VENTUM NS1 Aero Road Bike User Manual
- June 9, 2024
- VENTUM
Table of Contents
NS1 Aero Road Bike User Manual
WELCOME
Congratulations on your purchase of the Ventum NS1, your Aero All-Road
Performance Bike! Get ready to experience a bike that is totally unlike any
other on the road today. Your new Ventum NS1 combines forward thinking design
with the most advanced technologies available, to shatter the notion that a
road bike can be either lightweight or aerodynamic.
This document will guide you through the process of setting up your new bike
and getting out on the road. Of course, if you have any questions or if we can
be of assistance in any way, please contact the Ventum Concierge team at
support@ventumracing.com. Before you hit
the road, please also take a moment to register your bike purchase via our
website.
FRAME DIAGRAM
Please carefully inspect the image. It gives you a thorough break down of the names of the tubes that the frame/ fork consist of and the components that this bike uses. Please refer back to this image as needed.
| 1 | Top Tube |
|---|---|
| 2 | Fork |
| 3 | Head Tube |
| 4 | Down Tube |
| 5 | Chain Stay |
| 6 | Seat Stay |
| 7 | Seat Tube |
| 8 | Seat Post |
| 9 | Saddle |
| 10 | Seat Post Clamp |
| 11 | HeadSet Spacer |
| 12 | Stem |
| 13 | Handle Bar |
| 14 | Brake Lever |
| 15 | Rear Derailleur |
| 16 | Cassette |
| 17 | Chain |
| 18 | Crank |
| 19 | Front Derailleur |
| 20 | Brake Caliper |
| 21 | Brake Rotor |
| 22 | Tire |
| 23 | Rim |
UNBOXING
Remove the parts box and support cover
Remove the top tube foam blocks and shifter blocks
WHEEL REMOVAL
Remove the straps and foam blocks from the wheels
Remove the wheels from the box and remove the hub guards
SEAT POST INSTALLATION
-
Detach the seat post and remove the protective foam
-
Undo the strap around the bottom bracket
-
Plug Di2 cable into seat post battery, you should hear a click.
-
Insert the seat post into the frame. Ensure the minimum insertion depth of 10 cm is achieved.
-
Torque the seat post clamp bolt to a minimum of 6 N.m. Temperature, moisture, and contaminants can affect the seat post clamp. If necessary, it can be torqued up to 8 N.m.
NOTE: To remove or adjust the seat post, loosen the seat post clamp bolt.
It is not necessary to remove it from the clamp entirely. Simultaneously tap the tail and nose of the saddle with your hands to disengage the clamp’s grip on the seat post and permit adjustment. Push or pull the seat post as required to achieve the desired saddle height.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.
FRAME UNBOXING
Remove the straps from the handlebar
- Lift the frame out of the box
- Detach the strap and foam block from the crank arm
WHEEL INSTALLATION
Remove the spacers from the brake calipers
Install the wheels ensuring the rotor lines up between the brake pads
Secure the wheels by re-installing the thru axles. Torque to 12 N.m.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.
FINAL CHECKS & ROAD TEST
- Install your pedals as per the manufacturer’s instructions.
- Check the tire pressure and inflate as per the manufacturer’s recommendation.
- Adjust the saddle height as necessary. Ensure the seat post minimum insertion depth of 10 cm is achieved.
- Put on your shoes and helmet and take your new bike out for a road test. Always wear a helmet when you ride your bicycle.
- Check the operation of the brakes, derailleurs, and steering.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.
ENJOY YOUR NEW RIDE!