Gaggenau BX 480 Double Oven Instruction Manual

June 10, 2024
Gaggenau

Gaggenau BX 480 Double Oven

Gaggenau-BX-480-Double-Oven-product

Important notes

A Risk of injury!

  • The appliance is heavy. To move the appliance, 2 people are required. Use only suitable tools and equipment.
  • Read these instructions carefully and keep them in a safe place.
  • Safety during use can only be ensured if the appliance is fitted correctly according to these installation instructions. The installer is responsible for ensuring that the appliance operates perfectly at the point of installation.
  • Only allow a licenced professional to connect the appliance.
  • The appliance must be disconnected from the power supply during all installation work.
  • Wear protective gloves to prevent injury from cuts. Parts that are accessible during installation may have sharp edges.
  • Check the appliance for any transport damage before installation.
  • Do not lift the appliance by the door, door handle or lower air vent.
  • For installation, currently applicable building regulations and the regulations of the local electricity supplier must be observed.
  • This appliance corresponds to appliance class 3 for installation in a kitchen unit according to the installation drawing. Observe the minimum distances.

Planning notes

  • Door hinge not reversible.
  • The door panel surface of the appliance extends 47 mm from the furniture cavity.
  • The outer edge of the door handle extends 94 mm from the furniture cavity.
  • Consider the overhang when planning to open drawers next to the appliance.
  • When planning a corner solution, pay attention to the 90° door opening angle.

Preparing kitchen units

  • Important: Pay attention to the weight of the double oven (approx.150 kg with accessories). Transport the appliance in an upright position.
  • Fitted units must be heat-resistant up to 90 °C, and adjacent cabinet fronts up to 70 C.
  • There must be a ventilation cut-out of min. 20 x 500 mm made in the intermediate floor of the surround unit.
  • The appliance connection box must be positioned outside the installation space.
  • Carry out all cut-out work on the furniture unit and worktop before fitting the appliances. Remove any shavings or the correct operation of electrical components may be impaired.
  • Secure freestanding units to the wall using standard, commercially available brackets.
  • Only fit the appliance up to a height that allows accessories to be easily removed.

Electrical connection

  • Make sure that the household installation has sufficient fuse or circuit breaker protection. Check that the appliance has the same voltage and frequency as the electrical installation system (see rating plate).
  • The appliance corresponds to protection class 1 and may only be operated with a protective earth connection.
  • Fuse protection using B or C circuit breakers is required.
  • The installation system must incorporate an all-pole isolating switch with a contact gap of at least 3 mm. This must remain accessible after installation.
  • Appliance without mains connection cable: Only connect as shown on the connection diagram. Fit the enclosed copper bridges as required. Incorrect connection may cause damage to the appliance.
  • Mains connection cable: type HO5 VV-F or higher rated. The yellow/green wire for the PE connection must be 10 mm longer than the other wires on the appliance side.
  • The rear of the appliance has tapered edges. When cabinet depth is 550 mm, the connection lead must be guided down the rear right side of the cabinet to the connector box.

Fitting the appliance

Important: Pay attention to the weight of the double oven (approx. 150 kg with accessories). Transport the appliance in an upright position.

If there is no fitted shelf above the appliance, secure the appliance against tipping over when the door is opened. Fit two standard angles 5 mm above the appliance at 450 mm depth inside the cabinet.

  1. Fully insert the appliance in the cabinet. Do not kink or trap the power cable, or route it over sharp edges.
  2. Centre the appliance. Using a spirit level, adjust the appliance so that it is perfectly level.
  3. Screw the appliance firmly in place with the screws provided. Remove the transportation lock of the door.
Combination with warming drawer

_ Important: _Pay attention to the weight of the double oven (approx. 150 kg with accessories). A stable intermediate shelf must be installed above the warming drawer.

Removal

  1. Disconnect the appliance from the power supply.
  2. Undo the securing screws.
  3. Lift the appliance slightly and pull it out completely.

DIMENSION

Gaggenau-BX-480-Double-Oven-fig-2

Gaggenau-BX-480-Double-Oven-fig-3

INSTALLATION INSTRUCTIONS

Gaggenau-BX-480-Double-Oven-fig-4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals