LAZZUR L-C9071-B3-15SN Adour 3-Light 15-Inch Satin Nickel Incandescent Semi-Flush Mount Light Instruction Manual

: June 10, 2024
: LAZZUR

Table of Contents

SAFETY INFORMATION
TOOLS REQUIRED
PRIOR TO BEGINNING INSTALLATION
ASSEMBLY INSTRUCTIONS
How to Identify the Fixture’s Wires
CUSTOMER SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LAZZUR L-C9071-B3-15SN Adour 3-Light 15-Inch Satin Nickel Incandescent Semi-Flush Mount Light

SAFETY INFORMATION

Upon arrival of the product, inspect the wires for any cuts or abrasions that could have occurred while in transit.
IF A DEFECT IN THE WIRE IS FOUND, DO NOT ATTEMPT INSTALLATION.
Please call our customer service team at 786-681-1919 or email us at support@lazzur.com
Proper wiring is essential for safe operation of this fixture. Make sure to not damage the electric wiring of the fixture or any other wiring/lines when drilling.
Check to make sure that no parts are missing prior to beginning installation of the fixture.
Use CSA/UL/ETL listed wire connectors suitable for the gauge, type, and number of conductors.
We recommend installation of this lighting fixture be done by a licensed electrician.
If in doubt about electrical installation, consult a licensed electrician.
All electrical connections must be made in accordance with local and National Electrical Code Standards (NEC) or Canadian Electrical Code Standards (CEC).
Contact your local municipal authority for more information regarding code, inspections, and permits.
L.A.ZZOR lighting fixtures are intended to be installed utilizing compliant NEC/CEC junction boxes.
Before touching any wire, use a voltage tester to make sure it’s not live.
Use non-conductive tools when installing the fixture, such as insulated handles and ladders made of wood or fiberglass.
Turn off power source to the lighting fixture prior to replacing bulbs. Give the bulbs adequate time to cool prior to removing them.

TOOLS REQUIRED

{NOT INCLUDED}

Wire Stripper
Plier
Electrical Tape
Safety Goggles
Ladder
Philips Screwdriver
Flat Blade Screwdriver

PRIOR TO BEGINNING INSTALLATION

Ensure all power supply is disconnected, turn electricity off at the circuit breaker or fuse box and review the instructions before installation. The installation must be handled by a qualified licensed electrician. Also, be sure to turn off power before changing the bulb or cLeaning the fixture.

CIRCUIT BREAKER
WALL SWITCH
FUSE BOX

WARNING

Improper installation may cause electrical shock, fire, or equipment damage. The installer must be familiar with the construction and operation of the product as well as its associated hazards.

ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY
90°C supply conductors minimum. Most houses built before l98S have supply wires rated 60°C. Consult a qualified electrician prior to installation.

Bulbs are NOT included with the lighting fixture. Only use bulbs recommended for your fixture. DO NOT EXCEED THE MAXIMUM WATTAGE.

ASSEMBLY INSTRUCTIONS

Attach the mounting strip (Part #1) to the junction box (NOT INCLUDED) in the ceiling by threading the two provided mounting screws (Part #2) from underneath the mounting strip. The remaining two fixture screws will be threaded through the top of the mounting strip (Part #1), and each will be secured with a hex nut from underneath. The fixture screws will later align with the canopy (Part #5) and be secured with the decorative nuts (Part #4).
Connect the canopy (Part #5) and rod (Part #6) to the fabric shade (Part #7).
Connect the wires by using the wire connectors (Part #3). Make sure to use standard wire connectors when making connections.
- Connect the black wire from the fixture to the black (HOT) wire from the junction box.
- Connect the white wire from the fixture to the white (NEUTRAL) wire from the junction box.
- To connect the grounding wire, there are two options. Each option depends on the electrical wiring in the home and the type of
  junction box being used. You can either:
  l. Partially thread the green grounding screw onto the mounting bar, and then proceed to wrap the grounding wire from the
  fixture around the grounding screw. Tighten the green grounding screw. DO NOT OVERTIGHTEN. If necessary, wrap the
  remaining ground wire from the fixture with the grounding wire from the supply with a wire connector.
  2. Connect the grounding wire from the supply to the fixture ground wire using a wire connector.
- Make sure to wrap each connection with electrical tape for a more secure connection.
- Please avoid having electrical wire exposed when wiring connections.
Align the holes of the canopy (Part #5) with the bottom fixture screws on the mounting strip (Part #1). Lock tightly by using the decorative nuts (Part #4).
Insert the center rod (Part #8) to the base of the lighting fixture.
Insert the lightbulb (Part #9; NOT INCLUDED)
Run the glass shade (Part #10) through the center rod and tighten using the screw (Part #11).