PAC GMRVD Overhead LCD Retention Cable Instruction Manual
- June 10, 2024
- PAC
Table of Contents
GMRVD Overhead LCD Retention Cable
Product Information
The GMRVD is a plug-and-play cable that enables the connection of aftermarket monitors and IR headphones to the factory entertainment system in full-size trucks and SUVs with rear seat entertainment (RSE). It can also be used to route audio and video signals to the RSE LCD while keeping the factory head unit. The cable is terminated with RCA jacks for audio and video inputs and outputs.
The GMRVD features a shield wire that should be connected to ground for optimal performance. It is intended for use in conjunction with an OS-4 to retain all safety and convenience systems. The vehicle should be equipped with a Panasonic Overhead LCD and IR system where the DVD player was part of the AM/FM/CD receiver. The OS-4 is needed to power the IR headphone system.
Note that the manufacturer and distributors of the GMRVD will not be held liable for consequential damages sustained in connection with the GMRVD. Additionally, they will not authorize any representative or individual to assume obligation or liability other than its replacement.
Product Usage Instructions
For Keeping Factory Head Unit:
- Connect the GMRVD cable to the audio and video inputs located in the rear of the center console.
- Terminate the RCA jacks behind the radio at this connector.
- Connect the overhead LCD to the A/V output of the new source unit.
- Connect the single black wire (shield) to ground for optimal performance.
- Use an OS-4 to retain all safety and convenience systems and power the IR headphone system.
For Replacing Factory Head Unit:
- Connect the GMRVD cable behind the factory head unit.
- Connect the aftermarket monitor to the audio and video inputs located in the rear of the center console.
- Terminate the RCA jacks on the GMRVD cable for audio and video output.
- Connect the overhead LCD to the A/V output of the new source unit.
- Connect the single black wire (shield) to ground for optimal performance.
- Use an OS-4 to retain all safety and convenience systems and power the IR headphone system.
Overhead LCD retention cable for GMLAN Full Size Truck’s & SUV’s Rear Seat Entertainment (RSE)
(When keeping the factory Head Unit See Reverse Side for Instructions)
The GMRVD is a plug and play cable that routes the audio and video signals to the Rear Seat Entertainment (RSE) LCD. The audio and video inputs located in the rear of the center console are also terminated as RCA jacks behind the radio at this connector.
- When using a head unit with source control (A/V inputs and A/V outputs) – connect the cables labeled “Audio/Video input from Rear Panel” to an A/V input (i.e. A/V 1 in, A/V 2 in). The cables labeled “Audio Video output to Overhead LCD” will then connect to the A/V output of the new source unit. The single black wire is a shield, connect this to ground.
- When using a standalone DVD player (only A/V outputs) – In this case, connect the A/V outputs to the cables labeled “Audio/Video output to Overhead LCD”. The rear panel A/V inputs will not be used and the black shield wire should be connected to ground.
Note: This cable is intended for use in conjunction with an OS-4 to retain all safety and convenience systems. The vehicle should be equipped with a Panasonic Overhead LCD and IR system, in which the DVD player was part of the AM/FM/CD receiver. The OS-4 is needed to power the IR headphone system.
DISCLAIMER: Under no circumstances shall the manufacturer or the
distributors of the GMRVD be held liable for consequential damages sustained
in connection with the GMRVD. The manufacture and it’s distributors will not,
nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the GMRVD other than its replacement.
Pacific Accessory Corporation
- Address: 1502 S. Santa Fe Street, Santa Ana, CA 9270
- Website: techsupport@pac-audio.com
- Voice: 714-835-3022
- Fax: 714-835-3233
Adding Aftermarket Monitors to the Factory Entertainment System
(When Replacing the Factory Head Unit See Reverse Side for Instructions)
The GMRVD is a plug and play cable that allows aftermarket monitors and IR headphones to be connected to the factory entertainment system. The GMRVD is connected behind the factory head unit.
- When using an aftermarket monitor, connect the cables labeled “Audio Video output to Overhead LCD” to the aftermarket Monitor video input. If installing aftermarket IR headphones, connect the RED and WHITE RCAs to the audio input of the aftermarket IR headphones. The cables labeled “Audio Video input From Rear Panel” are not used.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the GMRVD be held liable for consequential damages sustained in connection with the GMRVD. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the GMRVD other than its replacement.
The GMRVD is a plug and play cable that allows aftermarket monitors and IR headphones to be connected to the factory entertainment system. The GMRVD is connected behind the factory head unit.
- When using an aftermarket monitor, connect the cables labeled “Audio Video output to Overhead LCD” to the aftermarket Monitor video input. If installing aftermarket IR headphones, connect the RED and WHITE RCAs to the audio input of the aftermarket IR headphones.
The GMRVD is a plug and play cable that routes the audio and video signals to the Rear Seat Entertainment (RSE) LCD. The audio and video inputs located in the rear of the center console are also terminated as RCA jacks behind the radio at this connector.
- When using a head unit with source control (A/V inputs and A/V outputs) – connect the cables labeled “Audio/Video input from Rear Panel” to an A/V input (i.e. A/V 1 in, A/V 2 in). The cables labeled “Audio Video output to Overhead LCD” will then connect to the A/V output of the new source unit. The single black wire is a shield, connect this to ground.
- When using a standalone DVD player (only A/V outputs) – In this case, connect the A/V outputs to the cables labeled “Audio/Video output to Overhead LCD”. The rear panel A/V inputs will not be used and the black shield wire should be connected to ground.
Note: This cable is intended for use in conjunction with an OS-4 to
retain all safety and convenience systems. The vehicle should be equipped with
a Panasonic Overhead LCD and IR system, in which the DVD player was part of
the AM/FM/CD receiver. The OS-4 is needed to power the IR headphone system
.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the GMRVD be held liable for consequential damages sustained in connection with the GMRVD. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the GMRVD other than its replacement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>