equip 650610 32-65 Inch Motorized TV Tabletop Stand Installation Guide

equip 650610 32-65 Inch Motorized TV Tabletop Stand Installation Guide

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.

  CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Package Contents

Installation Instruction

Note: Insert 2 A44 batteries(not included) into the controller prior to adjust the TV Stand Adjust the height by pressing the “ .” and “ ” buttons on the remote control. If the TV Stand fails to rise or lower, please match code between TV Stand and the remote control by following the instruction below.

Pairing the Remote to the Mount
STEP1: When the mount is powered on, press the small button on the control box with a paper clip or pencil as shown. The unit will emit a beep, indicating that the control box is on standby for program coding.
STEP2: Press the “ “button on the remote control, and you will hear repeated beeps for approximately 10 seconds indicating that the remote control is being programmed. The unit will emit a beep again indicating success.

Once you have the TV Stand in position, unplug the power cord and attach the power adapters to the position on the base as shown in the illustration at the right.

The product is powered by electricity. In order to avoid burns, fire and electric shock and make sure the safe and correct use of the system and maintain the longevity of the overall construction and the built-in electronics, please read the instructions carefully.

  Warnings

• This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge must not use the appliance, unless they’re under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons.
• Don’t leave the cords or plug unorganized in order to prevent tripping hazards.
• Any attempts to reconstruct the construction aren’t allowed.

  Electrical Safety Instructions

• The appliance is only to be used with the power supply unit provided with the appliance. Alterations of the given power unit aren’t allowed.
• Never operate the system with a damaged power supply cord or plug. If any parts is damaged, please contact your service agent of purchase for a replacement.
• Never operate the system if it’s in moist environment or its electrical components has contact with liquids.
• Don’t clean the product while the power is still connected.
•  Don’t disassemble or replace components while the power is still connected.
• Unplug the appliance when the system isn’t in use, and place the power plug out of children reach.

Remote Control User Guide

1. UP/DOWN ARROWS
   Press and hold the ”  ” button to raise the Mount. Press and hold the”  button to lower the Mount. Note: Remove all surrounding items prior to adjusting the Mount height.

2. Memory Setting
   Long press the  ”  button for 3 second untill you hear a beep indicating that thr current position. The current  position has been saved to different position.

3. Recall Memory
   Press the  ” corresponding button “ ” or button for 3 seconds until you hear a beep, indicating that the memory. The “ ” „ ‘ buttons can each store ” button and the mount will automatically get to the position saved in the If

4. Default Setting
   Short press the “ ” button and the mount will automatically retract to the lowest position. To stop it, press the is  ” button again.

5. Reset Mode
   Long press the  button for 3 seconds until you hear a beep, and the mount starts to move downwards. Then the mount will move upwards a little bit when reaching the lowest position and automatically come to a stop. The system resets successfully when the unit emits two beeps.

To Unpair a Remote Control
Press the small button on the control box with a paper clip or pencil as shown. With hearing a beep, hold and press the button for 5 seconds until you hear a beep again. The unpairing process is completed.

Disposal: The product with this mark indicates that this product shouldn’t be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolledwaste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the local recycle service or contact your point of purchase to withdraw the product.

Troubleshooting Guide

1. Can’t operate There are 7 possibilities:
   • Incorrect operation. Check if the unit beeps once after pressing a button. If so, please follow the instructions found in the manual to properly operate the mount.
   • The system of Mount may be error. Check if the unit beeps three times after pressing a button. If so, please reset the system.
   • The system may be overheating. Check if the unit beeps four times after pressing a button. If so, allow the unit to cool down (about 30 minutes).
   • The AC/DC end of the power cord may be unplugged/disconnect from the outlet/mount. Check the connection to ensure the unit is powered.
   • The operating distance may be too far and not in range of the mount. Using the remote control within 30 feet (10m) from the Mounts.
   • The batteries in the remote control may be low or dead. Replace the batteries.
   • The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed. If not, contact your place of purchase for a replacement.
2. The TV mount stops moving during operation and emits a long beep.
   • Remove all surrounding items.
   • The weight of TV may exceed the maximum weight limitation of the mounting system.
   • The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for replacement.
3. The TV mount is making an abnormal noise or sound.
   • Check all power connections and reset the system. If the unit continues to make an abnormal noise, please contact your place of purchase for a replacement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>