milwaukee M18 BLID2 Brushless Impact Driver Instruction Manual
- June 9, 2024
- Milwaukee
Table of Contents
Nothing but HEAVY DUTY® M18 BLID2
Original instructions
M18 BLID2 Brushless Impact Driver
Picture section
with operating description and functional description
Remove the battery pack before starting any work on the machine.
Handle (insulated gripping surface)
TECHNICAL DATA CORDLESS IMPACT SCREWDRIVER
M18 BLID2
Production code…………………………………… 4679 96 02……000001-999999
No-load speed ………………………………..0-1700 min-1
Impact range ………………………………………….0-1500 min-1
Max. diameter bolt / nut ……………………………….M14
No-load speed ………………………………………… 0-2600 min-1
Impact range …………………………………………. .0-3400 min -1
Max. diameter bolt / nut ……………………………….M14
No-load speed ………………………………………… 0-3400 min -1
Impact range …………………………………………..0-4200 min -1
Max. diameter bolt / nut ………………………………. M14
Tool reception……………………………………………….. HEX 1/4″ (6,35 mm)
Torque……………………………………………………………………………………………… 180 Nm
Battery voltage……………………………………………………………………………………… 18 V
Weight according EPTA-Procedure 01/2003 (without battery) ……………………. 1,0 kg
Weight according EPTA-Procedure 01/2003 (4.0 Ah … 6.0 Ah)……………………………………… 1,7
kg
Weight according EPTA-Procedure 01/2003 (9.0 Ah)………………………………… 2,1 kg
Recommended ambient operating temperature……………………………….. -18…+50 °C
Recommended battery types ………………………………………………………………………… M18B…, M18HB…
Recommended charger……………………………………………………………………………………. M12-18C, M12-18AC,
M12-18FC, M1418C6
Noise information
Measured values determined according to EN 62841
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ………………………………………. 94,43 dB (A)
Sound power level (Uncertainty K=3dB(A))………………………………………… 105,43 dB (A)
Wear ear protectors!
Vibration information
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Impact tightening of fasteners of the maximum capacity of the tool
Vibration emission value ah.,0……………………………………………………………………………………………………………………………
14,95 m/s²
Uncertainty K= ………………………………………………………………………………….. 1,5 m/²
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings, instructions, illustrations and specifi
cations provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
IMPACT DRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners contacting a
„live“ wire may make exposed metal parts of the power tool „live“ and could
give the operator an electric shock. Wear ear protectors. Exposure to noise
can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
- when changing tools
- when setting the device down
Sawdust and splinters must not be removed while the machine is running.
When working in walls ceiling, or floor, take care to avoid electric cables and
gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage. Remove the battery pack before starting any work on
the machine. Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors offer to retrieve old batteries to
protect our environment. Do not store the battery pack together with metal
objects (short circuit risk). Use only System M18 chargers for charging System
M18 battery packs. Do not use battery packs from other systems. Never break
open battery packs and chargers and store only in dry rooms. Keep dry at all
times. Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly for
at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fire, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in fl
uid or allow a fl uid to fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen nuts and bolts
wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
“Technical Data” fulfills all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/ EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-10-27
**** Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under “Technical Data” fulfills all the relevant provisions of the
following egulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as
amended), S.I. 2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-2:2014
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-10-27
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
OPERATION
Note: It is recommended after fastening to always check the torque with a
torque wrench.
The fastening torque is affected by a wide variety of factors including the
following.
- State of battery charge – When the battery is discharged voltage will drop and the fastening torque will be reduced.
- Operation at speeds – Operating the tool at low speeds will cause a reduction in fastening torques.
- Fastening position – Holding the tool or the driving fastener in various angles will affect the torque.
- Drive accessory/socket – Failure to use the correct size accessory or socket, or a non-impact rated accessory may cause a reduction in the fastening torque.
- Use of accessories and extensions – Depending on the accessory or extension fi tment can reduce the fastening force of the impact wrench.
- Bolt/Nut – Fastening torques may differ according to the diameter of the nut or bolt, the class of nut/bolt and the length of nut/bolt.
- Condition of the fastener – Contaminated, corroded, dry or lubricated fasteners may vary the fastening torques.
- Condition and base material – The base material of the fastener and any component in between the surfaces may effect the fastening torque (Dry or lubricated base, soft or hard base, disc, seal or washer between fastener and base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it will become.
To help prevent damaging the fasteners or workpieces, avoid excessive
impacting.
Be particularly careful when impacting smaller fasteners because they require
less impacting to reach optimum torque.
Practice with various fasteners, noting the length of time required to reach
the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the head of the
fastener affects the degree of tightness.
The torque required to loosen a fastener averages 75% to 80% of the tightening
torque, depending on the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a relatively light torque and
use a hand torque wrench for final tightening.
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully
charged.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% – 50% charged condition Every six months of
storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 2 seconds and then
the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could
become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
- The user can transport the batteries by road without further requirements.
- Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts. When transporting batteries:
- Ensure that battery contact terminals are protected and insulated to prevent short circuit.
- Ensure that battery pack is secured against movement within packaging.
- Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max- Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
| CAUTION! WARNING! DANGER!
---|---
| Remove the battery pack before starting any work on the machine.
| Please read the instructions carefully before starting the machine.
| Do not dispose electric tools, batteries/rechargeable batteries together
with household waste material. Electric tools and batteries that have reached
the end of their life must be collected separately and returned to an
environmentally compatible recycling facility. Check with your local authority
or retailer for recycling advice and collection point.
n0| No-load speed
n| Impact range
V| Volts
****| Direct current
| European Conformity Mark
| British Confomity Mark
| Ukraine Conformity Mark
| EurAsian Conformity Mark.
Copyright 2020
Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>