Keenstone B0BYHBFXX4 2.5H Fast Charging Dock for Oculus Quest 2 with 2 Rechargeable Batteries User Manual
- June 9, 2024
- Keenstone
Table of Contents
Keenstone B0BYHBFXX4 2.5H Fast Charging Dock for Oculus Quest 2 with 2
Rechargeable Batteries
Safety Instructions
Read all the instructions before using the product, refer to the information on the exterior bottom enclosure for electrical and safety information before installing or operating the product.
- Store the product in a cool and dry place.
- Do not store the product in a hot or humid environment.
- Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
- Operating temperature should be between 0°C to 35°C.
- Do not disassemble the product.
- Do not leave or dispose of the product in both extremely low air pressure and extreme heat such as sunshine, fire, or the like.
- Do not clean the product with harmful chemicals or detergents.
- Misuse, dropping or excessive force may cause product damage.
- When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical system separate from each other.
- Be aware the discharged battery may cause fire or smoke, so tape the terminals to insulate them.
- Do not subject the product to mechanical shock, crushing, or cutting.
- Do not short-circuit the product or be short-circuited by other metal objects.
- Do not use any cell or battery which is not designed for using with the equipment.
- To reduce the risk of injury, close supervision will be necessary when this product is used near children or keep the product out the reach of children.
- Do not put fingers or hands into the product.
- Do not use the product in excess of its output rating. Overload output above rating may result in a risk of fire or injury to persons.
- Do not use the product that is damaged or modified. It may exhibit it may result in fire, explosion, or injury.
- Switch off the device when not in use.
- Do not install this equipment in a confined or building-in space such as a bookcase or similar unit, but remain in good ventilation conditions at an open site.
- The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
- Attention should be drawn to the environment aspects of battery disposal.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremly low air pressure may result in an explosion or the leakage of flammable liquid or gas.
CAUTION:
- Risk of fire or explosion may happen the battery is replaced by an incorrect type.
- Replace only with the same or equivalent type.
- Rechargeable Ni-MH battery mode: Ni-MH AA 1800mAh 1.2V.
WARNING:
- Use only power supplies listed in the user instructions.
Service
If you encounter any technical problems, Please contact:
Email:Support@keenstone.com
We provide a 12-MONTH WARRANTY plus online responsive customer service
Package Contents
- Charging Dock for Quest 2 VR Headset and Controllers Fully charge your headset and controllers at the same time
- USB-C to USB-C Cable
- Pair with the Power Delivery charger for faster charging
- USB-C Charger
- Fast-charging Power Delivery charger
- Battery Charging Doors
- Safely charge your controllers without removing the batteries
- Magnetic USB-C Headset Connector
- Connect your headset to the charging station to enable wireless charging
- Rechargeable AA Batteries
- Specially designed for Quest 2 Touch controllers
- Email: Support@keenstone.com
Product Diagram
- Charging dock for headset
- USB-C input port
- Magnetic output connector
- Charging dock for controllers
- Power LED indicators for headset
- Power LED indicators for controllers
- Charging pin
- Magnetic USB-C plug
- Replacement battery door
- Rechargeable batteries.
Specifications
| USB-C Input | DC 5V/9V |
|---|---|
| Magnetic USB-C Output Max | 5.0VDC 3.0A, 9.0VDC 2.0A |
| Left Controller Charging Port | 1.SVDC0.9A |
| Right Controller Charging Port | 1.SVDC0.9A |
| Charging Time | Appr. 2.5 hours |
| Rechargeable Battery Capacity | DC 1.2V / 1800mA x2 |
How to Use
- Insert the magnetic USB-C plug into the USB-C charging port of your headset.
- Place your headset into the charging dock and make sure that the magnetic USB-C plug adheres to the magnetic output connector.
- Remove the original battery door and alkaline battery from control le rs.
- Install the rechargeable battery with correct polarity, and make sure that the 2 bare metal sheets align with the outer frame of the battery compartment. Close the battery door and place the controllers into the charging dock.
- Connect the charging dock to the power supply by using the provided USB-C charging cable and charger.
- The power LED indicators will turn on.
If you use a charger with an output of s~1sw, the charging dock will give priority to charge the headset. If the output of the charger is less than SW, the charging dock won’t work.
LED Light Guide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>