SUNNY IP66 Series Emergency Exit Sign Light User Manual

SUNNY IP66 Series Emergency Exit Sign Light

Product Information: Emergency Exit Sign Light – IP66 Series

The Emergency Exit Sign Light – IP66 Series is available in both single-sided and double-sided options. It features LED AC indicating input status and full LED charge indicating battery
status. The device has three switches: ON, OFF, and TEST for turning on, turning off, and testing device availability, respectively. The constant voltage battery charging circuit allows for long battery life. The High Temperature type Ni-MH batteries make it suitable for emergency exit signs installed in high-temperature areas.

Features

• Grade 304 stainless steel housing
• Protected against jets of water and dust tight certified by Electrical and Electronics Institute for IP 66 standard
• Lifetime of over 50,000 hours
• ELT Type acrylic sheet that evenly diffuses light throughout the whole sign
• Constant voltage battery charging circuit for long battery life
• High-Temperature type Ni-MH batteries that are suited for emergency exit signs installed in high-temperature areas

Product Usage Instructions

1. Test the power outlet to ensure it is providing 230VAC electricity.

2. Install the emergency lighting unit in the desired area.

3. Open the front cover of the unit by releasing all four locking clips and pressing the ON switch.

4. Plug the unit into a power outlet with 230VAC 50Hz electricity and check the CHARGE or FULL LED light to see the status of the battery.

5. To test the operation of the machine, press the TEST button.
   The light from the sign must be bright continuously.

6. Check for any debris inside the unit and remove if necessary.
   Close the front cover of the unit, lock it with all four locking clips, and lock it firmly to prevent water and dust from entering the unit.

Important Notes

• Do not turn on the device when it is not in use as it will use the battery and affect its performance and lifespan.
• The battery should be immediately charged after each use to prevent a shortened battery life.
• The unit should be stored in temperatures under 25 degrees Celsius and the battery should be charged every 3 months to maintain its operational life.
• Every time the front cover of the machine is opened for any purpose, store the power cable before closing the front cover securely to prevent water and dust from entering the unit.

Initial Troubleshooting

If power is not getting to the unit after plugging in and the LED AC light does not turn on, check the power outlet to make sure it is providing 230VAC electricity. If the outlet is providing electricity, contact customer service for further assistance.

PRODUCT FUNCTION

Product Features

1. The hosing is made from Grade 304 stainless steel protected against jets of water and dust tight certified by Electrical and Electronics Institute for IP 66 standard.
2. Having LED lifetime of over 50,000 hours.
3. The sign is made with ELT Type acrylic sheet that evenly diffuse the light throughout the whole sign, even after an extended period of use.
4. The constant voltage battery charging circuit limits the charging current for long battery life.
5. The High Temperature type Ni-MH (Nikle Metal Hydride) batteries are suited for emergency exit signs that are installed in areas with high temperature such as above ceiling spaces, walkways, fire escapes and other areas.

Installation and Operation

1. Test the power outlet to make sure it is providing 230VAC electricity. If this is not the case, correct the issue before moving for ward to the next step.
2. Install the emergency lighting unit in an area where emergency illumination is desired. Perform inspection checks to make sure the unit is installed properly to prevent accidents such as the unit coming loose and falling.
3. Open the front cover of the unit to turn on the device by releasing all four locking clips and opening the front cover.
4. Press the “ON” switch on the unit. The sign will illuminate.
5. Plug the unit into a power outlet with 230VAC 50Hz electricity and check the “CHARGE” or “FULL” LED light to see the status of the battery. The “CHARGE” LED will be on when the battery is charging and the “FULL” LED will be on when the battery is fully charged.
6. When the unit is in working condition, you can test the operation of the machine by pressing the Test button. The light from the sign must be bright continuously.
7. Check if there is any debris inside the unit. If there is, take it out and close the front cover of the unit, lock it with all four locking clips and lock it firmly to prevent water and dust from entering the unit.

Important Note on Using the Unit

1. When the unit is not in use, do not turn the “ON” switch on the unit as the battery will be used and not charged. It will affect battery performance and lifespan.
2. The battery should be immediately charged after each use to prevent a shorten battery life.
3. The unit should be stored in temperatures under 25 Degree Celsius and the battery should be charged every 3 months to maintain its operational life.
4. Every time the front cover of the machine is opened for any purpose. When finished, the power cable should be stored before closing the front cover and the locking clip must be securely locked on the front cover to prevent water and dust.

Product Initial Trouble Shooting

– Power not getting to the unit after plugging in. The LED AC light does not turn on.| – The power socket might not have any power.

– The unit’s plug has become loose.

– The AC. 230V fuse is blown

| – Check the 230VAC power supply.

– Check the plug and socket.

– Contact customer service.

– The unit and lamp only turns on for a short time after the power went out.

|

– The battery is not fully charged.

– The battery has degraded.

|

– Fully charge the battery.

– Contact customer service to replace the battery

– There is dust or water inside the device.| – Locking clip Is not tight.

– The rubber seal is not completely closed or there is a cable over it.

| – Check the lock clip by locking it firmly.

– Check the rubber seal if there is a cable over it or not, keep the cable inside the unit neatly.

Installation Types

Terms for Warranty and Service

1. The product will only be under warranty if the customer fills in the “warranty card” and return the “return part” to the company within 7 days of purchasing the product. If this is not done within the specified time then the warranty will be considered void.
2. The warranty only covers the unit’s internal parts for the duration specified by the company counting from the date of purchase.
3. Please show the warranty card every time when contacting our service department or the dealer you purchased the unit from.
4. The warranty will be considered void in the following cases.
   • The unit has been used outside of its intended use specified in the manual.
   • The unit has been used with equipment that does not meet the specifications specified within the manual.
   • The unit has been damaged from impact, for example parts are dented, scratched missing or distorted.
   • The unit has been modified or repaired by people not officially certified by our company.
   • The Sticker Warranty Void has been removed or torn.
   • The unit is damaged from negligence or incompetent use, for example, the battery is swollen, the batter has been overcharged, the battery has been damaged from quick charging, the battery
   • has been short-circuited, the battery’s charged has been completely drained.
   • The unit has been stored improperly, for example, it was exposed to moisture causing rust and damage to the internal circuitry.
   • Damaged was caused by a malfunction in the AC power supply.
   • Damage from natural disaster such as fire, moisture, submersion in liquids, chemical damage or from unavoidable circumstances.
   • Damage from animals or insects.
     Note : Please read the manual carefully before installation and operation to understand how to properly operate the unit.

For any further questions about your product
please feel free to contact SUNNY’s customer service department.
Tel. (+66) 02-948-4450-2
E-mail: service@sunnyemergencylight.com

IsOn Import-Export Co., Ltd.
2915-2917 Ladprao Road, Klongjan, Bangkapi, Bangkok 10240

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>