HIKVISION DS-PDC5NC-EG2 Wired Nano PIR Curtain Detector User Manual
- June 4, 2024
- Hikvision
Table of Contents
DS-PDC5NC-EG2 Wired Nano PIR Curtain Detector
User Manual
Wired Nano PIR Curtain Detector
DS-PDC5NC-EG2
User Manual
EN 50131-2-2:2017
EN 50131-1+A1+A2+A3
Environment Class II
Security Grade 2
Certified by TÜV Rheinland
Appearance
-
Front Panel
-
PCBA
a. Terminals
b. PIR Sensor
c. LED Indicator
d. Tamper
e. Direction Jumper
L→R: direction from left to right only
R→L: direction from right to left only
OFF: Turns off the direction selection
f. LED Jumper -
Rear Panel
Installation
Connection Type
Note: The resistor must be connected in series with one end of the
detector.
a. Normally Closed
b. Double End of Line Wiring
Detection Range
Powering On
After powering on, the indicator flashes rapidly. Once the detector self-test
is completed, the LED indicator will go out until the detector detects
movement.
Specification
| Detection Method | Passive Infrared |
|---|---|
| Detection Range | 5 m |
| Detection Angle | 5° |
| Detection Zones | 28 |
| Detectable Speed | 0.3-2 m/s |
| Sensitivity | Auto |
| White Light Filter | 6500Iux |
| Digital Temperature Compensation | Support |
| Creep Zone Protection | Support |
| Digital Processing | Support |
| Tamper Protection | Front |
| Directional Detection | Support |
| Alarm Output | Normally Closed |
| LED Indicator | Blue(Alarm) |
| Transmission Method | Wired |
| Power Consumption | 15 mA Max |
| Power Supply | 9 to 16 VDC |
| Typical Voltage | 12 VDC |
| Operation Temperature | -10 °C to 55 °C (14 °F to 131 °F) |
| Storage Temperature | -20 °C to 60 °C (-4 °F to 140 °F) |
| Operation Humidity | 10% to 90% |
| Dimension(WxHxD) | 29.7 mm x 78.1 mm x 24.8 mm |
| Weight | 32. |
| Mounting Height | 2.4 to 4 m |
| Mounting Method | Ceiling |
| Application Scenario | Indoor |
Please use the power supplies to comply with the requirements of EN 50131-6 at
the appropriate grade and environmental class.
Please do not obscure the detector’s field of view partially or completely.
©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights
reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, dueto firmware updates or other reasons. Please find
the latest version of this Manual at the Hikvision website
(https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals
trained in supporting the Product.
and other Hikvision trademarks and logos are the properties of Hikvision in
various jurisdictions. Other trademarks and logos mentioned are the properties
of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE, AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OFTHE PRODUCT, EVEN IF HIKVISION HASBEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITY FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACKS, HACKER ATTACKS,
VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU
ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE
LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT
DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT
LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, DATA
PROTECTION, AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCTFOR ANY
PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF
MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR
UNSAFE NUCLEAR FUEL CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
** This product and – if applicable – the supplied accessories too are
marked with “CE” and comply therefore with the applicable harmonized European
standards listed under the RE Directive 2014/53/EU, the EMC Directive
2014/30/EU, the RoHSDirective 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with
this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your supplier or
to a designated collection point. For more information
see:www.recyclethis.info
CAUTION**
The socket outlet shall be installed near the equipment and shall be easily
accessible.
The serial port of the equipment is used for debugging only.
FCC Information
Please take attention that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
©2021 Hangzhou Hikvision Digital Technology Co., Ltd.
(https://www.hikvision.com/)
Hikvision
– – “CE” RE 2014/53/EU
EMC 2014/30/EU
RoHS 2011/65/EU 2012/19/EU
(WEEE )- www.recyclethis.info
2006/66/EC ( )- (Cd) (Pb) (Hg)
www.recyclethis.info
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>