Redmogo AM003 Rechargeable Remote Transmitter and Collar Receiver User Manual

Redmogo AM003 Rechargeable Remote Transmitter and Collar Receiver

Product Information

The dog training system is a device that helps in training dogs with electronic pulse stimulation. It consists of a Remote Transmitter and a Collar Receiver. The collar has contact points that deliver the electronic pulse stimulation. The electronic pulse stimulation is delivered when any of the stimulations are pressed on the Remote Transmitter, and the indicating light flashes green. The collar receiver has an ON/OFF button that powers on/off the Collar Receiver and is used for Pairing or Synchronization of the Collar Receiver to the Remote Transmitter.

Features

• The device has a range of 3000 feet.
• The device has 100 levels of static stimulation and vibration.
• The device has a tone mode option that gives an audible warning.
• The device has an LCD display screen.
• The device is rechargeable.

Rechargeable Remote Transmitter and Collar Receiver. Waterproof Collar Receiver. 100 intensity levels of Vibration 100 intensity levels of Static Shock Standard Tone Easy to use, adjustable Intensity LCD Simple, ergonomic design layout. Quick and straightforward pairing process Range of 3000 feet Capable of simultaneous control of three dogs(extra receiver is purchasable) Adjustable strap to accommodate any size of dogAuto-off feature to conserve power when not in use to extend battery life Remotely turn on/off Collar Receiver

Key Definitions

Remote Transmitter

1. Antenna: Sends signals to the collar receiver.
2. Power Button: Powers on/off the Remote Transmitter.
3. Mode Button: Selects the mode of operation.
4. Intensity Buttons: Adjusts the level of stimulation or vibration.
5. Channel Buttons: Selects the channel for synchronization.
6. Indicator Light: Displays charging status and mode of operation.
7. Battery Indicator: Displays battery level.
8. A/B/C Switch: Selects the group of channels for synchronization.
9. Number Display: Displays the current level of stimulation or vibration.
10. LCD Display Screen: Displays the mode of operation, channel, and battery level.

Collar Receiver

1. Contact Points: Covers the electrodes, and through them electronic pulse stimulation is delivered.
2. ON/OFF Button: Powers on/off the Collar Receiver and is used for Pairing or Synchronization of the Collar Receiver to the Remote Transmitter.
3. Charging Port: Charges the battery of the Collar Receiver when connected to a power source.  Indicating Light: Flashes green when any of the stimulations are pressed. Will blink red if the battery power is low to indicatethe Collar Receiver needs recharging.

Product Usage Instructions

Step 1 – Prepare the Remote Transmitter and Receiver Collar

1. Attach the charging connector firmly to the Charging Port on  both the Remote Transmitter and the Collar Receiver.
2. Plug the charger into a standard wall outlet.
3. A solid red light will appear on the Indicator Light, indicating charging.
4. Once charging is complete, the solid red light will turn to a solid green.
5. Note: Before first use, charge the Remote Transmitter and Receiver Collar until completion.

Step 2 – Pairing Collar Receiver to Transmitter

1. Press and hold the ON/OFF button on the Collar Receiver until the green light flashes once, and you hear a sound D once.
2. Press and hold the Mode button on the Remote Transmitter until you hear a sound D once.
3. The Collar Receiver will beep, and the green light will flash twice to indicate successful pairing.

Step 3 – Test the Training System Functions

1. Adjust the level of stimulation or vibration using the Intensity buttons on the Remote Transmitter.
2. Press any of the stimulation buttons on the Remote Transmitter, and the Collar Receiver should vibrate or provide static stimulation.

Step 4 – Assemble and Fit the Collar Receiver

1. Slide the collar strap through the buckle on the Collar Receiver.
2. Adjust the collar strap to fit your dog’s neck snugly but not too tight.
3. Trim any excess strap length if necessary.

Step 5 – Re-thread the Collar

1. Thread the collar strap through the metal loop on the Collar Receiver.
2. Slide the collar strap through the plastic keeper.
3. Adjust the collar strap to fit your dog’s neck snugly but not  too tight.

General Training Tips

• Use positive reinforcement such as treats and praise to reward good behavior.
• Be consistent in your training methods.
• Start with the lowest level of stimulation or vibration and gradually increase it as needed.
• Do not leave the collar on your dog for extended periods of  time.
• Consult a veterinarian or certified trainer if you have any  concerns about using this product on your dog.

Follow these tips on how to get the best out of your iPets Training Collar

1. Make training sessions short and positive(between 10-15 minutes long for each session. This will enable the dog to keep its attention focused on the trainer.

2. Train one dog at a time

3. During the first initial training sessions, keep the dog in a familiar outdoor  environment. Training in new locations may cause the dog to become distracted causing you to reinforce commands with the Collar Receiver more than necessary.

4. Use a long leash fastened to a non-metallic collar to help the dog’s learning Ensure the additional collar and leash does not interfere with the Contact Points on the Collar Receiver. Do not use the remote training collar without a long leash until your dog is fully trained

5. More success will occur by teaching the dog a command first before trying to reinforce the command with the Remote Transmitter

6. For basic obedience training, vibration is more useful

7. Issue one obedience command at a time, this will reduce confusion and allow the dog to remain focused. Do not use the training system for commands that the dog has not learned

8. During training, look for all the positive changes in the dog’s behavior and remember to reinforce them promptly with ample praise and reward

9. Avoid over-correcting your dog. Use as little remote correction as possible during the training process.

10. When the dog has become apparently perplexed, shift the focus of the training by drawing the dog’s attention to a command they have familiarity. Example
    Tell the dog to sit and give abundant praise and encouragement on successful completion of the sit command.

11. Do not use the training system to correct or eliminate forms of aggression or biting behavior. When the dog is showing signs of aggressive behavior, immediately contact a professional dog trainer in your local area

12. Please keep in mind, that you should keep training sessions short and end every session on a high note. Stop training and play with the dog as soon the dog has accomplished a new level of proficiency

Important Safety Information

WARNING: NOT FOR AGGRESSIVE DOGS Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.

CAUTION: Risk of skin damage: Please read and follow the instructions carefully in this guide.Proper fit of the collars is important because a loose collar may cause inconsistent performance. A collar worn for too long or made too tight on the pet’s neck may cause skin damage, ranging from redness to pressure ulcers (commonly knownas bedsores). These collars can cause pressure necrosis if used incorrectly and is often misidentified as burns. Avoid leaving the collar on the dog for more than 12hours per day When possible reposition the collar on the pet’s neck every 1 to 2hours Check the fit to prevent excessive pressure, and it is okay to trim any excess trap length. Never connect a lead to the electronic collar because it may cause excessive pressure on the contacts. Wash the dog’s neck area and contacts of the collar weekly with a damp cloth. Examine the contact area daily for signs of a rash or a soreIf a rash or  sore is found, discontinue use of the collar until the skin has healed.  If the condition persists beyond 48 hours, see your veterinarian.

These steps will help your pet safe and comfortable. Millions of pets are comfortable while wearing stainless steel contacts. Some pets are sensitive to contact pressure.You may find after some time that your pet is very tolerant of the collar. If so youmay relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are detected,  discontinue use until the skin has fully healed. Thank you for choosing our products! You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our mission is to ensure your pet’s safety by providing you the tools and techniquesto successfully train your pet. Should you have any queries, please contact our customer service.

Note: Please charge before using the product.

How does the dog training system work?
Our products are reliable, effective, and comfortable for large or small dogs. The system assists in controlling your dog without a leash in a range up to 3000 feet away! Instantly send a signal from the Remote Transmitter, which activates your dog’s Collar Receiver. The dog will receive an annoying but safe, harmless stimulation. With correct, consistent use of this product, the dog will associate his misbehavior with your corrections, and soon enough, you will have a well-trained dog. This particular model features adjustable levels of stimulation ,enabling the user to tweak accordingly to the dog’s temperament, removing the risk of over stimulation

Collar Receiver

1. Contact points: Covers the electrodes, and through them electronic pulse stimulation is delivered
2. ON/OFF Button: Powers on/off the Collar Receiver and used for Pairing or Synchronization of the Collar Receiver to the Remote Transmitter. Press the button, the green light flashes once, and the sounds D once, is ON, press again, the green light flashes twice, and the sounds D-D twice is off
3. Charging Port: Charges the battery of the Collar Receiver when connected to a power source. When charging, the red light on and the battery indicator will be displayed. When it is fully charged, the red light off and the green light on, and the battery indicator will be full.
4. Indicating Light: Flashes green when any of the stimulations are pressed Will blink red if the battery power is low to indicate the Collar Receiver needs recharging

Operating Guide

Prepare the Remote Transmitter and Receiver Collar: Charge the Remote Transmitter and Receiver Collar

1. Attach the charging connector firmly to the Charging Port.
2. Plug the charger into a standard wall outlet
3. A solid red light will appear on the Indicator Light, indicating charging
4. Once charging is complete, the solid red light will turn to a solid green is occurring.

Note: Before first use, charge the Remote Transmitter and Receiver Collar until completion.

Powering on and off the Remote Transmitter
There is no need to turn off the transmitter. When there is no buttons being pressed on transmitter, the unit turns off automatically. Press any button and the transmitter will power back on automatically

Powering on and off the Collar Receiver: Press the ON/OFF button on the receiver to power the unit on or off. When  the receiver is powered on, the indicating light will flash green

Pairing Collar Receiver to Transmitter
Note: Transmitter and receiver are pre-paired when leaving our manufacturing facility. In case the pairing is not established or you would like to repair the units, please follow the instructions below

1. Turn on the transmitter first, press the “CH “button to select dog A
2. Power on the Collar Receiver by pressing the ON/OFF button on the Collar Receiver.
3. Press and hold the ON/OFF button for about 3 seconds, the indicator light will start to flash quickly, when the indicator light flashes quickly, please press any button of the transmitter sound, vibration, static key, When the Remote Transmitter and Collar Receiver are paired successfully, the Collar Receiver D beeps, the indicating light will stop flashing.
4. If needing to pair a second Collar Receiver, follow the same steps ,but turn on the transmitter and select Dog B.
5. If needing to pair a second Collar Receiver, follow the same steps ,but turn on the transmitter and select dog C, the A and B icons on the display will light at the same time to represent dog C

Test the Training System Functions
The testing methods will help determine whether the training system is functioning as intended and will also teach you how to operate the system Please ensure that the pairing process is complete before attempting to test the functionality.

Testing the Electronic Pulse Stimulation

Electronic Pulse Stimulation Tester
In your package that you received, you will find a clear almost translucent plastic piece that has a light bulb/fuse in the middle of it. This is your Electronic Pulse Stimulation tester. This component DOES NOT attach to the Collar Receiver by any means and is only for testing the static shock mode. To test the Electronic Pulse Stimulation, follow these steps

1. Put the test light over the Electrodes of the Collar Receiver you wish to test
2. Ensure the Toggle Switch is in the correct position for the Collar Receiver you’re testing
3. Adjust the Intensity Dial off of 100.
4. Press the Static Shock Button on your Remote Transmitter
5. If done correctly, the test bulb should flash red indicating the electronic pulse stimulation is operating correctly

Note: If wanting to test the shock function on yourself, please ensure your finger or hand is across both contact points to ensure the connection is complete. Otherwise, user will

Testing the Vibration Functions

1. Ensure the Toggle Switch is in the correct position for the Collar Receiver
2. Adjust the Intensity Dial off of 100
3. Press the Vibration Button on your Remote Transmitter
4. If done correctly, the Collar Receiver will vibrate

Testing the Sound Functions

you’re testing. Press the Sound Button on your Remote Transfer

1. Ensure the Toggle Switch is in the correction for the Collar Receive
2. If done correctly, the Collar Receiver will emit sound

Assemble and Fit the Collar Receiver

Attaching the Contact Points
In your package that you received, you will find 1 set of contact points
These contact points are screwed onto the receiver so that the points can effectively contact the dogs skin without hair/fur interfering with the connection

Attaching the Collar Strap to the Collar Receiver
The Collar Receiver attaches to the Collar Strap by sliding through the tabs on each side and going wrapping around the back of the Collar Receiver. To accomplish this correctly, please view the diagram below

**Fitting the Collar Receiver

**

Important: The proper fit and placement of the Collar Receiver is essential for effective training. The electrodes must have direct contact with the dog’s skin

1. To fit the Collar Receiver, attach the Collar Strap to the Receiver
2. With the dog standing in front of you, place the Collar Receiver around the dogs neck, so the receiver box and Contact Points are on the underside of your dog’s neck, making direct contact with the dog’s skin If direct contact is not possible, shaving some fur away, to ensure good contact  IS recommended
3. Fasten the collar strap. The fit should be snug, but not taut. A finger should be able to be placed beneath the collar strap when around the dog’s neck
4. Allow the dog to wear the Collar Receiver for several minutes and check the strap again. The dog will soon become more familiar with the Collar Receiver, so it is crucial to ensure the fit comfortable and flattering

CAUTION: RISK OF SKIN DAMAGEFor comfort, safety and effectiveness of this product please check the fit of the dog’s collar frequently. If observing any skin irritation immediately discontinue use of the collar for a few days. If the skin condition persists beyond 48 hours, consult a veterinarian. These collars can cause pressure necrosis, commonly known as bed sores if used incorrectly and is often misidentified as burns

• Do not attach a leash to the collar, which can result in squeezing the Contact Points too tightly against your dog’s neck
• The design of the Collar Receiver discourages constantly wearing the device. recommends the collar not be worn for more than 12 hours out of every 24-hour period

Most dogs feel uncomfortable when wearing the collar for the very first time. Do not use any functions until the dog is accustomed to the collar we suggests giving the dog, the vibration stimulation before following it with a static shock. After training for a while using this method, the dog will be aware that after vibration comes a static shock. Vibration will act as a warning, and static shock only acts a menace that might be necessary sometimes

• Re-thread the collar
• Regular Maintenance
• Ensure Contact Points are not too tight on a weekly basis
• Rinse the Contact Points with alcohol on a weekly basis
• Check the dog’s neck for irritation and wash the dog’s neck on a weekly basis
• Feel free to cut any additional Collar Strap material if it’s too long for your dog

Frequently Asked Questions

Please refer to the product manual for a list of frequently asked questions and their answers.

• How old does the dog have to be before using the system?
  Your dog should have learned basic obedience commands such as, “sit” or” stay.
  The Collar Receiver might be too large for dogs under 15 lbs.

• Once my dog completes training and is been obeying my commands, will he have to wear the collar?
  Probably not. but you may try to reinforce training with the collar

• Can I use the iPets rechargeable training collar with more than one dog?
  Yes, you just need to purchase another Collar Receiver for the system
  Is the Collar Receiver waterproof
  Yes, but always ensure that the Rubber Cover seals the Charging Port

• Can I replace the Collar receiver with another kind of collar?
  No.

• Can I attach a leash to the Collar Receiver?
  No, this can result in pulling the Contact Points too tightly against the dog’s ne
  Attach a leash to a separate, nonmetallic collar or a harness. Ensure the e collar does not put pressure on the Contact Points

• How long can I leave the Collar Receiver on my dog?
  The design of the collar discourages constant wearing. We recommend not having the dog wear the collar for more than 12 hours out of every 24-hour period.

• Is the training system suitable for all dogs?
  The collar is adjustable from length 5.”(15cm)to 19.6″(50cm). if the dog’s neck circumference is smaller than 5.9, you will be forced to rethread the collar. if the dog’s neck circumference is larger than 22″, this collar may not be suitable for the dog. This collar is not suitable for dogs under 15lbs

Troubleshooting

My dog is not responding after successfully setting up the training system

• Charge the Remote Transmitter and Collar Receiver for 6 hours, separately before first use Ensure the Remote Transmitter and Collar Receiver are powered on
• Check the intensity levels of vibration and static shock, making sure it is not set to 0 Ensure the Collar Receiver has sufficient power to operate
• Check the collar to ensure it fits snugly against your dog’s neck
• If tested for all of the above and the dog is still not responding, please try re-pairing the Remote Transmitter and Receiver Collar

The Remote Transmitter does not work

• Check the battery status of the Remote Transmitter.
• If the battery is low, please recharge the Remote Transmitter

My collar-receiver works great for some time, yet it does not work after charging

• First, check if the receiver has been charged correctly. Check the “prepare the collar receiver” part of the guide for the correct charging method.
  Check if the receiver has been powered on

I want to test the Collar Receiver on myself, but it does not work

• When testing the Collar Receiver with your hands, please touch the two electrodes simultaneously, as touching one electrode will not work

Please refer to the product manual for troubleshooting tips.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC ID: 2BAO3-AM003

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>