Uniwatch B0BPB5M3WS Smart Home AI Wifi Video Doorbell User Manual

Uniwatch B0BPB5M3WS Smart Home AI Wifi Video Doorbell

Product Appearance

**1** Doorbell comes with a 4500mAh rechargeable Li-ion battery.

Introduction to Chime

**2** Please mind the battery polarities when installing

Charge the Doorbell

Prior to the doorbell installation, please charge up your doorbell for about 8-10 hours till the charging LED turns BLUE from RED.

Compatible charger ( not provided ): USB compatible mobile phone charger (DC 5V 1A~2A)

App download

Search ‘CloudEdge’ in the App stores or scan below QR codes to download the App.

|
---|---
|

Set up doorbell

1. Switch on power for your doorbell, and you will see the LED indicator flashes red (once per second). Start setting up your doorbell following the in-app instructions.
   

2. Tips

• Please operate the setup near your Wi-Fi router.

• Make sure your phone is connecting to a 2.4GHz Wi-Fi.

• Make sure the doorbell is turned on, and its indicator LED is flashing red.
  If not, press and hold RESET for 5 seconds.

• Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.

Pair with your indoor chime

1. Click the SETTING button on the chime, and the chime will be in pairing mode for 20 seconds, with its red LED flashing.
   

2. Pressthe doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds.
   

3. Chime settings.
   Settings.
   Click to enter/quit pairing mode;
   Press & hold for 5 seconds to restore factory defaults.
   Volume control button.
   Click to control volume:
   level 1: 110 dB; level 2: 100 dB
   level 3: 90 dB; level 4: 80 dB
   Ringtone selection.
   Click to change ringtone (4 ringtones available).
   

Install Your doorbell

1. Select location for your doorbell.
   

2. (OPTIONA, not include) Install at an angle.
   You can purchase the following angled brackets so as to point your doorbell to a specific view angle.
   

3. here are two ways to install the doorbell (1)Standard installation.
   
   

(2) 3M installation.

• A. Clean the surface

• B. Remove the liner

• C. Apply pressure to the joint.

• D. Wait 24 hours and let it set

Tips:

• The doorbell cannot be sticked to the rough walls and the surface that is easy to oxidize, such as lime walls/the surface of the iron, otherwise the doorbell will fall off because the viscosity is too low. In this situation, we recommend using screw to install the doorbell so that can ensure the safety, stability and durability of installation.

Tamper Alarm

Anti-theft Tamper Alarm.
You can also enable the anti-theft alarm in doorbell settings

Tamper Alarm On
With tamper alarm on, your doorbell detects disassembly by the trigger on its back, and then a 30-second siren alarm will be triggered. Meantime, video recording get started, and alarm notification will be pushed to the owner’s APP account.
Tamper Alarm Off
You can disable the tamper alarm in doorbell settings, and detach the doorbell without any alarm for battery recharge or regular maintenance.

Trouble Shooting

Q1: Is the video doorbell powered by battery?
A1: Yes, there is a Li-ion battery built-in. Thanks to the low power consumption technology, a full charge lasts for more than 2-3 months in our lab test environment. (Lab test condition: 10 events per day, 15 seconds video recording per event)
Q2: Does it support legacy hardwire power source?
A2: No, it doesn’t. If you need longer battery endurance, suggest that adding a solar battery charger for your doorbell, if only there is sunshine in your doorbell location. You can contact our after-sale service to know where to buy.

Q3: Does it work with existing mechanical chime?
A3: No. The doorbell comes with a battery powered wireless chime to notify people when your visitor presses the doorbell button. If you have an existing indoor chime, please use the provided jumper to bypass the existing chime, so as to provide sufficient power to the new video doorbell. And our wireless chime is 100% wireless, you can place it almost everywhere you like. The transmission distance in open space is more than 100 meters (328 feet).
Q4: How many wireless chimes can be added to the doorbell?
A4: You can add as many wireless chimes as your wish on one video doorbell. EN 13
Q5: Does it support customized Motion Detection Zones?
A5: Yes it does. You can customize the detection zone in the doorbell settings.
Q6: Does the doorbell support cloud storage?
A6: Your doorbell support local video storage by TF card . And you can also activate the cloud storage service in the App. There is a 7-day-free cloud recording trial service.

Thank you for choosing Uniwatch Smart Ai Video Doorbell Powered security camera! If you have any questions about our products and service ,Please do not hesitate to contact us :

FCC Statement

This device complies with part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must acceptany interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

: support@anpvizsecurity.com
: www.anpvizsecurity.com

References

• Anpviz Security | IP Security Camera Manufacturer & Supplier Found In 2014

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>