BOSS MPWT60RGBW 6.5-Inch 2 Way Marine PowerSports Roll Cage Speaker User Manual
- June 10, 2024
- Boss
Table of Contents
BOSS MPWT60RGBW 6.5-Inch 2 Way Marine Powersports Roll Cage Speaker
Product Information
MPWT60RGBW Waketower Speaker Pods
The MPWT60RGBW waketower speakers are high-power, fully-waterproof 2-way systems featuring 6.5-inch drivers and a 1-inch PEI dome tweeter. These speakers are engineered to deliver the highest level of performance and provide years of listening pleasure. With a maximum power handling of 600 watts and a frequency response of 140Hz – 20kHz, these speakers offer clear, crisp sound quality. The built-in crossover network helps to separate the frequencies between the mid-bass driver and the tweeter for improved sound quality. The speakers also feature LED lights that can be controlled using the supplied remote control. The versatile mounting solutions allow for easy attachment to mounting tubes with diameters of 2.25 – 3 inches (57 – 76mm) and are suitable for use in different types of installations. The product comes with all the necessary accessories such as rubber mounting strips, mounting pads, aluminum bands, screws, locknuts, and a remote control.
Product Specifications
- Mid Bass Driver: 6.5 (165 mm) Poly injection cone Rubber surround
- Tweeter: 1 (25 mm) PEI dome tweeter
- Crossover network: Built-in
- Impedance: 4 Ohms
- Power Handling: Max 600 Watts
- Frequency Response: 140Hz – 20kHz
- Sensitivity: 93dB (1 watt/1 meter)
- Dimensions (W x H x D): 7.17 x 11.22 x 7.24 (182 x 285 x 184 mm)
- Gross Weight (excl. gift box): 10.6 lbs (4.8 kg)
Usage Instructions
Before installing the speakers, please read the safety
considerations mentioned in the user manual. It is recommended to
work with an assistant during the installation process.
Step 1: Mounting the Speakers
Attach the speaker pods to the mounting tubes using the supplied rubber mounting strips, mounting pads, aluminum bands, screws, and locknuts. Make sure to tighten the aluminum bands with rubber inserts carefully without over- compressing them. After installation is complete, recheck all bolts and tighten them further if needed before using your boat or vessel.
Step 2: Connecting to Audio Source
Connect the speaker wires to your audio source, ensuring that they are secured in multiple locations along their route to prevent entanglement and injury. The LED lights on the speakers can be controlled using the supplied remote control. Remember that these speakers are heavy products installed in a boating environment where safety should be given utmost importance. Please use extreme caution while installing and ensure that the speakers are not blocking the view of the pilot for safe operation of the vessel or vehicle.
MPWT60RGBW
- 6.5” (165 mm) 2-Way Marine/ Powersports Roll Cage/ Waketower Speaker Pods
Congratulations on your purchase of a product.
- It has been engineered to bring you the highest level of performance. Its quality will afford you years of listening pleasure.
Thank you for making your choice for audio entertainment!
Specifications
- Mid Bass Driver: 6.5” (165 mm ) Poly injection cone Rubber surround
- Tweeter: 1” (25 mm) PEI dome tweeter
- Crossover network: Built-in
- Impedance: 4 Ohms
- Power Handling: Max 600 Watts
- Frequency Response: 140Hz – 20kHz
- Sensitivity: 93dB (1 watt/1 meter)
- Dimensions (W x H x D): 7.17” x 11.22” x 7.24” (182 x 285 x 184 mm)
- Gross Weight (excl. gift box): 10.6 lbs (4.8 kg)
Introduction
- Your new MPWT60RGBW wake tower speakers are high-power, fully-waterproof 2-way systems featuring 6.5” drivers and a 1” PEI dome tweeter. Both speakers have LED lights which can be controlled by the supplied remote control.
- understands that wake tower speakers are used in many different types of installations. Our versatile mounting solutions give you the ability to attach our wake tower speakers to mounting tubes with diameters of 2.25” – 3” (57 – 76mm).
What is included?
Before you begin the installation, please check that your product contains the following contents:
- (2) Speaker pod with male LED connector
- (4) 175x14x1mm rubber mounting strip
- (2) 175x14x2mm rubber mounting strip
- (2) 175x14x4mm rubber mounting strip
- (2) 49x40x2mm rubber mounting pad
- (2) 49x40x4mm rubber mounting pad
- (4) 3″ mounting aluminum band for 3″ and 2.75″ installation.
- (4) 2.5″ mounting aluminum band for 2.5″ and 2.25″ installation.
- (4) M6 locknut
- (4) M6 flat washer
- (4) M6x75mm screw
- (1) LED power wire
- (1) LED connection wire with female connector
- (1) Remote control
- (1) Keychain tag
Safety considerations when installing
Please remember that these are heavy products that will be installed in a boating environment. These vehicles can travel at high speeds and be unstable. So please consider this and use extreme caution. Some safety considerations include:
- Do not mount the speakers in a location where someone may either walk into or strike their head. During a turbulent ride, please make sure that you do not loosen footing and fall or hit the unit, or it may cause injury.
- Secure the wires to the speakers in multiple locations along their route to your audio source, so that there are no hanging loops of wire. Having insecure wires in any hanging conditions can cause entanglement and injury.
- Tighten the aluminum bands with rubber inserts using care. Do not over compress the rubber inserts. After installation is complete, please recheck all bolts and tighten them further if needed before taking your boat or vessel out for an audio adventure.
- Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.
Installation instructions
STEP1
- To adjust the mounting angle, loosen the metal base of the mounting band by unbolting the two screws.
- Make sure to put all components of the mounting hardware in a safe location.
STEP2
- Twist the metal base to determine the optimal mounting angle for the speaker on the cage bar. Then secure the metal base by tightening the two screws.
STEP3
- Place a supplied rubber (49 x 40 mm) pad on the metal base of the mounting band to prevent abrasion and secure clamping.
STEP4
- Place a supplied rubber strip around the cage bar to prevent abrasion and secure clamping.
- Then push two supplied aluminum bands over the cage bar, and align the aluminum bands with the metal base on the speakers.
STEP5
- As illustrated, secure the aluminum bands to the metal base using a pair of M6 x 75mm screws, M6 flat washers, and M6 locknuts. The locknuts must be installed into the hex shaped recess on one end of each aluminum band.
- Hand-tighten the screws to the degree which allows just enough freedom to rotate the speaker around the cage bar.
STEP6
- Speaker installation now completes.
Wiring
Warning
- For safety, disconnect the negative terminal from the source battery prior to wiring.
- Note your amplifier impedance stability prior to wiring.
- Use only high-quality marine-grade speaker wires. Make sure wires are not squeezed or damaged by sharp edges.
-
LED wire connection
Using the supplied LED connection wire with female connector, connect the two speakers through the male LED connectors. -
Speaker wire connection
Using speaker wires (not included) , connect the two speakers to the audio outputs on your 12V amplifier. Make sure to observe polarity. -
LED power connection
Connect one end of the supplied LED power wire to the power input on the speaker, and the other end to the 12V source battery (red color to the positive terminal, black to the negative terminal).
LED light control
The product comes with a remote control for you to control the RGB LED lights
on both speakers.
Keep the remote control safely using the supplied keychain tag.
-
Power on/off
Turn on or off illumination. Make sure the LED power wire is connected to the source battery. -
MODE +/-
Switch from static to dynamic illumination and select a dynamic illumination pattern. -
SPEED +/-
Switch from static to dynamic illumination and select a dynamic illumination speed. -
COLOR +/-
Switch from dynamic to static illumination and select an illumination color. -
BRIGHT +/-
Switch from dynamic to static illumination and change the illumination intensity. -
DEMO
Cycle through red, green and blue illumination.
Battery replacement
The remote control is powered by a CR2025 coin battery. If the battery is depleted, replace it with a new CR2025 coin battery.
- Find the battery compartment at the back of the remote control. Pull the battery tray out.
- Load a new battery with the correct polarity as shown on the tray.
- Replace the battery tray. Make sure the tray is securely inserted.
Important notes on battery
- Danger of explosion if the battery is incorrectly replaced. Replace only with the same type or equivalent type. Observe correct polarity while inserting the battery.
- Do not leave the battery near fire or under direct sunlight. Do not place the remote control in hot places (e.g. on the dashboard). This may cause fire, explosion or excessive heat.
- Remove the battery from the remote control if it is not used for a long time to avoid battery leakage.
- Do not recharge, dismantle or short-circuit the battery or throw it into fire. This may cause a risk of explosion or battery leakage. If spilled fluid comes in contact with your skin or clothing, immediately rinse with water and consult a doctor.
- The remote control contains a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.
BOSS Audio Systems
3451 Lunar Court Oxnard, CA 93030 www.bossaudio.com 805-751-4853 Customer Service Tech Support: www.bossaudio.com/support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>