SYNCHRONY T600 Tower Loudspeaker Owner’s Manual

**T600 Tower Loudspeaker
Owner’s Manual

**

Introduction

Congratulations on purchasing a member of the PSB Synchrony Series. Synchrony represents the finest application of PSB’s design philosophy which has been refined over nearly 50 years.
In order to assist in the enjoyment of your speakers, we have provided you with some instructions for assembly, and some suggestions to help you optimize their performance.
Additional information may be found on our website: www.PSBspeakers.com

Port Cover (Figure 1)
Two Port Covers are supplied with each tower. The port cover can be used to adjust the bass tuning of the Synchrony T600 where room problems at low frequencies (in the  1OOHz region) occur. It is well known that the room can dominate the performance of the low frequencies below 200Hz and the added flexibility of a port cover can tweak/improve the performance in problem room setups.
We invite the listener to try plugging any one or multiple ports to better integrate the system in their room because any adjustment of the bass balance could be a welcome improvement in a given system setup. Please experiment; it will be worth the effort in many cases. It is impossible to predict what type of room or what the system setup will be,  therefore we think the flexibility of multiple ports allows the speaker to be integrated better in a wider variety of situations.
Sometimes tweaking like this can be used to really help “dial in” the best possible sound in your room.

Speaker Terminal Jumper Bars (Figure 2 / 3)
The Synchrony T600 also includes two speaker terminal jumper bars. This will provide listeners with tri- and bi-wiring capabilities, as well as tri- and bi-amping. Though the audible differences of these features may be subtle, the benefits include; transients are less likely to cause clipping and/or speaker damage, reduced distortion, and the elimination of errors at low frequencies, while also providing better matching between the power amplifier and speaker.

Installation of IsoAcoustics (Figure 4)
The Synchrony T600 is furnished with GAIA II isolators by IsoAcoustics’, to provide a high degree of speaker isolation, while resisting lateral movement.
Note: The isolators are directional, make sure to install the GAIA’s with the logo facing forward.

1. Carefully lay the speaker down on its side on a soft-padded surface to avoid scratching or damaging the cabinet.
2. Install each of the GAIA isolators through the base of the speaker, leaving no more than 6mm between the isolator and the underside.
3. Carefully stand the speaker upright on the floor.
4. Do not slide the speakers on the floor. Lift the speakers and lower them to the final position, or tilt the speaker and position a cloth or furniture slider underneath the isolators to allow them to slide on the floor. Remove the furniture sliders or cloth once the speakers are in the final position.
5. Once in position, level the speaker by adjusting the height of the GAIA isolators. When making adjustments, tilt the speaker so that the isolators are raised above the floor, then rotate the GAIA isolators to adjust their height.
6. Tilt the speaker and rotate the GAIAs so that each isolator has the IsoAcoustics logo facing forward.
7. Finish by firmly installing the threaded caps on the top of the studs.

Custom isolators (Figure 5)
The Synchrony B600 are equipped with custom isolators from IsoAcoustics which are integrated into the base of each speaker.

Specifications

Frequency Response
On Axis @0 +/- 3db
On axis @0 +/- 1 1/2db
off Axis @ 30 =/- 1 1/2db
LF Cutoff 35Hz| 50-33,000Hz
55-20,000Hz
55-10,000Hz
35Hz| 24-23,000Hz
30-20,000Hz
30-10,000Hz
20Hz
Sensitivity
Listening|      86dB      88dB|   89dB
91dB
Impedance
Minimal| 6 Ohms
4 Ohms| 4 Ohms
4 Ohms
Input Power
Recommended  Program| 15-150 Watts
150 Watts|  20-300 Watts
300 Watts
Acoustic Design
Tweeter| 1” (25mm)  Titanium Dome  with Ferrofluid|  1” (25mm)  Titanium Dome with Ferrofluid
Midrange| | 5 1/4” (133mm) Cast Basket CarbonFibreCone   Rubber
Woofer| 6 1/2” (165mm)  Cast Basket
Carbon Fibre ConeRubber Surround| 3 x 6 1/2” (165mm)
Cast Basket  Carbon Fibre Cone  Rubber Surround
Crossover|  2,200Hz, L4| 450Hz
B3, 1800Hz
Design Type| 2-way system
Bass Reflex, Rear facing port| Transitional 3-way system  Bass Reflex,  Triple Rear facing ports 3 Individual Woofer chambers
Dimensions
Size ( WxHxD)| 9 x 15 1/2 x 11 1/2”
228 x 393 x 298mm| 9 x 41 1/4 x 13 1/2”
228 x 1048 x 343mm
Net Weight| 23 lbs
10.4 kg| 77 lbs
34.9 kg
Finish| Walnut High Gloss| Walnut
High Gloss
Features| Dual, 5-way, Gold-plated Binding Posts, Bi-writeable/Bi-mappable, Magnetic Grille is acoustic isolation Feet Rear Facing Port| Triple, 5-way Gold-plated Binding Posts Tri-were able/Tri-mappable, Magnetic Grille Outrigger stabilizers with is acoustic GAZA II feet Port Plug (x2) Subdivided discrete chambers 3 Individual Woofer Chambers Triple Rear Facing Ports

PSB Speakers
633 Granite Court
Pickering, Ontario. L1W 3K1 CANADA
www.psbspeakers.com 
888-772-0000
905-831-6555
Fax: 905-831-6936

References

• PSB Speakers - Music and Home Theatre Loudspeakers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>