AEA KU4 Ribbon Microphone Owner’s Manual
- June 9, 2024
- AEA
Table of Contents
- AEA KU4 Ribbon Microphone
- AEA KU4 Classic Supercardioid Ribbon Mic
- Product Usage Instructions
- Phantom Power
- Microphone Storage
- Air Turbulence
- INTRODUCTION
- WARRANTY
- GENERAL GUIDELINES
- APPLICATIONS ADVICE
- SPECIFICATIONS
- POLAR PATTERN
- FREQUENCY RESPONSE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AEA KU4 Ribbon Microphone
AEA KU4 Classic Supercardioid Ribbon Mic
The AEA KU4 is a studio ribbon microphone that is designed to provide consistent and reliable performance. It features pure aluminum ribbon material and parts that are interchangeable with the original RCA KU3A. The microphone is a reincarnation of the RCA 44 microphone and has gained a world-wide reputation for its high-quality performance.
Product Usage Instructions
Warranty
The AEA KU4 comes with a one-year limited warranty on parts and labor. You can extend the warranty to a full three years by registering your product with AEA. To register, scan the QR code or visit the AEA website.
Support
If you encounter any problems with your KU4 microphone or have questions
regarding specific applications, please contact the AEA customer support team
at orders@ribbonmics.com for the quickest
response. You can also call
+1-800-798-9127 from 9:00 a.m.- 5:00
p.m. PST Monday-Friday. AEA’s repair center is located at 1029 N.
Allen Ave, Pasadena, CA 91104, U.S.A.
General Guidelines
Your microphone is a valuable and important investment. To keep it functioning
properly, it requires basic care and common sense.
Here are some guidelines to follow:
Phantom Power
Phantom power is not required or recommended for the passive KU4. Passive ribbons such as the KU4 can be damaged if ground (Pin 1) is accidently shorted, miswired, or hot patched in a patch bay to (Pin 2) or (Pin 3). Using phantom power with a faulty or miswired cable or a defective supply can severely stretch or break a ribbon. Therefore, it is recommended to make disengaging phantom-power before plugging and unplugging the microphone a habit.
Microphone Storage
Store your microphone in a dry, cool place. Avoid exposing it to extreme temperatures, humidity, or dust. Keep it in its case when not in use.
Air Turbulence
Avoid exposing the microphone to strong air turbulence. Ribbon microphones can withstand very high SPL (Sound Pressure Level), but can be damaged by a strong gust of air or high levels of very low frequency sound waves (from a kick drum or bass cabinet). To avoid damage, follow The Hand Test: put the back of your hand where the mic will be positioned; if you can feel the moving air, place a pop-filter between the microphone and the source or simply pull the mic farther back. When recording kick drums or bass guitar cabinets, angle the microphone so that no air blasts the microphone directly on-axis from the front or back.
INTRODUCTION
The KU4 is a side-address ribbon microphone with a supercardioid pickup
pattern. The reduced rear-lobe of the supercardioid pattern means that,
compared to a conventional bi-directional ribbon microphone, the KU4 will have
less pickup of ambient sound
from the rear. This makes it much easier to use in situations where isolation
between instruments is important or under less than ideal acoustics. The
angles of maximum off-axis sound rejection are
at ± 135°, and you can use those angles effectively to minimize reflections
caused by nearby surfaces. The KU4 has been designed to reduce proximity bass
boost to facilitate closer mic placement. The lightly-tensioned, ultra low-
mass ribbon produces response out to 20 kHz (-7 dB) with fast, accurate
transients, and without the upper-midrange ringing common to condenser
microphones. These characteristics make the KU4 well suited for modern studio
music production, and ideal for low strings and brass instruments as well as
vocals.
WARRANTY
Your KU4 comes with a one-year limited warranty on parts and labor,shipping
not included. Registering your product with AEA will extend the warranty to a
full three years.
Scan the QR code or visit our website to register.
SUPPORT
If you should encounter any problems with your KU4 microphone or have
questions regarding specific applications, please contact our customer support
team at orders@ribbonmics.com for the quickest
response.
To contact us by phone, please call
+1-800-798-9127 from 9:00 a.m.- 5:00
p.m. PST Monday-Friday. AEA’s repair center is located at 1029 N. Allen Ave,
Pasadena, CA 91104, U.S.A.
GENERAL GUIDELINES
Your microphone is a valuable and important investment. Like most recording equipment and musical instruments, it requires common sense and basic care to keep it functioning properly. Given care, your new microphone will perform dependably for decades.
PHANTOM POWER
Phantom power is not required or recommended for the passive KU4. With a
correctly wired cable and a properly working phantom power supply, there is
actually little danger of damaging a KU4 microphone with phantom power.
However, passive ribbons such as the KU4 can be damaged if ground (Pin 1) is
accidently shorted, miswired, or hot patched in a patch bay to (Pin 2) or (Pin
3). Using phantom power with a faulty or miswired cable or a defective supply
can severely stretch or break a ribbon.
Since passive ribbon microphones and other transformer-coupled microphones can
be particularly vulnerable to phantom power,
it is recommended to make disengaging phantom power before plugging and
unplugging (the microphone) a habit.
MICROPHONE STORAGE
Keep the microphone covered when it is not in use. This will reduce the damage
that may result from a gust of air. Place the supplied protective bag over the
microphone when it is not in use. For long-term storage, keep the microphone
in its protective case. An unprotected ribbon microphone can attract minute
iron particles, sometimes known as “tramp iron”. If allowed, tramp iron can
penetrate the screen of a ribbon mic, sufficiently build up in the magnetic
gap and rub against the ribbon, causing distortion, electrical shorts or
tearing of the ribbon.
AIR TURBULENCE
Avoid exposing the microphone to strong air turbulence. Ribbon microphones can
withstand very high SPL (Sound Pressure Level), but can be damaged by a strong
gust of air or high levels of very low frequency sound waves (from a kick drum
or bass cabinet). This can stretch the ribbon, reducing overall output,
especially at high frequencies.
Take precautions when recording any source that moves air. To avoid damage,
follow “The Hand Test”: put the back of your hand where the mic will be
positioned; if you can feel the moving air, place a pop-filter between the
microphone and the source or simply pull the mic farther back. When recording
kick drums or bass guitar cabinets, angle the microphone so that no air blasts
the microphone directly on-axis from the front or back.
Never blow directly into any microphone to test it. Not only does this force
moisture and dirt into the microphone, strong air movement also can stretch
the ribbon and while it may not break, it nonetheless could significantly
degrade the microphone’s performance. Though the ribbon in your KU4 is
protected by a grille and acoustical fabric, which provides reasonable wind
protection while still allowing good high-end response, take care to avoid
high-wind outdoor environments.
STRAY MAGNETIC FIELDS
Ribbon microphones are fundamentally prone to picking up strong external
magnetic fields generated by light dimmers or nearby power transformers.
Though AEA designers paid much attention to suppressing such sensitivity, it
is still possible that you might encounter this problem. If you should pick up
a hum, try rotating or moving the microphone to find a spot where the hum
disappears, and try eliminating potential sources of stray magnetic fields.
Rotate or move the mic to find the point of peak interference.
The high-performance magnets used in AEA microphones are incredibly strong, and a significant amount of stray magnetic field lines surround the microphone. To prevent data loss caused by magnetic fields, avoid placing the microphone in close proximity to hard drives, credit cards, analog tape, or any other magnetically sensitive items.
MICROPHONE POSITIONING
Always use a sturdy microphone stand with the KU4. Weighing in at around 5lbs,
the KU4 requires mounting on a strong, robust microphone stand with a heavy
base or tripod. Large studio booms with an appropriate counterweight are
recommended to prevent your KU4 from tipping over and crashing, causing injury
to itself, a musician, or a valuable musical instrument.
The integrated cushion mount was designed to keep structure-borne noise transmitted through the microphone stand and the cable away from the low-tuned ribbon transducer. For the shock mount to function as intended, it is important to vertically position the cushion mount off of the mic stand and to rotate the microphone within the yoke, as opposed to rotating the entire mic on the stand. This requires the use of a swivel mount or posi-lock when using a boom arm for positioning the microphone in a vertical configuration. Having the cushion mount reaching out horizontally on a boom will cause inferior vibration isolation and can also distort the cushion mount as time goes by.
APPLICATIONS ADVICE
We actively encourage users to visit AEAribbonmics.com to access our comprehensive collection of in-depth articles and tutorials featuring the KU4, along with a library of audio and video demonstrations of the KU4 in action.
PROXIMITY EFFECT
Proximity effect, a characteristic of all directional microphones, is a rise in low-frequency response at closer working distances. This can be used to superb effect, particularly with deeper vocals to enhance richness and depth. A potential trade-off is reduced articulation resulting from the masking effect on the treble due to “excessive” bass boost.
HOW TO MINIMIZE BLEED
A significant and ever-present challenge in contemporary studio recording is
minimizing “leakage” from nearby instruments into the various microphones. The
deep nulls of ribbon microphones provide good rejection of unwanted sounds,
which also can be beneficial in sound reinforcement situations where
“feedback”
is always a threat. While “gobos” can be effective in isolating performers
from each other, they introduce their own set of problems – not the least of
which are reflections in close proximity to the performers and/or microphones
that result in comb-filter distortions. Because gobos usually are bulky and
occupy valuable floor space, they also inhibit the ability of the musicians to
hear and see each other easily. Such a setup requires complex and often
cumbersome headphone monitor mixes for the musicians.
SUPERCARDIOID DIRECTIONALITY
Because the KU4 has a supercardioid pattern, it has nulls at approximately ±
135° from the principal (front) axis. Projected in three dimensions, these
nulls produce a “cone of rejection” to the rear of the microphone that can be
used effectively to reduce leakage. Simply arrange the musicians so that
nearby instruments are placed in the “null” of their neighbor’s microphone,
and vice versa. Although this does not entirely eliminate the need for gobos,
it can significantly reduce their number.
SPECIFICATIONS
- Operating Principle: Pressure gradient transducer
- Directional Pattern: Supercardioid
- Frequency Range: <30 Hz to >20 kHz
- Maximum SPL: 140+ dB SPL above 200 Hz for 1% third harmonic
- Sensitivity: -52dBV (2.5 mV/Pa) (at 1 kHz into unloaded circuit)
- Output Impedance: 300 Ω nominal
- Load Impedance: 1.5 kΩ or greater
- Phantom Power: Not required or recommended
- Polarity: Pin 2 high for positive pressure on front of mic
Off Axis Response
- Relative Output: -12 dB at 180°
- Angle of Max Rejection: 135°
Transducer Element
- Material: Pure aluminum corrugated ribbon
- Thickness: 1.8 μm
- Width: 0.082 in (2.1 mm)
- Length: 1.25 in (28.6 mm)
Microphone Dimensions
- Height: 12.6 in (32.00 cm)
- Width: 4.6 in (11.68 cm)
- Depth: 3.7 in (9.40 cm)
- Weight: 4.7 lb (2.15 kg)
- Ship Weight: 7.0 lb (3.20 kg)
- Connector: XLR-3M wired to a 1.5m captive cable
- Accessories Included: Storage case, stand adapter, user manual
POLAR PATTERN
FREQUENCY RESPONSE
- Data below 200 Hz omitted due to measuring room restrictions
- 0 dVB is equivalent to 2.5 mV/Pa (-52 dBV)
- Normalized to 0 dB at 1kHz. 1/3 octave smoothing
AEARIBBONMICS.COM | @RIBBONMICS | INFO@RIBBONMICS.COM | 800-798-9127
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>