Estella 236ECEGOD On Demand Espresso Grinder User Manual
- June 10, 2024
- Estella
Table of Contents
236ECEGOD On Demand Espresso Grinder
Product Information
- Product Name: On-Demand Espresso Grinder
- Model Number: 236ECEGOD
- Product Code: 3058215
- Date: 08/2022
NOTE: Save these instructions for future reference.
Product Usage Instructions
Safety Warnings
- Ensure that the wall receptacle is grounded. Do not use extension cords or wall adapters.
- The grinder must be screwed into place to the grind selector.
- This machine should only be used by qualified personnel.
- Do not allow anyone under the age of 18 to use this machine.
- Do not unplug the grinder by pulling on the cord.
- Unplug the grinder before reaching in for any reason.
- Beware that grinder may continue to spin for a short period of time after turning off the machine.
- Do not operate with wet hands.
- Do not allow liquid to come into contact with the grinder.
- Only put espresso beans into hopper.
Troubleshooting
- Make sure that the handle on the grinder is correctly screwed in place and that it stays within the lines on the grind selector.
If the grinder is not working or tripping:
First check the grind selector. It is possible that beans got stuck in the
grinder – to check, turn the handle to a more coarse setting and turn on
machine. If this does not work, try using the Automatic Power Failure
Installment Button. This is located next to the power button, and can be used
when the grinder has tripped or has stopped working. This will reset the
grinder.
Installation
- Make sure grinder is sitting on a flat surface.
- Before plugging in the grinder, make sure the voltage of the electric supply match machine ratings.
- If hopper becomes detached, make sure to securely fit it into the grinder. The handle will need to be screwed into place to the grind selector.
Wall receptacle must be grounded. Do not use extension cords or wall adapters.
Programming
- You can program both the one cup and two cup buttons located on the setting panel. Doing so will allow the machine to run for the amount of time selected, when the button is pressed.
- To program time (in seconds), click on either the one cup or two cup button and adjust the time to the desired amount using the minus (-) and plus (+) buttons.
- When you reach the desired time, hit the start button to begin grinding.
- Decrease time (in seconds) of how long the grinder is grinding beans.
- Increase time (in seconds) of how long the grinder is grinding beans.
- The one cup button is for the first setting, which you can program to the amount of time the machine will grind beans for.
- The two cup button is for the second setting, which you can program to the amount of time the machine will grind beans for.
- The continuous run button will continue to run as long as the button is held down. The grinder will stop when the button is released.
Note: The continuous run button will continue to run as long as the button is held down. The grinder will stop when the button is released.
Operation
- Ensure that the hopper is securely fitted to the top of the grinder.
- Close the slide underneath the hopper.
- Fill the hopper with espresso beans and secure the lid.
- Open the slide to allow beans to fall into the grinder.
- Turn the power switch to the on position.
- Put the portafilter below the doser, and make sure to hold in place during the grinding process.
- To start grinding, select the button for either the one cup or two cup setting and hit start, or manually grind by pressing the arrow button.
- The grinder will grind beans until the selected time runs out or you can press the ‘Start’ button again to stop the grinder.
If grounds are not dispensing ensure that properly dried espresso beans are being used. Make sure to pull dispensing lever entire way forward and then allow to release back to its original position.
Note: To adjust coarseness of grounds thread the adjustment handle into the grind selector and rotate to desired position. Only adjust coarseness while the machine is on. Please note that adjusting the grind will change the amount dispensed.
Cleaning
- Close slide and pull off the funnel from the machine.
- Use a vacuum cleaner to get any loose grounds out of the machine.
- Wash the funnel with nonabrasive soap and water.
- Make sure to dry the funnel completely by air drying.
- Use a brush to sweep off any loose grounds and dust that are in funnel, doser, and base.
Caution: Do not get water/soap in the base and burr area.
Parts List
- Grind Adjustment Spring
- Grinding Machine
- Gear Plate Group
- M4 Screw
- Grinding Machine Anchor Screw
- M4 Screw
- Cone-Shape Coffee Beans Pouring Trough
- Grinder Selector
- Adjustment Stick
- Grind Adjustment Abut Screw (M4 Screw)
- Funnel
- Funnel Lid
- Cooling Fan
- Foundation Lid
- Footpad
- Power Button
- Automatic Power Failure Installment Button
- Funnel
- Setting Panel
- Handle Frame
- Controller
- Slide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>