COOPER Notification SPMNS-MIC MNS Microphone Installation Guide

SPMNS-MIC MNS Microphone

Product Information

The SPMNS-MIC MNS Microphone is a UL Listed product that is designed to be used with Cooper Notification’s SPMNS SAFEPATH Panel. It provides a means for making emergency voice announcements from the SPMNS panel. The product comes in two variants: Surface Mount and Flush Mount. Only 1 MNS Microphone can be connected to the SPMNS panel. The hand-held push-to-talk microphone is supervised to ensure proper connection. The product is not repairable. If it is detached from the unit, the unit must be returned for repair.

The product specifications are:

• Power Input Voltage: 24VDC

• Audio Output Level: 1.05V RMS

• Output Impedance: 600 Ohms

• Min. Ground Fault: 20k Ohms

• Input Current Operating Temperature: Standby: 23mA / Alarm: 30mA, 0 to 49C (32 to 120F)

• Dimensions (H x W x D): Surface Front: 9 x 14-1/2 x 3 1/2 in.
  Flush Front: 10 x 15-1/2 x 3 1/2 in.

• Wiring Specifications: Cable Size: 14-18 American Wire Gauge (AWG) Shielded. Maximum Length: SPRM-MIC must be adjacent to the SPMNS panel. Maximum Capacitance: 0.1uF/Total Run (50pF/foot for 1000 FT.)

Product Usage Instructions

Follow the below instructions for proper installation, mounting and operation of the SPMNS-MIC MNS Microphone:

1. Installation:
   • Use the product according to the instruction manual.
   • The MNS Microphone is UL Listed for indoor use only.
   • The product is designed to be used with Cooper Notification’s SPMNS SAFEPATH Panel.
   • Only 1 MNS Microphone can be connected to the SPMNS panel.
   • The hand-held push-to-talk microphone is supervised to ensure proper connection.
   • If it is detached from the unit, the unit must be returned for repair.
2. Mounting:
   • Install backbox (either flush or surface) adjacent to the SPMNS panel. Be sure that the mounting box is level.
   • Attach the 6 wires as shown in the wiring diagram (Figure 1). Be sure to use the specified wire and run the wire through conduit.
   • Attach the mounting plate to the box with the 4 screws as shown in Figure 2.
3. Operation:
   • Set switch SW6 (NAC/CC) to the CC position.
   • Set the jumper on J4 to the 1V position.
   • Remove the jumper on JP4. (Warning: If JP4 jumper is not removed, the SPMNS will not be able to detect any mass notification mic trouble.)

INSTALLATION INSTRUCTIONS

SPMNS-MIC MNS MICROPHONE FOR USE WITH SPMNS

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

MODEL NUMBER:

• SPMNS-MIC -SB Surface Mount
• SPMNS-MIC -FB Flush Mount

GENERAL:
The MNS Microphone is UL Listed under Standard 864, Control Units for Fire- Protective Signaling Systems. They are Listed for indoor use only. The MNS Microphone is designed to be used with Cooper Notification’s SPMNS SAFEPATH Panel. It provides a means for making emergency voice announcements from the SPMNS panel. Only 1 MNS Microphone can be connected to the SPMNS panel. The hand held push-to-talk microphone is supervised to ensure proper connection. It is not repairable. If it is detached from the unit, the unit must be returned for repair.

NOTE: All CAUTIONS and WARNINGS are identified by the symbol
. All warnings are printed in bold capital letters.

WARNING: PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. FAILURE TO COMPLY WITH ANY OF THE FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

SPECIFICATIONS:

Power Input Voltage:| 24VDC
Audio Output Level:| 1.05V RMS
Output Impedance:| 600 Ohms
Min. Ground Fault:| 20k Ohms
Input Current| Standby: 23mA / Alarm: 30mA
Operating Temperature| 0 to 49C (32 to 120F)
Dimensions (H x W x D)| Surface Front:       9 x 14-1/2 x 3 1/2 in.
(H x W x D)| Flush Front:        10 x 15-1/2 x 3 1/2 in.

WIRING DIAGRAM:
Figure 1 shows the proper wiring connections for connecting the SPMNS-MIC to the SPMNS.

Figure 1:

• This wiring is power limited.
  NOTE: All wiring is supervised unless otherwise noted.

WIRING SPECIFICATIONS

• Cable Size: 14-18 American Wire Gauge (AWG) Shielded. The shield must be connected only at the SPMNS Panel.
• Maximum Length: SPRM-MIC must be adjacent to the SPMNS panel.
• Maximum Capacitance: 0.1uF/Total Run (50pF/foot for 1000 FT.)

MOUNTING INSTRUCTIONS:

Figure 2:

SPMNS-MIC exploded view (surface mount shown)

Figure 2 shows the proper mounting requirements for the SPMNS-MIC.

1. Install backbox (either flush or surface) adjacent to the SPMNS panel. Be sure that the mounting box is level.
2. Attach the 6 wires as shown in the wiring diagram (Figure 1). Be sure to use the specified wire and run the wire through conduit.
3. Attach the mounting plate to the box with the 4 screws as shown in Figure 2.

OPERATING INSTRUCTIONS: Figure 3 shows the locations of the switches and LED’s on the SPMNS that require operation during operation and troubleshooting.

1. Set switch SW6 (NAC/CC) to the CC position.
2. Set the jumper on J4 to the 1V position.
3. Remove the jumper on JP4.

WARNING: IF JP4 JUMPER IS NOT REMOVED THE SPMNS WILL NOT BE ABLE TO DETECT ANY MASS NOTIFICATION MIC TROUBLE.

Figure 4:

Figure 4 shows the SPMNS-MIC front panel and the location of the LED’s.
The green LED indicates there are no faults in the SPMNS-MIC. The yellow LED indicates a trouble condition has occurred in the SPMNS-MIC. The red LED indicates the SPMNS-MIC is ready to transmit the live voice of the operator.

1. With the mouth one to two inches from the microphone, press the microphone push-to-talk button and speak into the microphone and deliver the live audible announcement.

TROUBLE SHOOTING

The yellow “TROUBLE” LED illuminates when there is a problem with the wiring between the SPMNS.

The wiring problems that can occur can be improper wiring (reversed) on the Audio connections and/or CC connections. This will also provide a trouble condition on the SPMNS panel with the system TROUBLE LED illuminated and the “AUX IN” (Auxiliary Input) LED ON. (The SPMNS internal sounder will also sound.) If checking and/or correcting problems do not correct the trouble, then the SPMNS-MIC should be replaced.

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM COOPER NOTIFICATION MANUALS OR OTHER DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT’S APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT THE SOLE RISK OF THE USER AND COOPER NOTIFICATION WILL NOT HAVE ANY LIABILITY FOR SUCH USE.

Copyright 2015 Cooper Wheelock Inc., dba Cooper Notification. All rights reserved.

firealarmresources.com

References

• Fire Alarm Resources | Download fire alarm documents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>