CYCPLUS T2 Smart Bike Trainer User Manual

June 10, 2024
CYCPLUS

CYCPLUS T2 Smart Bike Trainer

Product Information

The Smart Bike Trainer, T2, is a high-tech device designed to provide indoor training for cyclists. The product is manufactured by Chengdu Chendian Intelligent Technology Co., Ltd and comes with a warranty of free replacement or repair within one year. The product can be connected to various devices through Bluetooth or ANT+ technology, and the resistance can be controlled through a mobile app or computer software. The product comes with a pre- installed cassette and adapters for thru-axle and quick-release bikes. The product has cooling holes to regulate temperature during prolonged use.

Product Usage Instructions

Quick Start

Visit the official website www.cycplus.com or find Cycplus on Instagram, Facebook, or YouTube for instruction videos, FAQ, and more support.

Notice

  1. Keep children and pets away from T2 while in use.
  2. Keep clear of the motor and moving parts while in use.
  3. The enclosure will heat up when subject to prolonged, extreme use. Always keep the cooling holes clear and plug it in for extreme use to keep the fan working.
  4. Please use the T2 on a stable surface with adjusted leveling feet before use.
  5. Use caution when standing while riding on T2.
  6. Do not install or disassemble the bicycle until T2 completely stops.
  7. Do not use other power sources to power T2.
  8. Please confirm whether the bicycle is installed properly before every ride.

Packing List

The product comes with the following items:

  • T2 (1)
  • 17mm wrench for thru-axle adapter-R (7)
  • Allen key for quick-release adapter-R (8)
  • 8-10 speed cassette spacer (9)
  • Cassette adjustment spacer [5x] (10)
  • Disc brake spacer (11)
  • Oil Disk Brake Pad Spacer (12)
  • Cassette pre-installed (02)
  • Thru-axle adapter-R pre-installed (03)
  • Thru-axle adapter-L pre-installed (04)
  • Quick release adapter-R (05)
  • Quick release adapter-L (06)
  • Quick release (13)
  • AC adapter (14)
  • AC cable (15)
  • Cushioning mat (16)
  • USB ANT+ receiver and Extension Cable (17)

Ground and stabilize T2

  1. Press and hold the lock catch.
  2. Unfold the leg.
  3. Align the lock catch with the notch, and make sure the latch pops up and locks angle of the leg.
  4. Unfold all the legs in turn.
  5. Adjust the leveling feet to balance and stabilize T2. Rotate clockwise to raise and counterclockwise to lower the height of the foot.
  6. Lock the height of the foot by rotating counterclockwise to secure.

Cassette Mounting

If you need to mount another cassette:

  1. For 8/9/10 speed cassettes, put on the cassette spacer with the notch outward before installing the cassette.
  2. For SRAM 12 speed cassettes, an XDR hub will be needed to buy additionally.
  3. Use cassette removal tools to secure the cassette after pushing it into the hub.

Precautions and Disclaimer

  1. Identify the frame type and standard (thru-axle or quick release) before proceeding with installation. Carefully go through the manual and compare it with the actual parts to make sure all of them are complete and properly installed before mounting your bike to T2.
  2. For hydraulic disc brakes, install the pad spacer between the brake pads after removing the rear wheel, to prevent you from accidentally closing the brake without the rotor in place. Please use your own pad spacer if the spacer coming.

Find us on Instagram and Facebook for instruction videos,
FAQ and more support
Instagram: cycplus_ocial
Facebook: cycplus
Youtube: CYCPLUS
Ocial website : www.cycplus.com
After-sales email: steven@cycplus.com

Notice

  1. Keep children and pets away from T2 while in use.
  2. Keep clear of the motor and moving pass while in use.
  3. The enclosure will heat up when subject to prolonged, extreme use. Always keep the cooling holes clear and plug it in for extreme use to keep the fan working
  4. Please use the T2 on a stable surface with adjusted leveling feet before use.
  5. Use caution when standing while riding on T2.
  6. Do not install or disassemble the bicycle until T2 completely stops.
  7. Do not use another power source to power T2.
  8. Please conrm whether the bicycle is installed properly before eve ride

Factory Info

Manufactuerer :Chengdu Chendian Intelligent Technology Co., Ltd
Warranty: Free replacement or repair within 1 year.
After sale email: steven@cycplus.com

Packing List

Ground and stabilize T2

Cassette Mounting
T2 comes preinstalled with a cassette. Read instruction below if you need to mount another one.

  1. For 8/9/10 speed cassettes, put on the spacer before installing the cassette.
  2. For SRAM 12 speed cassettes, an XDR hub will be needed to buy additionally.

Precautions and Disclaimer

  1. Identify the frame type and standard (thru-axle or quick release) before proceeding with the installation. For thru-axle, refer to “2.4 For Bikes with Rear Thru-Axles” for installation. For quick release, refer to “2.5 For Bikes with Quick Release Skewers” for installation. Carefully go through the manual and compare it with the actual pas to make sure all of them are complete and properly installed before mounting your bike to T2.

  2. For hydraulic disc brakes, install the pad spacer between the brake pads(as shown on the right) after removing the rear wheel, to prevent you from accidentally closing the brake without the rotor in place. Please use your own pad spacer if the spacer coming with T2 is not compatible with your disc brake.

  3. T2 is compatible with most quick-release and thru-axle frames including those with disc brake sets. However, there are still a few special frames, because of the shape of the rear fork and the location of the disc brake set, which may not be compatible with T2.
    For bikes with disc brake sets and a chain stay shaped as shown below, they are very likely to be incompatible with T2 and do not force to install.
    For bikes with disc brake sets, make sure the disc brake set is not against the housing of T2. If you and any contact or friction, do not force to install.

  4. Read the manual throroughly and be sure to follow the instructions provided in the manuals when using T2. Don’t hesitate to contact us for suppo and don’t force to install.
    CYCPLUS is not responsible for damage or loss caused by incorrect installation, incompatible bike frame or customer’s forcing installation.

For Bikes with Rear Thru-Axles

  • Insert the quick release skewer into the axle of T2 and install the nut in place, but don’t tighten it yet, in order to install the bike frame.
  • Adjust the shifter untill the chain is on the smallest sprockets of both chain wheel and cassette.
  • Secure the bike with the thru-axle of your bike.
  • Shake the bike frame after installation to make sure the frame is secured to T2.

WARNING!

  1. Failure to properly secure the bike can result in serious properly damage and personal injuries.
  2. Never adjust the quick-release skewer or thru axle while someone is sitting on the bike.
  3. They’re still a few bike frames incompatible with T2. Stop the installation immediately if any abnormalities occur.
  4. Please refer to the disclaimer and don’t hesitate to contact us for any installation problems.

For Bikes with Quick Release Skewers

  • Insert the quick release skewer into the axle of T2 and install the nut in place, but don’t tighten it yet, in order to install the bike frame.
  • Adjust the shifter untill the chain is on the smallest sprockets of both chainwheel and cassette.
  • Align the bike chain with the smallest sprocket of the cassette on T2, and mount the frame to T2.
  • Adjust the lock nut of the quick release skewer, and lift and press the handle frequently at the same time until the pressing resistance is appropriate, then press the handle to secure the skewer.
  • Shake the bike frame after installation to make sure the frame is secured to T2.

WARNING!

  1. Failure to properly secure the bike can result in serious properly damage and personal injuries.
  2. Never adjust the quick release skewer or thru axle while someone is sitting on the bike.
  3. There’re still a few bike frames incompatible with T2. Stop the installation immediately if any abnormalities occur.
  4. Please refer to the disclaimer and don’t hesitate to contact us for any installation problems.

Power Connection

Please use the AC adapter only that comes with T2 to power the device.
The AC cable can be replaced as you like.

Working Status

Working modes
T2 has 2 working modes, unplugged mode and plug-in mode. Plug-in mode can provide a better riding experience. The main functional di erences between the two modes are as follows.

  Unplugged mode Plug-in mode

Signal connection

| When you stat riding, you need to pedal to generate power for wireless connection.

After you stop, the LED indicator may go out, but the stored power will be available for the wireless signal to work for 5 more minutes.

|

Ready to connect Bluetooth and ANT anytime

Downhill and inetia simulation| Unable to simulate downhill and flywheel inetia| Able to simulate downhill and flywheel inetia

Climbing simulation

| When riding at low speed (<15KMH), maximum gradient suppoted <15%. No effect at high speed.|

15%

Notice: It is recommended for high-intensity riders to ride in plug-in mode for electricity to dissipate heat for T2 after stop.

Indicators

Application

  1. Please download “CYCPLUS” App in App Store or Google Play.
  2. T2 is a true direct-drive trainer and requires no calibration.
  3. T2 supports both Bluetooth and ANT+ wireless connection protocols when using indoor cycling Apps.
    We recommend using a Bluetooth connection in preference, for more stable signal.
    For ANT+ connection, place the ANT receiver as close as possible to the indicator spot on of T2.

Spacers

(for possible noise and friction)
Cassette adjustment spacer(for loud chain noise)

If the chain noise becomes too loud while training, it may be because the distance between the T2 cassette and the rear fork (A) and the distance between your original cassette and the rear fork (B) are different, and the bike chain and cassette do not fit well.

  1. A<B Try adding more cassette adjustment spacers to T2. Each piece is about 0.5mm thick.
  2. A>B Contact us directly for more help.

Disc brake spacer(for friction)
If friction occurs between the disc brake on your bike and the T2 housing, you can use disc brake spacers to increase the distance between to avoid friction while training.
*This mostly happens with SRAM spec 140mm disc brakes.

Visit our youtube channel (CYCPLUS) for more detailed official videos, or contact our customer service for more information.

Specifcations

Model CYCPLUS T2
Type Intelligent Direct – Drive Trainer
Magnet 50 neodymium magnets + 45 sets of electromagnets
Structure Foldable X-shape
Dimension(unfolded) 520699510 mm
Dimension(folded) 300257510 mm
Net Weight(with cassette) 33.5lbs(15.2kg)
Power supply 48V/1.25A(Unplugged mode suppoted)
Max power 2200 W
Output power(40km/h) 1600 W
Accuracy ±1%
Calibration No calibration needed
Max gradient 15%
Downhill simulation Plug-in mode only
Max torque 60 N.m
Max braking force 176 N
Wireless signal Bluetooth 5.0 & ANT+
ANT+FE-C protocol
FTMS protocol
Frame compatible 5130/5135(Quick release) 12142/12148(Thru-axle)

Cassete compatible

| Shimano 8-12 speed cassette SRAM 8-11 speed cassette

SRAM 12 speed cassette(XDR hub needed)

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • (1) This device may not cause harmful interference, and
  • (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals