ZTE E3330 WiFi 6 Wireless Router User Manual

ZTE E3330 WiFi 6 Wireless Router

LED Indicators

–                                  Off

Red                            Steady on

| Options:

• The power supply is not connected.
• The power supply is faulty.

Options:

• ZXHN E3330 is being started.
• ZXHN E3330 is abnormal.

Flashing| Options:
|

• Uplink connection failed.
• Configuration synchronization failed in extender mode.

Green| Steady on The uplink connection is normal.
Flashing The WPS negotiation connection is being implemented.
Blue| Steady on In extender mode, the wireless uplink signal is strong and the configuration is synchronized successfully.
Flashing| In extender mode, the wireless uplink signal is weak.
Green+ Red+ Blue| Flashing| ZXHN E3330 is upgrading software.

Sate Precaution

Usage Cautions

• Read all the safety cautions carefully before using the device.
• Only use the accessories included in the package, such as power supply adapter
• Do not extend the power cord, otherwise the device will not work.
• The power supply voltage must meet the requirements of the device input voltage (The voltage fluctuation range is less than 10%).
• Keep the power plug clean and dry to prevent any risk of electric shock or other dangers.
• Disconnect all the cables during a lightning storm to prevent the device from damage.
• Power off and unplug the power plug when the device is not in use for a long time.
• Do not attempt to open the covers of the device. It is dangerous to do so when the device is powered on.
• Power off and stop using the device under the conditions such as, abnormal sound, smoke, and strange smell. Contact the service provider for mainte- nance if the device is faulty.

The users should read the usage cautions above carefully and will be responsible for any incident resulting from the violation of the above cautions.

Environment Requirements

• Ensure proper ventilation to the device. Place the device away from direct sunlight.
• Keep the device ventilated and dry. Never spill any liquid on the device.
• Do not place any object on the device to prevent any deformation or damage to the device.
• Do not place the device near any source of heat or water.
• Keep the device away from any household appliances with strong magnetic or electric fields, such as microwave oven and refrigerator.

Cleaning Requirements

• Before cleaning, power off the device, and unplug all the cables connected to the device, such as power cable, optical fiber, and Ethernet table.
• Do not use any liquid or spray to clean the device. Use a soft dry cloth.

Environment Protection

• Do not dispose the device or battery improperly. Observe the local regulations about the equipment disposal or treatment. This product is targeted to provide 24 hours continuous triple-play services

Restrictions in the 5 GHz Band
According to Article 10(10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium(BE), Bulgaria(BG), the Czech Republic(CZ), Den- mark(DK), Germany(DE), Estonia(EE), Ireland(IE), Greece(EL), Spain(ES), France(FR), Croatia(HR), ltaly(1T), Cyprus(CY), Latvia(LV), Lithuania(LT), Luxembourg(LU), Hungary(HU), Malta(MT), Netherlands(NL), Austria(AT), Poland(PL), Portugal(PT), Romania(RO), Slovenia(Sl), Slovakia(SK), Finland(FI), Sweden(SE), Turkey(TR), Norway(NO), Switzerland(CH), Iceland(IS), and Liechtenstein(LI). The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

RF Exposure Information
The Maximum Permissible Exposure (MPE) level is calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with the RF exposure requirement, a separation distance of 20 cm between the device and the human should be maintained. Maximum RF output power of the product versions of software/firmware affecting compliance with essential requirement & could be installed/changed by user accessories/components marketed together affecting compliance & could be changed by user.

EU Declaration of Conformity
Hereby, ZTE Corporation declares that the radio equipment type E3330 is in compliance with Directive 2014/53/EU, The full text of the EU decla- ration of conformity is available at the following Internet address: http://support.zte.com.cn/support/cer/EU

Environmental Information
The equipment you purchased has required the extraction and use of natural resources for its production. It may contain substances that are hazardous to people’s health and to the environment. To avoid putting such substances into our environment and to reduce pressure on our natural resources, we ask that you reuse or recycle your end-of-life equipment by using accredited electronics take-back system. The symbols below indicate that this product should be reused or recycled and not simply discarded. Please locate and use an appropriate reuse and recycling site. If you need more information on collection, reuse and recycling systems, contact your local or regional waste administration. You may also contact your equipment provider for more information on the environmental performances of these products.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Product Specifications

Power consumption： 18 W
Environment Requirements| Operation temperature：-5℃ ~ 45℃
Operation humidity：10% ~ 95%

• Manual No: SJ-20220322181146-004
• Edition Time: 2022-05-18(R1.0)

Troubleshooting

The Power indicator on the front panel is off after the power button is pressed.

• Power switch does not turn on.
• The power adapter is not correctly connected to the device. Be sure to use the power adapter supplied with the device.

The green LAN indicator on the front panel is off after the device is powered on.

• The corresponding LAN link is not established.
• The Ethernet cable is not correctly connected to the LAN interface.
• The network device connected to the LAN interface is not powered on.

The WAN indicator on the front panel is off after the device is powered on.

• The WAN link is not established.
• The Ethernet cable is not correctly connected to the WAN interface.
• Please contact the service provider for help.

Unable to connect to the network.

• Check that the Ethernet cable is correctly connected to the WAN interface and the Ethernet cable is correctly connected to the LAN interface.
• Check that the WAN indicator on the front panel is on and the Internet ind- icator on the front panel is solid green or flashing green.

Restore the factory default settings.

• After the power is on, use a needle to press the button for over 5 seconds to restore the default factory settings.

Address: ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China
Postcode: 518057
Tel: +86-755-2677 1900
URL: http://support.zte.com.cn
E-mail: support@zte.com.cn

Install the Device

• If an Internet access device (modem or optical fiber modem) is available, connect the network cable the LAN port of the modem.
•  If no Internet access device is available, connect the network cable to the broadband network port on the wall. :

Sign in

1. Download and install ZLife. For iOS, download ZLife on App Store. For Android, download it on Google Play.

2. Tap Register new account.

3. Enter your email address. Tap By registering, you agree to abide by the ZLife “Software License Agreement” and “User Privacy Policy. Tap Send email.

4. In the registered mailbox, find the ZLife activation email. Tap the activationlink. Log in with the account and password in the email.
   To change your password, go to About> Security> Settings. To cancel an account, go to About> Privacy> Cancel account.

Add the Router

1. Tap Add device.

2. Tap MESH AP

3. Connect the WAN port of the controller to the broadband port. Tap Next.

4. Scan the QR code at the bottom of the controller. If no QR code is present, enter your wireless account and password.
   If the operating system of your mobile phone is Android, you must connect to Wi-Fi manually after scanning the QR code. If you do not want to enter the password manually, tap copy the password. This operation arises from Android rather than ZLife because of Android security requirements.

5. After the controller is added successfully, the Configure network Screen is displayed. Tap immediately. After the controller is added successfully, the indicator is green and steady, and you can manage it remotely. Tap Bind One Mesh network is bound to one account only.

Add the Satellite Routers (If needed)

1. Power on the satellite router.
   The Satellite Routers can be only controller is completely started (the LED indicator of the is installed after the equipment green).

2. After the controller is added, the Add satellite screen is displayed. To add a satellite router, tap Next. During configuration, the indicator of the satellite router is flashing red.

3. Tap MESH AP

4. Tap Next.
   Scan the QR code at the bottom of the satellite router. If no QR code is present, enter your wireless account and password. If the operating system of your mobile phone is Android, you must connect to Wi-Fi manually after scanning the QR code. If you do not want to enter the password manually, tap copy the password. This operation arises from Android rather than ZLife because of Android security requirements.

5. After the satellite router is successfully, the indicator of the satellite added router is blue and steady. Tap Topo at the bottom of the home screen of ZLife to check the connection.
   To add more satellite routers, tap + in the upper right corner of the home screen of ZLife. Tap Add satellite.

NOTES

• Dimension after folding：97*139mm.
• Print color： black printing
• Material：70g writing paper 70g.
• Coating：无.
• Binding process(：Paper folding.
• Output lpi：200 lpi.
• Tolerance:±1mm.
• Raw materials and the corresponding post processing should meet requirements defined in the Environmental Protection Technical Standards

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>