Stinger SPXDUBKIT Dynamic RGB LED Strip Kit User Manual

Stinger SPXDUBKIT Dynamic RGB LED Strip Kit

DYNAMIC RGB LED STRIP KIT, 6 PIECE
Before you start, review the directions completely.

If your vehicle is not pre-wired for external lighting, You may need the following:

• In-line Fuse Holder (SPXATC16 or similar)
• 3Amp Fuse
• 2 Strand Primary Wire
• Wire Connectors / Solder
• WireCover

Optional:

• Switch
• Relay

WHAT’S INCLUDED

• 6 x LED Strips
• 6 x LED Extension Cables (10ft)
• 1 x Bluetooth RGB Control Module with connection for HEIGHlO
• 1 x RF Remote Control
• 18 x Mounting Brackets
• 43 x Mounting Screws
• 1 x 1.5 x 2.5 Adhesive Pad
• 14×8″ Zip Ties

MOUNTING LED STRIP LIGHTS

1. Determine a location for the RGB module

2. For correct light pattern flow, mount each light strip with the male connector end facing the front of the vehicle.

3. Connect each light to the extension harness by matching both arrows correctly and tightening the locking nut.
   NOTE: Avoid mounting the module in locations that get extremely hot or wet.

4. Mount the strip lights using the supplied mounting hardware. Each strip light has a 3M adhesive to hold the strips in place. Strip lights and extension cables should be mounted in a location where they will not come in contact with the exhaust, suspension, tires or road surface.

5. Route and connect the light cables to the RGB module in a daisy chain connection. Start with the Front lights, then to the middle lights, and then to the rear lights.

NOTE:
Make sure the strips with the single connec­tion are used for the rear.

Connections

Connecting strip lights Leff side

1. RGB module left female connector to left male extension connector
2. Left front 21″ strip light male connector to female extension connector
3. Left front 21″ strip light female connector to male extension connector
4. Left side 60″ strip light male connector to female extension connector
5. Left side 60″ strip light female connector to male extension connector
6. Left rear 21″ strip light male connector to the female extension connector

Right side

1. RGB module right female connector to right male extension connector
2. Right front 21″ strip light male connector to female extension connector
3. Right front 21″ strip light female connector to male extension connector
4. Right side 60″ strip light male connector to female extension connector
5. Right side 60″ strip light female connector to male extension connector
6. Right rear 21″ strip light male connector to female extension connector

OVERVIEW

WIRING DIAGRAMS

Diagram 1:
Wiring direct to power and using an App to turn on/off. Must add 3 AMP fuse on RED 12V+wire.

Diagram 2:
Wiring with a switch. You can add a new dedicated switch or use an existing light switch that outputs 12V+ when ON. You will need to add a 3 AMP fuse on the RED 12V+ wire which also requires a 12V relay.

Note:
When wired to a switch, the RGB controller will default to the last mode/color used. No need to access the app.

HEIGH10 connection:
Connect the Sirius XM harness to the HEIGHlO Radio Module, then connect the 4-pin male connector of the LED module to the female connector of the HEIGHl0 Sirius XM harness.

If your HEIGHlO is missing the harness or has the wrong connector you will need to purchase the optional harness (SE-SXMHAR)

NOTE:
The lighting module will still need separate power and ground when connecting SE-SXMHAR.

Radio Module

GET THE APP

Scan the QR Code, or visit Google Play or iTunes to download the Stinger Lighting opp. Once the app is installed, power up the RGB Module and open the opp. The module should auto-connect and be listed in the device list. And Dan says Let There Be Light.

SCAN for Apple iOS and Android App

LIMITED WARRANTY

Stinger warrants this product to be free of defects in materials and workmanship for a period of one ( 1) year from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with the new or re-manufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, and misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty informa­tion for these products must contact that country’s reseller for information.

When adding multiple light kits together you will need to adjust the pixel count using the enLIGHTl 0 phone app.

Below is the pixel count for each part and on page 2 you will find the Steps and the Pixel Calculator.

• Each SPXDBTC has a pixel count min and max
• Minimum30
• Maximum 1024
• Rock Lights = 4 pixels per Rock Light

For example:

• 1 SPXDK4 (4 Rock Lights) = 16 pixels. (App supports min 30 pixels)
• 1 SPXDK8 (8 Rock Lights) = 32 pixels.
• Whips and Light Strips are treated as left/right pairs so pixel count is for two units.

For example:

• 2 SPXDW4 (Whips) = 108 Pixels total.
• 2 SPXD5 (Light Strips) = 100 pixels total.
• If you were to have three or four Whips you would enter 108 x 2 = 216 pixels.
• If you were to have three or four Light Strips you would enter 100 x 2 = 200 pixels.

Product Pixel Count

• SPXDK4
  • 4 Rock Light Kit = 16 pixels
  • App is preset to 30 pixels
• SPXDKS
  • 8 Rock Light Kit = 32 pixels
  • App is preset to 32 pixels
• SPXDE4
  • 4 Add on Rock Lights = 16 pixels
  • Add 16 pixels for each kit
• SPXD5
  • 5 Meter LED Strip = 100 pixels
  • Add 100 pixels for one or two strips
• SPXDUBKIT
  • 6 LED Light Strip Kit = 50 pixels
  • App is preset to 50 pixels
• SPXDW4
  • 4ft Whip = 108 pixels
  • Set App to 108 pixels for one or two Whips

Setting

• Step 1.
  Open the enLIGHTl O opp on your phone.

• Step 2.
  Open the Settings menu.

• Step 3.
  Click on Chasing Setting.

• Step 4.
  Click on the device. The device should now be highlighted in blue. If you have a kit the device name will have a preset pixel count (SPXDK4 = 30, SPXDK8 =32, SPXDUBKIT = 50).

• Step 5.
  Enter the number of pixels you want and press enter.

• Step 6.
  Go to the Mode page and turn the connected device off and then on by pressing the Green icon.

Pixel Calculator

• Rock Light = 4 pixels each
• LED strip per 2 inches = 1 pixel

For example:

• 12 Inch strip = 6 pixels

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>