SAIC GM WULING TMSS6A4 S6.6 Tire Pressure Sensor User Manual
- June 10, 2024
- SAIC GM WULING
Table of Contents
SAIC GM WULING TMSS6A4 S6.6 Tire Pressure Sensor
The S6.6 Tire Pressure Sensor is a TPMS (Tire Pressure Monitoring System) solution that can monitor the tire pressure and temperature in real-time. It gives an alarm for abnormal tire pressure and temperature and reminds users to maintain reasonable tire pressure. The system consists of a sensor that is installed in the car tire to detect the pressure and temperature of the car tire, a controller that is installed in the car body to receive the transmitted signal, and an RF receiver module. The tire data information is transmitted to the instrument for display through the CAN bus.
Product Structure
The overall appearance of the S6.6 structure is relatively wider and thinner. The edge of the S6.6 structure shell is rounded, and the rib design is optimized to ensure the overall strength of the shell. The battery is parallel to the PCB, and the valve is included in the structure. The overall size of the sensor is 75.547.313.1, and the overall weight is about 20.1g.
Performance Parameters
The S6.6 Tire Pressure Sensor has a pressure range of 0~800 kPa, working temperature range of -40~+125 ℃, working voltage of 3V, RF frequency range of 433.05 – 434.79 MHz, RF baud rate of 9600 bps, frequency deviation of -1.78 kHz, and power of 1.0~9.0 dBm.
Installation
It is important to follow the product installation instruction manual for detailed installation process. Some cautions to be kept in mind are:
- Do not install the sensor on an unapproved rim.
- Do not repeatedly install or disassemble the sensor.
- Ensure that the rim is properly installed with sensors in good condition.
- Do not damage the sensor during the installation and disassembly process.
FCC ID : 2AVYX-TMSS6A4
FCC statement
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Product name : SENSOR ASM-TIRE PRESS IND Type:TPMS-00-01
TPMS system solution
Tire pressure monitoring system: It can monitor the tire pressure and
temperature in real time, give an alarm for abnormal tire pressure and
temperature, and remind users to keep Maintain reasonable tire pressure
(including sensor, controller)
The sensor is installed in the car tire to detect the pressure and temperature
of the car tire; the controller is installed in the car body to receive the
transmitted signal. The sensor signal, and the tire data information is
transmitted to the instrument for display through the CAN bus.
TPMS sensor
Product structure
3D structure display
Sensor structure design
Performance parameters
Fundamentals of chip work
Sensor installation
Instructions for installing the sensor
- Hold the sensor, pass the valve through the rim hole, and pre-tighten the nut; (Picture 1)
- Repeat step 1, pre-tighten 5pcs-6pcs rim (one layer of the pallet);
- Hold the wrench with the left hand to clamp Hold the valve chassis or deflect it slightly to the right and stabilize it, and tighten the nut with an electric or manual torque wrench in your right hand. (Picture 2) Installation inspection: After installation, the sensor is in a positive parallel state with the arc of the rim, and the surface of the cover plate is not in contact with the arc of the rim. Then the installation is complete.
Remarks: For the detailed installation process, see the product installation instruction manual
Cautions:
- It is not allowed to install the sensor on the unapproved rim;
- Do not repeatedly install or disassemble the sensor;
- Make sure that the rim is properly installed with sensors in good condition;
- It is forbidden to damage the sensor during the whole installation and disassembly process;
FCC ID : 2AVYX-TMSS6A4
FCC statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Any changes or modificatio ns not expressly approved by the
grantee of this device could void the user’s authori ty to operate the
equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter.