Lucci decor 018370 Olive 1 Light Pendant Instruction Manual

: June 9, 2024
: Lucci decor

Table of Contents

018370 Olive 1 Light Pendant
Product Information
Installation Requirements
Installation Instructions
Safety Tips
Warranty
Installation Requirements
Installation Directions
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

018370 Olive 1 Light Pendant

Product Information

The OLIVE 1 LIGHT PENDANT is an indoor luminaire that comes in four SKUs: 018370, 018371, 018372, and 018373. It has a rated voltage of 220-240V~ 50Hz and a maximum wattage rating of 45W. The luminaire is available in two colors: white and black. It has a Class I protection class and an ES/E27 lamp holder. The canopy
dimensions are H:50mm Dia:110mm, and the luminaire dimensions vary depending on the SKU.

Installation Requirements

The luminaire should only be used indoors.
The mounting point must support twice the weight of the luminaire.
Do not install the luminaire in the direct line of an air vent/system.
If installing the luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriate moisture barrier is used.

Installation Instructions

Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
Determine the suspension length required for your installation location. If the length of the suspension cord requires adjustment, loosen the cord anchorage inside the canopy and adjust the length of the suspension cord. Tighten the cord anchorage, taking care not to overtighten and damage the cord.
Remove the mounting bracket from the canopy by loosening the screws on the sides.
Use the mounting bracket as a template to mark the screw hole positions on the ceiling.
Pull the mains supply wire down from the ceiling and through the mounting bracket hole.
Install the mounting bracket onto the ceiling by using appropriately sized mounting screws and anchors. Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment.
Connect the mains supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed.
Install the canopy back onto the mounting bracket.
Secure the canopy by tightening the screws on the sides.
Install a globe (not included) into the lamp holder. Do not exceed the maximum wattage rating.
Check the installation is complete and the globe has been installed into the lamp holder. Switch the power back ON to the circuit you have been working on. Switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
This luminaire is a Class I product and must be earthed during wiring and installation.

To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

This luminaire is covered by a 12-month warranty. The warranty is from the date of purchase, not the date of installation.
If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

This luminaire must be assembled and installed by a licensed electrician.
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
- E. g. AS/NZS 3000 Electrical Installations.
This luminaire is a Class I product and must be earthed during wiring and installation.
Do not exceed the maximum wattage rating.
Select a suitable location for installation:
- This luminaire is suitable for indoor use only.
- The mounting point must support 2 times the weight of the luminaire.
- Ensure the luminaire is not installed in the direct line of an air vent/system.
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

Installation Directions

FIGURE A

Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
Determine the suspension length required for your installation location. If the length of the suspension cord, requires adjustment, loosen the cord anchorage inside the canopy and adjust the length of the suspension cord. Tighten the cord anchorage, take care not to overtighten and damage the cord.

FIGURE B

Remove the mounting bracket from the canopy by loosening the screws on the sides.
Use the mounting bracket as a template to mark the screw hole positions on the ceiling.
Pull the mains supply wire down from the ceiling and through the mounting bracket hole.
Install the mounting bracket onto the ceiling by using appropriately sized mounting screws and anchors. Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment.
Connect the mains supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed.

Mains Supply Wire

Earth – Yellow/Green
Neutral – Blue or Black
Live – Brown or Red

Luminaire Wire / Terminal block

Yellow/Green or
Blue or N
Brown or L

NOTE: This luminaire is a Class I product and must be earthed during wiring and installation.

Install the canopy back onto the mounting bracket.
Secure the canopy by tightening the screws on the sides.
Install a globe (not included) into the lamp holder. Do not exceed the maximum wattage rating.

FIGURE C

Check the installation is complete and the globe has been installed into the lamp holder. Switch the power back ON to the circuit you have been working on. Switch on the luminaire to test and enjoy your new lighting product.

018370 Olive 1 Light Pendant 1 Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from liquids and hazards.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.