BOSCH 0.600.8C0.570 UniversalHedgeCut 50 Hedge Trimmer Instruction Manual

UniversalHedgeCut 50 | 58 | 60
AdvancedHedgeCut 65 | 68 |70

Original instructions

Safety Notes

Explanation of symbols

cleaning, maintaining or if the cable is entangled or if the cable is cut or damaged and before leaving the product unattended for any period.
| Keep hands away from blade.

General Power Tool Safety Warnings

WARNING
Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/ or serious injury. 
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
  Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
  Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving
  parts. Loose clothes, jewelry or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
  Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Hedge trimmer safety warnings

• Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.

• Carry the hedge trimmer by the handle with the blade stopped and take care not to operate any power switch. Proper carrying of the hedge trimmer will decrease the risk of inadvertent starting and resultant personal injury from the blades.

• When transporting or storing the hedge trimmer, always fit the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.

• When clearing jammed material or servicing the unit, make sure all power switches are off and the power cord is disconnected. Unexpected actuation of the hedge trimmer while clearing jammed material or servicing may result in serious personal injury.

• Hold the hedge trimmer by insulated gripping surfaces only, because the blade may contact hidden wiring or its own cord. Blades contacting a “live” wire may make exposed metal parts of the hedge trimmer “live” and could give the operator an electric shock.

• Keep all power cords and cables away from cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.

• Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.

Additional safety warnings

• This tool is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more securely with both hands.
• Always ensure all handles and guards are fitted when using the machine. Never attempt to use an incomplete machine or one fitted with an unauthorized modification.
• Always lubricate the cutting blade with a protective spray before use.
• Always wait until the machine has come to a complete stop before placing it down.
• Other persons and animals should remain at a distance of 3 meters or more when the machine is being used. The operator is responsible for third persons in the working area.
• Never grasp the blade of the hedge trimmer. u Children or persons unfamiliar with these instructions must not operate the hedge trimmer. Local regulations may restrict the age of the operator.
• Never cut a hedge while people, especially children or pets, are nearby.
• The user is responsible for accidents or hazards occurring to other people or their property.
• Do not operate the hedge trimmer when barefoot or wearing open sandals, always wear substantial footwear and long trousers. The use of sturdy gloves, non-skid footwear and safety glasses is recommended. Do not wear loose clothing or jewelry which can be caught in moving parts.
• Thoroughly inspect the area where the hedge trimmer is to be used and remove all wires and other foreign objects.
• Prior to operation, check cutter blades, blade bolts, and cutter assembly for wear or damage. Do not operate with a damaged or excessively worn cutting device.
• Know how to stop the hedge trimmer quickly in an emergency.
• Cut a hedge only in daylight or in good artificial light.
• Never operate the hedge trimmer with defective guards or without the guard in place.
• Always ensure all handles and guards supplied are fitted when using the hedge trimmer. Never attempt to use an incomplete hedge trimmer or one with an unauthorized modification.
• Never hold the hedge trimmer by the guard.
• When operating the hedge trimmer, ensure to keep proper footing and balance at all times.
• Always be aware of your surroundings and stay alert for possible hazards that you may not hear whilst operate the hedge trimmer.
• Keep all nuts, bolts, and screws tight to ensure that the hedge trimmer is always in a safe working condition.
• The hedge trimmer should be stored in a dry, high, or locked up place out of the reach of children.
• Replace worn or damaged parts for safety.
• Do not attempt to repair the machine unless you are qualified to do so.
• Ensure replacement parts fitted are Bosch-approved.
• To safeguard against contact with the moving cutter blade, this hedge trimmer is constructed with two handles each with a blade control (switch). To operate the hedge trimmer, both controls must be actuated simultaneously. Do not use the tool, if it runs without a switch being actuated or just one switch being actuated.

Electrical Safety

Warning: Switch off, remove the plug from mains before adjusting, cleaning, or if cable is cut, damaged, or entangled.

Your machine is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V 50 Hz) Contact your Bosch Service Centre for details. If in doubt contact a qualified electrician or the nearest Bosch Service Centre.
For increased electrical safety use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it. Keep the supply cables away from moving hazardous parts and avoid damage to the cables; this can lead to contact with live parts. The connections (plugs and sockets) should be kept dry and off the ground. The supply cables must be inspected for signs of damage at regular intervals and may only be used if in perfect condition. If the supply cable on the product is damaged, it must only be replaced by a Bosch Service Centre. Only use approved extension cables. Use only extension cords, cables, leads, and cable reels that comply with EN 61242/IEC 61242 or IEC 60884-2-7. If you want to use an extension cable when operating your product, only the following cable dimensions should be used:
– Nominal conductor area of 1.25 mm² or 1.5 mm²
– Maximum length 30 m for a Cord Extension Set or maximum length of 60 m for a Cable Reel with Residual Current Device (RCD).
Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.

WARNING! Inadequate extension cables can be dangerous. Extension cable, plug, and socket must be of watertight construction and intended for outdoor use. Products sold in GB only:

Your product is fitted with a BS 1363/A approved electric plug with an internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

• Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Symbols
The following symbols are important for reading and understanding the original instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the product in a better and safer manner.

Product Description and Specifications

Read all safety warnings and all instructions. Failure to follow the safety warnings and instructions may result in electric shock, fire, and/or serious injury.
Please observe the illustrations at the end of this operating manual.

Intended Use
The machine is intended for cutting and trimming hedges and bushes in domestic use.

Product features (see figures A and B)
The numbering of the product features refers to the illustration of the product on the graphics pages.
(1) Handle (insulated gripping surface)
(2) On/Off switch
(3) Lock-off button for On/Off switch
(4) Hand guard
(5) Blade
(6) Protection sleeve
(7) Mains plug a)
(8) Extension cable
a) country specific

Technical Data

Hedge trimmer| | UniversalHedgeCut 50| UniversalHedgeCut 58| UniversalHedgeCut 60
---|---|---|---|---
Article number| | 3 600 HC0 5..| 3 600 HC0 7..| 3 600 HC0 7..
Rated power input| W| 480| 480| 480
---|---|---|---|---
No-load stroke speed| min-1| 3400| 3400| 3400
Cutting length| mm| 500| 600| 600
Tooth opening| mm| 26| 30| 30
Weight according to EPTA‑Procedure 01:2014| kg| 3.5| 3.7| 3.7
Protection class| | / II| / II| ****/ II
Serial number| | see type plate on garden tool

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

| | UniversalHedgeCut 50| UniversalHedgeCut 58| UniversalHedgeCut 60
---|---|---|---|---

Typically the A-weighted noise levels of the product are:
Noise emission values were determined according to EN 62841-4-2:2019 .

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841-4-2:2019

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841-4-2:2019

That the declared vibration total value(s) and the declared with a standard test method may be used for comparing one tool to another. noise emission value(s) have been measured in accordance

That the declared vibration total value(s) and the declared noise emission value(s) may also be used in a preliminary assessment of exposure. That the vibration and noise emissions during actual use of the power tool can differ from the declared values depending on the ways in which the tool is used especially what kind of workpiece is processed; and the need to identify safety measures to protect the operator that is based on an estimation of the exposure measures in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). Noise emission values were determined according to EN 62841-4-2:2019. Typically the A-weighted noise levels of the product are Sound pressure level of 75 dB(A); sound power level 95 dB(A). Uncertainty K = 2.0 dB. Wear hearing protection! Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841-4-2:2019: ah = 2.5 m/s² , K = 1.5 m/s² .

Operation

• Pay attention to the mains voltage. The voltage of the power source must match the voltage specified on the rating plate of the machine.

Switching ON/OFF (see figures C and D)
To switch ON, firstly press and hold the lock-off button for On/Off switch (3). Then press the On/Off switch (2) and keep it pressed.
To switch OFF, release the lock-off button for On/Off switch (3) and then release the On/Off switch (2).
Sawing Function
Although the tooth opening allows wood to be cut up to Ø 20 mm, the tip of the blade is designed to cut wood up to Ø 25 mm.
Working with the Hedgecutter (see figure E)
Move the hedgecutter evenly forward along the cutting line. The double-edge cutting blade enables cutting in either direction or with a side-to-side motion. Cut the sides of the hedge first, then the top. To cut the sides straight, we recommend cutting from bottom to top in the direction of growth. Younger stems tend to move outwards when cutting them from top to bottom, resulting in shallow patches or holes in the hedge. To reach a level finish, fasten a piece of string along the length of the hedge at the required height and use as an alignment guide. Cut the hedge just above the string. Pay attention that no objects such as wires are cut. The blade or drive can be damaged.

Troubleshooting

Contact Service Agent.
On/Off switch defective| Contact Service Agent.
Motor runs but blades remain stationary| Internal Error| Contact Service Agent.
Cutting blade hot| Cutting blade blunt| Have blade sharpened
Cutting blade has dents| Have blade inspected/overhauled
Too much friction, due to lack of lubricant| Apply lubricant spray
Excessive vibrations/ noise| Machine defective| Contact Service Agent.

Maintenance and Service

Maintenance, Cleaning, and Storage

• Before any work on the product, disconnect the supply cord from the mains.
• For safe and proper working, always keep the product clean.

Do not place other objects on the garden product.
To ensure safe and efficient operation, always keep the product and the ventilation slots clean.
Never spray the product with water.
Never immerse the product in water.
Store the product in a secure, dry place, out of the reach of children.
Do not place other objects on the product.
Keep all nuts, bolts, and screws tight to ensure safe working with the product.
Inspect the product and replace worn or damaged parts for safety.
Ensure replacement parts fitted are Bosch-approved.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information
on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:
www.bosch-pt.com/serviceaddresses

Disposal
The product, accessories, and packaging should be sorted for environmental- friendly recycling.
Do not dispose of products into household waste!

Only for EU countries:
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its implementation into national law, products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

UK Importer:
Robert Bosch Ltd.
Broadwater Park
North Orbital Road
Uxbridge UB9 5HJ

EU Declaration of Conformity| We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.
---|---
Hedge trimmer| Article number
UniversalHedgeCut 50| 3 600 HC0 5..| 2006/42/EC
2014/30/EU
2011/65/EU
2000/14/EC
---|---|---
UniversalHedgeCut 58| 3 600 HC0 7..
UniversalHedgeCut 60| 3 600 HC0 7..
AdvancedHedgeCut 65| 3 600 HC0 8..| EN 62841-1:2015
EN 62841-4-2:2019
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN IEC 63000:2018
---|---|---
AdvancedHedgeCut 68| 3 600 HC0 9..
AdvancedHedgeCut 70| 3 600 HC0 9..

3 600 HC0 5.. /3 600 HC0 7.. : 2000/14/EC: Measured sound power level 90 dB(A), uncertainty K = 1,0 dB, guaranteed sound power level 91 dB(A)
3 600 HC0 8.. /3 600 HC0 9.. : 2000/14/EC: Measured sound power level 92 dB(A), uncertainty K = 1,0 dB, guaranteed sound power level 93 dB(A)
Conformity assessment procedure in accordance with annex V. Product category: 25 Technical file at: *

• Robert Bosch Power Tools GmbH, PT/ECS, 70538 Stuttgart, GERMANY

Henk Becker| Helmut Heinzelmann
Head of Product Certification
---|---
Chairman of Executive
Management

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 20.01.2021

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
F 016 L94 168 (2021.01) O / 217

F 016 L94 168 | (20.01.2021)
Bosch Power Tools

References

• The domain name bosch.mk is for sale
• Početna strana | Bosch u Srbiji
• Skånevik Ølen Kraftlag AS
• Електроінструменти Bosch | Bosch Professional
• Электроинструменты Bosch | Bosch Professional
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Електроинструменти на Bosch | Електроинструменти на Bosch
• Service worldwide
• Elektrické nářadí Bosch | Elektrické nářadí Bosch
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Scule electrice Bosch | Scule electrice Bosch
• Bosch električni alati | Bosch električni alati
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Invented for life | Bosch Global
• Ana Sayfa | Bosch Türkiye
• Početna | Bosch u Hrvatskoj
• herramientasbosch.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>