AZZA 850W PC Power Supply 80+ Gold Black User Manual

AZZA 850W PC Power Supply 80+ Gold Black

Product Information: PSAZ-850G Power Supply

Features

• 850W total power output
• Gold efficiency rating
• AC Input: 100-240Vac, 50-60Hz, 10A Max
• DC Output Voltage: +12V, +5V, +3.3V, -12V, +5Vsb
• Detachable connectors for easy installation and cable management
• AZZA ECO Intelligent Thermal Control System for silent operation and improved efficiency

Specifications

• Max Output Current: +12V = 70.8A, +5V = 20A, +3.3V = 20A, -12V = 0.3A, +5Vsb = 2.5A
• Combined Power: 840W
• Connectors: ATX 24 x1, 4+4Pin x2, PCIe 12+4 x1, PCIe 6+2 x4, SATA x9, Molex(PERIPHERAL) x4
• Cable Lengths: ATX/MB 24 Pin – 600mm, CPU/EPS(4+4 Pin) – 700mm, PCIE5.0 16Pin – 600mm, PCI6+2P/PCI6+2P – 700/150mm, PCI6+2P – 700mm, SATA – 550/100/100mm, Molex – 550/100/100/100mm
• Dimensions: 150mm x 86mm x 140mm

Product Usage Instructions

Installation

1. Make sure your PC case is wide enough to accommodate the PSU and RTX40 Series GPU (if applicable).
2. Place the PSU in the appropriate location in your PC case and secure it in place using screws.
3. Connect the ATX 24-pin cable to the motherboard’s ATX power connector and ensure it clicks into place.
4. If your motherboard requires additional power, connect the 4+4Pin cables to the appropriate connectors on the motherboard.
5. If using a PCIe graphics card, connect the appropriate PCIe 12+4 or PCIe 6+2 cables as required by your graphics card.
6. Connect SATA and Molex cables to your storage drives and other peripherals as needed.
7. Use cable ties or other cable management solutions to ensure cables are tidy and out of the way of fans or other components.
8. Ensure that the 12VHPWR cable is not bent too sharply, either vertically or horizontally, and leave around 35mm of cable length for cable management purposes.
9. Replace the side panel of your PC case, ensuring that you do not push it too hard and risk squeezing or damaging cables.
10. Connect the power cord to the PSU and a wall outlet.
11. Turn on your PC and enjoy your new PSU!

AZZA ECO Intelligent Thermal Control System

The AZZA ECO Intelligent Thermal Control System is designed to provide silent operation, improved efficiency, and longer lifespan for the PSU fan. To enable this feature, simply switch the ECO button on the PSU to the “ON” position. This will activate the No Fan Spin feature, which reduces ambient noise and saves on energy costs by only spinning the fan when necessary.

Features

• Complies with ATX12V V3.0
• Efficiency ≧ 90% typical load
• Eco semi-fanless fan control switch
• 120mm Smart Fluid Dynamic Bearing Fan
• LLC Full Bridge Topology with DC-DC module design
• Japanese electrolytic capacitors
• Support PCIe Gen 5.0 graphics card
• High-quality native 16-pin cable supports 600W output
• Complete protection: OCP/OVP/OPP/SCP/OTP/UVP
• 80 PLUS® Gold certified
• Fully modular design

Specifications

Dimensions

Eco Thermal Control System

The AZZA ECO Intelligent Thermal Control System provides silent operation at low loads, improved efficiency and longer life span of the fan. Enabled by a simple switch directly on the power supply, the “No Fan Spin” feature is ideal for users looking to reduce ambient noise overall. Save on energy costs and unnecessary fan usage with the AZZA ECO Thermal Control System.

Detachable Connectors

Connectors

• ATX 24 x1
• 4+4Pin x2
• PCIe 12+4 x1
• PCIe 6+2 x4
• Sata x9
• Molex(PERIPHERAL) x4

Connectivity and Cable Lengths

12VHPWR Cable Guide

Do not bend vertically

Do not bend horizontally

The 12VHPWR connector and the terminals used in it are much smaller than the previous generation. Through our extensive testing, it appears that bending the wires too close to the connector could result in some of the terminals coming loose or misaligning within the connector itself.
This may lead to an uneven load across the other wires, increasing the risk of overheating damage.
The risk of this is substantially higher if the bend is done horizontally in relation to the connector orientation (left to right).

Leave enough 12VHPWR cable length (around 35mm), then do cable management. The connectors should click to lock in.

Bend starting at 35mm from connector

RTX 40 Series is bigger than the rest of the models therefore make sure that the width of the case is wide enough for the PSU and RTX40 Series GPU.
Once complete install the system, please DO NOT PUSH THE SIDE PANEL otherwise the cable will be squeezed and there will be the risk of OVERHEATING & BURNING.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>