TURBRO GLH20 Grow Room Humidifier User Manual

TURBRO GLH20 Grow Room Humidifier

SAFETY GUIDE

• Turn off the machine before moving it.
• When the machine is working, do not separate the water tank from the base.
• Do not block the outlet or add water to the mist outlet which may cause water leakage, deformation, or failure and void the warranty.
• This machine requires using pure water below 113°F and use at room temperature between 41 to 104°F.
• The power cord should not be scratched, damaged, knotted, pressed against heavy objects, clamped, or processed. Otherwise, it may cause electric shock, short circuit, or fire.
• Do not connect to a socket that exceeds the rated voltage and don’t use an extension cable to avoid fire or electric shock.
• Do not unplug the power plug with wet hands, otherwise, it may cause electric shock or injury.
• Under thunderstorm weather or no use for a long time, please unplug the power supply.
• Do not use acidic detergent to clean the main body. If the detergent remains, it may produce toxic gas.
• Do not deliberately inhale the spray mist, especially for people with sensitive respiratory tracts.
• Do not put essential oil into the main body/water tank, which may cause water leakage, corrosion, deformation, or damage.
• Do not insert your fingers or other things into the water inlet or air outlet or the gap which may cause damage to the machine or electric shock.
• When not in use for a long time (more than 24 hours), pour out the water in the water tank to prevent mold or impurities from harming your health.
• Do not cover the nozzles while the humidifier is on. Doing so may damage the humidifier.

CAUTION

1. Do not disassemble or modify the machine as this will void the warranty.
2. Keep this machine out of reach of \.Y children. Children should only use this machine under the close supervision of adults.
3. If there is any fault happen, please unplug it immediately and contact the contact us via support@turbro.com.
4. Unplug the power plug when filling and cleaning.
5. Power cord with damage or product \.Y fall or drop, please call the professional guy to repair and detect before using.
6. Please cut the power cord when disposing this product; also any component that may.
7. Be sure the plug is intact before using, in case any accident.
8. Be sure the power supply voltage must be the same as the rated voltage of this product.
9. Do not drop the machine into the \.Y water, do not operate it with wet hand.
10. Keep away from any heat source.

GETTING TO KNOW YOUR HUMIDIFIER

PRODUCT DETAIL

Remote Control

PRODUCT STRUCTURE

• A. Sink
• B. Atomizer
• C. Remote Control Holder
• D. UV Lamp
• E. Power Cord
• F. Air Outlet
• G. Water Filter
• H. Water Tank
• I. Wheels
• J. Nozzle
• K. Cover
• L. Mist Cover

SPECIFICATIONS

Product Name/Humidifier

• Model Number: GLH20
• Voltage: 120V/60Hz
• Power: 105W
• Capacity: 20L
• Mist Output: 700-l000M L/H
• Noise: 35dB
• Timer: 1-12 H
• Safety Function: Waterless Auto Shut-off
• Dimensions: 70.4 x 11.3 x 25.9 Inches
• Weight: 9.5 Lbs

GETTING STARTED

PLACEMENT
Place the humidifier in a horizontal position on a flat surface at least 19 inches away from walls, furniture, furnace, household appliances, etc. Please do not use it on the following occasions to avoid water leakage, signal interference or injury, etc.

1. ODirect sunlight.
2. On an unstable platform.
3. With high temperatures, humidity, and/or dust.
4. ONear an air conditioner, furnace, heater, or stove.
5. Near mobile phones, computers, and other precision instruments. ONear the radio and other objects that emit radio waves.

TWO WAYS TO ADD WATER

Note: We recommend using purified or distilled water to fill the tank to prevent white mineral buildup.

1. Take out the body and add water into the tank. This is the recommended way.
2. Open the cover and add the water directly into the tank.

Attention: Add water slowly and keep an eye on the max fill line to avoid overfilling.

REMOTE CONTROL

The battery includes in the remoter control.

1. Replace the battery: Press O and pull out the battery ring. Put a lithium battery CR2025+ on the top.
2. Operation: Use the remote control within 16.4 feet of the humidifier.

USING YOUR HUMIDIFIER

Touch this button to turn on the machine. The LED display shows the current humidity and temperature (the display switches every minute).

Caution: When the atmosphere lamp lights up, the pump starts to draw water from the tank up to the atomizer. It takes 2.5 minutes to draw up water. During this time, no functions can be operated. After that, the machine will start to work under the default setting. (The machine uses level 2 by default. )

• Touch this button to select the mist spray level from 1 to 3.
• The humidity setting range is between 45-95% in increments of 5% .

Caution: This humidifier will automatically stop spraying mist when the surrounding humidity reaches the set value. If the surrounding humidity is lower than the set value, the machine will resume working.

• The timer can be set for 1-12 hours in increments of 1 hour. The humidifier will turn off automatically when the time reaches the set value.

Caution: The timer function can not be set up when the machine is lacking water.

• Touch the UV button to turn on/off the sterilization feature.

Caution: Do not open the cover if the UV lamp is on.

UV Lamp Sterilization

• UV-C LED Ligh t: (12V DC)
• Wavelength: 240nm
• Rated Power: l.SW

The LED UV-C light is rated at 8000 hours.

1. This function will not produce toxic or harmful by-products, and will not and will not affect the water quality.
2. The UV lamp has high efficiency in removing harmful bacteria.
3. The disinfection effect is influenced by water temperature (Ideal water temperature is 59-77° F).
4. Low power consumption.

Precautions for use

1. This machine contains a UV device. Failure to use the device or damage to the UV lamp cover may cause hazardous UV-C radiation escape. The UV-C radiation can cause damage to the eyes and skin even at very small amounts.
2. It is forbidden to open the tank when using UV exposure, so as not to  harm the eyes and skin of people or animals.
3. The turbidity and suspended solids in water have a large effect on the sterilization effect. To prevent reducing the disinfection effect, please clean the sink and replace clean water regularly.
4. Be sure the UV light cover is intact before using the device.
5. If the UV lamp is damaged, stop using the device. Contact our customer service or a professional to repair it before continuing use.
6. Be careful to prevent damage to the UV lamp when cleaning or using the machine.
7. Press this button for 3 seconds to enter the auto mode. This mode will adjust the mist spray level automatically according to the ambient humidity, and the brightness of the display will reduce by 50%.

Caution: Press any key beside on/off to cancel this setting.

In this mode

Ambient humidity/Mist spray level

• Less than 40%RH: Level 3
• 41-60%RH: Level 2
• 61-70%RH : Level 1
• Over 70% RH: Stop working automatically

Touch this button to turn on/off the atmosphere lamp. Atmosphere lamp settings: cycle, red, yellow, blue, pink, green, white, and off.
Press this button for 3 seconds to turn on/off the water level indicator light.
When the water level is too low, it will make a 5 seconds indication sound. The water shortage icon in the display will light up red and the machine will turn off automatically. All selected functions will turn off together. Please unplug the power plug and refill the water tank.

Caution: When the water in the tank is not enough to be drawn up, the pump will spin, and make noise for around 3-5 seconds. At this time it is best to turn off the unit and refill the water again.

Filter Impurities in Water
The filter ball is a mineral stone, which improves the water quality, increases water activity, and adjusts the pH of water. This water filter is recommended to be replaced every 6 months.

MAINTENANCE AND CLEANING

• Before cleaning, please be sure the machine is powered off and unplugged.
• Clean all the parts with a soft cloth. Never use any hard objects or abrasives to avoid any damage.
• Change the water in the tank and the sink every day to prevent bacterial growth.
• Do not use chemical detergent for cleaning.
• Keep the machine dry and tidy when not in use for a long time.
• The water filter is suggested to be changed after 6 months of use.

ATTENTION

• This machine requires pure water below 113° F only, and uses it at room temperature between 41 to 104° F.
• When the room temperature is lower than 32° F, please pour out the water in the water tank and the sink to avoid freezing and damaging the machine.
• Make sure the water level is not over the Max line in the tank.
• If this unit is not in use for a long time (more than 24 hours), please pour out the water in the water tank and the sink to prevent mold or impurities from harming your health.
• Do not put essential oil into the main body/water tank, which may cause water leakage deformation or damage.
• If accidents happen, such as the machine falling down, or water going inside the unit, please unplug the machine and let it dry, then contact our after-sale service via support@turbro.com or call at 323-438-3334.
• This machine is for indoor use only. This machine is not suggested to use on the wooden floor in case of any damage by moisture.
• The floor in front or surrounding can become slippery. Take extra caution if you have wooden floors or carpets susceptible to mold.

Descaling
After long-term use, there will be a scale deposit on the mechanical sink and vibrating piece. The scale will reduce the atomization effect. Therefore, it is recommended to clean the scale in the sink and the vibration piece every week.

1. Before cleaning, please make sure the machine is powered off and unplugged.
2. Pour a scale-removing liquid (e.g. white vinegar) into the water tank, then add warm water of about 140° F. Let the liquid completely dissolve and soaked for 5-10 minutes.
3. Clean the dirt on the wall of the sink and the vibrating plate with a soft bristle brush or a clean soft cloth.
4. Pour out the water. Be careful to prevent water from entering the base from the air outlet, which may cause the circuit board to short-circuit and damage.

TROUBLESHOOTING

Fault Reasons and Solutions

Issues| Analysis| Troubleshooting method
No power| Power is not connected| Check the power connection

The spray of water has an odor

| The new machine is closed tightly| Open the water tank and leave it for 12 hours before use
The water in the water tank has been inside for too long time|

Replace with clean water

White dust appears around the humidifier| The water contains high mineral content| Use purified or distilled water to fill the humidifier

A small amount of fog

| The atomizing sheet has a scale| Clean the atomizing sheet
If the water is dirty or has been stored for too long time| Replace with clean water
Water temperature is too low| Add a small amount of warm water
The fog amount is set at the minimum gear| Reset the fog amount

Abnormal noise

| Water shortage in the tank, noise from the pump is spinning| Add water to the tank
Placed on uneven ground| Place it on a solid and stable surface

Water leakage

| Too much water| Make sure the water level is below the Max line.
Placed on uneven ground| Place it on a flat and level surface
Remark: If the fault cannot be eliminated after the above, please contact our support team for assist ance .

WARRANTY & CUSTOMER SUPPORT

WARRANTY: TURBRO provides a 1-year limited warranty for TURBRO products from the date of purchase, subject to the following conditians and limitations outlined belo Ow.

What is covered?
This warranty is limited to the repair or replacement of part(s) proved to be defective in material or workmanship, after said defect is confirmed by the manufacturer’s inspection. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).

What is not covered?

• Damage caused by the owner when attempting to fix or alter the product themselves.
• Damage caused by misuse, abuse, neglect, alterations, or unauthorized repair.
• Natural depreciation.
• Any alteration misuse of the product will nullify this warranty.
• This warranty is non-transferable, which is effective for the original buyer from the authorized seller only.

How to request warranty services?
To obtain the benefit of this warranty please leave a message online www.turbro.com/contact ), or send an email to support@turbro.com,
What will TURBRO do?

• Repair the item,
• Replace the item if not repairable.
• Refund the item under certain circumstances.

QR SCAN

www.turbro.com

CUSTOMER SUPPORT

We are here to help anytime!
Any problems, write to us via support@turbro.com. We will get back to
you within 1 business day.

support@turbro.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>