HALCYON R744 LED Recessed Luminaire Instruction Manual

INSTALLATION R 744

R744 LED Recessed Luminaire

Driver Sold Separately Constant Current – Wire in series
Do not connect luminaire/s to driver if driver is live. Inrush current from live driver will cause instant failure of all connected luminaires. Do not switch secondary side.

Recommended Drivers

Non-Dimmable Driver Options| Description| Number of fittings
---|---|---
DRMACC350 4W| Mini 1-4W| lx R744
DRMACC350 12W| Mini 4-12W| 2-3x R744
DRACC350 20W| Standard 1-20W| 1-5x R744
DRACC350 40W| Standard 14-40W| 5-fix R744
Dimmable Driver Options| Description| Number of fittings
---|---|---
DRDMACC350 4W| Mini 2-4W| lx R744
DRDMACC350 12W| Mini 6-12W| 2-3x R744
DXDUACC350 20W| 10-20W| 4-5x R744
DXDUACC350 28W| 14-28W| 5-8x R744

This luminaire must be installed by a qualified Registered Electrician to prevent damage to the luminaire and maintain electrical safety.

Installation Directions

1. Switch off mains power supply
2. Connect Driver to mains voltage cable (L, N)
3. Carefully install downlight into pre-cut 38mm hole.
4. Turn on mains power and switch on lighting circuit.

Approved Clearances Note: 0mm required but 25mm always recommended for optimum product lifespan through effective heat dissipation.
Example 1: 0mm Approved Height Clearance Building element abutting rear, insulation abutting sides of fitting.
Example 2: 0mm Approved Side Clearance Building element abutting side of fitting, insulation abutting and covering fitting.
All exterior luminaires (with the exception of copper) require periodic cleaning to protect t esuace an or coating rom corrosion and ensure tidy appearance for the lifespan of the product. Wash with care using a soft brush and warm soapy water using a neutral detergent. Coastal areas require extra attention, especially fittings which are under eaves/soffits and do not have any exposure to rain. Do not use a water blaster or high pressure hose. do not submerge fittings for extended periods of time. 316 stainless steel fittings will still develop surface rust or “tea staining’ if left uncared for.
Cutting of holes prior to receiving goods is entirely at the risk of the installer.
10 Basalt Mace. East Tamaki, Auckland. PO Boa 58-501 Botany, Manukau 2161 Auckland, New Zealand Ph(C064 9) 273-9177 Fax (0069 9) 273 9155 Email: sales4Ohalcyon.co.nz web: wena.nalcyonaghta.co.nz

CLASSIFICATION SHEET / IC

exposed to 90°C allowed to abut and cover the luminaire.
---|---|---

In the vicinity of the recessed luminaire, use an insulation product that:
(a) Maintains its dimensions and structural integrity when exposed to a temperature of 90°C; and
(b) Withstands a 30-second needle flame test carried out in accordance with AS/NZS 60695.11.5 with the flame applied to all surfaces of the sample.
Rear of fitting may abut structural members and building elements.
Do not Install through or directly Into joist, beam, rafter or ceiling batten.

Side Clearance from heatsink to building element (e.g. timber, joist or batten)| SCB: 0mm
---|---
Height Clearance from heatsink to building element (e.g. timber, joist or batten)| HCB: 0mm
Minimum insulation clearance to building element| MIC: 0mm

Recessed luminaires and their associated equipment may pose a risk of fire or damage to property if not installed and maintained correctly. Halcyon recommends a clearance of 25mm to building elements for optimum lifespan.
Halcyon IC rated luminaires are completely safe to install in sarked timber ceiling linings.
Halcyon accepts no responsibility if the timber used is not treated correctly and dries out, crack or warps over time due to the constant low heat from the aforementioned “IC Rated” LED recessed lighting.
This data sheet contains information necessary to ensure compliance with the New Zealand Electrical Code of Practice for Installation and Maintenance of Recessed Luminaires and Associated Equipment AS/NZS 60598.2.2:2001

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>