NOVALUX 55594 4-ft 22W-30W/40W LED Strip Retrofit Instruction Manual
- June 4, 2024
- NOVALUX
Table of Contents
NOVALUX 55594 4-ft 22W-30W/40W LED Strip Retrofit
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION.
Please read the instructions before you install and use the luminaire.
- WARNING, CAUTIONS, AND OPERATING INSTRUCTIONS
- Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for the installation of the LED retrofit kit. Check for enclosed wiring and components. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
WARNING: RISK OF FIRE OR ELECTRICAL SHOCK
- Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
- Turn off the power when you perform any maintenance.
- Verify that the supply voltage is correct by comparing it with the luminaire label information.
- All wiring connections should be capped with UL-approved wire connectors.
CAUTION: RISK OF INJURY
- Avoid looking directly at the light source for prolonged periods of time while it is on.
- Account for small parts and destroy packing material, as these may be hazardous to children.
- Risk of burn. Disconnect power and allow the fixture to cool before changing bulb or handing fixture.
- Green ground screw provided in proper location. DO NOT RELOCATE.
- Minimum 90° supply conductors.
- Suitable for Dry or Damp locations.
KIT INCLUDES
Part| Quantity
4FT| 8FT
Retrofit Housing| 1| 2
Installation Bracket| 2| 3
Lens| 1| 2
Installation Instructions| 1| 1
Label| 1| 1
WARNING – TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER
THE KITS HAVE BEEN TESTED, FULLY AND PROPERLY MOUNTED IN A FIXTURE AS SIMILAR AS POSSIBLE TO THE KIT’S INTENDED USE. THE UNIVERSAL DESIGN FITS MOST 4.25” TO 5.25” WIDE T8/T12 FLUORESCENT STRIPS.
INSTALLATION STEPS
-
Shut off power to the existing fixture. Disconnect the black and white power supply wire (and ground wire if equipped) to the existing ballast.
-
Remove the original lamps from the existing fixture. (Recycle lamps according to state-specific recycling guidelines.)
-
Remove the ballast cover, ballast, socket bars, and wiring. (Fig. 1)
WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER! BEFORE INSTALLING OR SERVICING. -
Install retrofit brackets using screws. (Fig. 2)
-
Make electrical connections per the wiring diagram.
-
Install LED Retrofit Assembly.
-
Install lens – After installation check to make sure the lens is completely secure, snapped inside the entire length of the lamp body, and fitted under the end cap. Gently pull down on the lens to ensure it does not shift.
-
Restore power to fixture. (Fig. 3)
FIELD ADJUSTABLE WATTAGE & CCT (Fig. 4)
The end user may adjust the color temperature and lumen output,
respectively, by the two slide switches integrated into the side of the
fixture. Each switch has 3 options (left, middle, and right ), each position
corresponds to 1 of 3 color temperatures (Warm White, Cool White, and Sky-
Brite®) and 1 of 3 wattages, which can be adjusted to the desired combination.
Default Settings for 55594: 40W, 5000K Default Settings for 55597: 75W, 5000K
- Switches are located on the LED Module driver box.
- Select a wattage and color temperature by sliding
- left or right respectively to the desired value.
-
P.Q.L., Inc.
-
2285 Ward Avenue
-
Simi Valley, CA 93065
-
Specifications are subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>