Hangzhou Fanhan Technology Co Ltd LJH10 Starlight Security Camera User Manual
- June 10, 2024
- Hangzhou Fanhan Technology Co Ltd
Table of Contents
Hangzhou Fanhan Technology Co Ltd LJH10 Starlight Security Camera
This Quick Start Guide has been translated into 4 other commonly used
languages for users from North America and Europe (Spanish, French, Italian,
and German). We refrain from printing these large manuals in an effort to
limit our impact on the environment.
Scan the code on the right to read different versions of this Quick Start
Guide on how to operate your cameras.
IN THE BOX
*For customers who have purchased a 2-pack of this product, each component below will be doubled (except the USB cable, power adapter and the quick start guide).
-
VIRTAVO Camera*1
-
USB Cable*1
-
USB Adapter*1
-
Screw Kit*1
-
Quick Start Guide*1
-
3M VHB Sticky Adhansive pad*1
-
Nut*1
-
Round Adapter plate *1
-
Camra Mount Holder*1
PRODUCT OVERVIEW
|
SETTING UP THE SYSTEM
- Download the Home V app and create an account.
- Switch the power button on to wake up the camera.
- Press the Sync button for about 5 seconds until you hear a ‘Ou’ sound with the red light flashing.
- Go to the Home v app, then add your device by tapping on the ‘+’ button; follow the app instruction to finish the setup process.
MOUNTING THE CAMERA
Outdoor Installation Note
For outdoor use, installation in a sheltered location is recommended. Please
place the camera upward to avoid rain or snow getting into the device. Avoid
installing the cameras where there are thick walls or obstructions between the
cameras and the router.
You may mount your cameras on a wall ceiling or counter Follow the 4 steps
below·
-
Mark the positions of the screw holes on the mounting surface, then use a 1/4″ drill bit to drill holes and place the round adapter plate on the surface with anchors and screws (included) as needed.
-
Place the nut onto the round adapter plate.
-
Press the camera mount holder onto the adapter plate, then rotate the nut clockwise to the mount holder.
-
Vertically place the camera on the camera mount holder, adjust the angle of the cameras until the desired view is set. Rotate the nut to secure the camera.
*Note: to install the camera on smooth surfaces, use the sticky adhesive
pad (included) to stick the round adapter plate on the surface, then follow
the other 3 steps above.
CHARGING
| Battery status light | Charging: Steady Red |
|---|
Fully Charged; Steady Green
Battery status light| 7-8 hours(Q.100%)
SAFETY STATEMENT
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
(4) Consult the dealer or an experienced radio/ TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/ mobile exposure condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
This product is designed and manufactured with high-quality materials and
components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling help protect natural resources, human health and
the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you brought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1 )this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.
H.265/HEVC Video Standard
Covered by one or more claims of the HEVC
patents listed at
patentlist.accessadvance.com.
LIMITED ONE YEAR WARRANTY
Puwell Technology Inc. warrants this product to be free of defects in
materials or workmanship for one year. This warranty does not include damage
resulting from accidents or misuse. Damage from unauthorized service or
modification of the product or of any furnished component will void this
warranty in its entirety.
This warranty is expressly in lieu of all other warranties, expressed or
implied, including any warranty, representation, or condition of
merchantability or that the products are fit for any particular purpose or
use, and specifically in lieu of all special, indirect, incidental or
consequential damages. To obtain service/replacement, please contact
support@virtavo.com. Please allow up to seven
(7) business days for your replacement to be processed.
CUSTOMER SERVICE
Contact us
support@virtavo.com
@HomeVIRTAVO
@HomeVIRTAVO
