slide the end of the drill bit (C) into the hole on the edge of the storage slot until it stops.
   d. Position the stop collar (D) into the recess of the storage slot.
   e. Use the hex wrench (G) to tighten the set screw in the stop collar (D).

2. Identify Your Cabinet Type
   **** For face-framed cabinets, continue to the next section.| For frameless cabinets, skip to Attach the Fence to the Jig (page 6).
   ---|---
   |

For face-framed cabinets, continue to the For frameless cabinets, skip to Attach

Face-Framed Cabinets

1. Position the Jig
   Tip Although you can use either the top or bottom of the jig for reference, we recommend using the top so that you can use the jig extension as you move downward. Use the same reference end of the jig while drilling all shelf pin holes to maintain accurate left to right and front to back alignment.
   a. Align the jig with the inside corner of the cabinet and the face-frame.

2. Clamp the Jig
   WARNING Follow your clamp manufacturer’s safety guidelines. Keep your hands clear when clamping to avoid pinch points. The clamping limit on this jig is 300 lbs.
   a. Use a clamp in the location shown below to secure the jig (A) in place. b. If using two connected jigs, clamp both.
   Tip If your cabinet is already assembled, remove the fence and place the jig against the back of the cabinet using the same reference point as the front and carefully hold in place while you drill your first hole. Then use the jig extender and index pin to continue.

Frameless Cabinets

1. Attach the Fence to the Jig
   a. Insert the fence (B) into the jig (A) base.
   b. Slide the fence (B) horizontally to secure it in place.
   Note To remove the fence (B), slide the fence horizontally and pull away from the jig (A).

2. Position the Jig
   Tip Although you can use either the top or bottom of the jig for reference, we recommend using the top so that you can use the jig extension as you move downward. Use the same reference end of the jig while drilling all shelf pin holes to maintain accurate left to right and front to back alignment.
   Note When moving from the front to back holes, attach the fence to the other side of the jig.
   a. Align the jig with the inside corner of the cabinet and the fence with the front of the cabinet.

3. Clamp the Jig
   WARNING Follow your clamp manufacturer’s safety guidelines. Keep your hands clear when clamping to avoid pinch points. The clamping limit on this jig is 300 lbs.
   a. Use a clamp in the location shown below to secure the jig (A) in place.
   b. If using two connected jigs, clamp both.
   Tip If your cabinet is already assembled, remove the fence and place the jig against the back of the cabinet using the same reference point as the front and carefully hold in place while you drill your first hole. Then use the jig extender and index pin to continue.

Operation

1. Drilling the Shelf Pin Holes
   WARNING When drilling, always ensure that the workpiece is clamped securely. It is dangerous to hold the workpiece in place by hand. The drill bit is sharp; handle with care and avoid unintended cutting. The drill bit may be hot after repetitive use.
   a. Place your prepared drill bit (C) with stop collar (D) into your drill.
   b. Insert your drill bit (C) into the drill guide (1) and bring your drill up to speed before contacting the wood.
   c. Drill until the stop collar (D) stops going any deeper due to contact with the drill guide.
   d. Remove the drill bit (C) from the drill guide while the drill bit is still rotating.

2. Drilling an Extended Run of Shelf Pin Holes
   Note The drill extension does not have a drill guide and should not be used for drilling.
   a. Drill the first set of shelf pin holes.
   b. Unclamp the jig (A).
   c. Connect the jig extension (F) to the top of the jig (A).
   d. Slide the jig (A) to align the jig extension (F) hole with the last shelf pin hole.
   e. Insert the indexing pin (E) through the jig extension (F) and shelf pin hole to stabilize the jig (A).
   f. Clamp the jig (A) in place.
   g. Drill the next set of shelf pin holes.
   Tip If you need to start your holes from the bottom, remove the jig extension (F) and use the indexing pin (E) in the drill guides and existing holes for alignment.

Using the Jig for Cabinet Hardware Installation

When building frameless cabinets, the jig can be used to correctly mount concealed hinge plates and first hole alignment for most drawer slides.
Note Check your hardware mounting instructions before drilling. The drill guide holes are 1.45″ (37 mm) from the sides of the jig with 1.25″ (32 mm) between holes.

Marking Concealed Hinge Mounting Holes

a. Mark the desired center line of the hinge on the cabinet.
b. Position the jig (A) using the position indicator window to align the center of the two drill guide holes.
c. Clamp the jig to the frameless cabinet.
Important To use the provided screws from the hinge manufacturer, only use the drill bit to mark the location of the screws.
d. If using a standard wood screw, bring your drill up to speed and lightly touch the cabinet to break the surface.
e. If using a 5 mm system screw, use the 5 mm drill bit to drill the hole.

Marking Drawer Slide Mounting Holes

a. Mark the desired center line of the drawer slide on the cabinet.
b. Position the jig (A) using the position indicator window to align the drill guide hole.
c. Clamp the jig to the frameless cabinet.
Important To use the provided screws from the slide manufacturer, only use the drill bit to mark the location of the screws.
d. If using a standard wood screw, bring your drill up to speed and lightly touch the cabinet to break the surface.
e. If using a 5 mm system screw, use the 5 mm drill bit to drill the hole.
f. Attach the slide with the first screw and level to attach the remaining screws.

Connect Jigs Together

Connect two or more jigs together for longer drilling capability. Insert the top of the second jig into the extension connector at the bottom of the first jig.

Maintenance

Keep all parts clean of dust and debris. Replace the drill bit when it is dull.

Care and Cleaning

To clean, wipe with a clean rag or blow compressed air on all parts. To store, place all parts and hardware into the storage positions on the back of the jig.

Troubleshooting

the drill to forward.
It is difficult to drill the hole.| The bit is dull.| Replace the bit.
There is excessive tear out on holes.| The bit is dull.| Replace the bit.
The jig is not clamped properly.| Check and clamp the jig properly.
The drill bit is started while it is in contact with the wood.| Insert the drill bit into the drill guide and bring the drill up to speed before contacting the wood.
The side to side alignment is off.| Not using the same reference end.| Use the same reference end for both sides of the cabinet.

Accessories

EXPLORE. BUILD. SHARE.
We’re makers just like you.
That’s why we love to see what you’re working on.
Share with the community and get inspired!
#madewithKreg
Get free plans, project resources, and more.
kregtool.com and buildsomething.com

References

• Projects & Plans | Kreg Tool
• Welcome to Kreg Tool
• Homepage | Optimale
• P65Warnings.ca.gov
• P65Warnings.ca.gov/wood
• P65Warnings.ca.gov
• P65Warnings.ca.gov/wood

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>