PTN Electronic TPUH660 eARC Extender Over HDBT3.0 User Manual

PTN Electronic TPUH660 eARC Extender Over HDBT3.0

Product Introduction

Thanks for choosing the HDBT3.0 eARC Extender, which consists of a transmitter and a receiver. It can extend 4K or 1080p video to distance up to 328 feet (100 meters) over a single CAT6A cable without compression. It supports eARC. It also supports bidirectional IR pass-through control. 24V PoC feature allows the transmitter and the receiver can be powered from each other and only one power adapter is needed in system.

Features

• 18Gbps high bandwidth, HDMI V2.0.
• HDMI video resolution up to 4K@60Hz 4:4:4, HDR10, Dolby Vision.
• Supports HDCP bypass and HDCP 2.2 compliant.
• HDBaseT 3.0 solution which supports extending signal without compression.
• Extends 4K or 1080p video signals to distances up to 328 feet (100 meters) over a single CAT6A cable.
• Bi-directional IR pass-through control.
• Supports bi-directional 24V Poe.
• Supports eARC (Enhanced Audio Return Channel).
• Provides HDMI loop out on transmitter.

Packing List

• 1 x Transmitter
• 1 x Receiver
• 4x Mounting Ears & 4 Screws
• Bx Plastic cushions
• 1 x Power Adapter (24V DC 1.25A)
• 1 x User Manual
  Note: Please contact your distributor immediately if any damage or defect in the components is found.

Panel Description

Transmitter

1. HDBT OUT: RJ45 port to connect the HDBT input port of receiver by CAT6A Ethernet cable. The LINK LED illuminates when there is a valid HDBaseT link between the transmitter and the receiver. The HDCP LED illuminates when the video contains H DCP content.
2. SPDIF OUT: Connects to audio player (e.g. amplifier) for ARC audio output.
3. DC 24V: DC connector for the power adapter connection.
4. POWER LED: Illuminates green when power is applied, or blinks when in firmware upgrade mode.
5. HDMI IN(eARC): Type-A female HDMI input port to connect an HDMI source device.
6. LOOP OUT: Connects to HDMI display device.
7. IR IN: Connects to the IR receiver for IR pass-through.
8. IR OUT: Connects to the IR emitter for IR pass-through.

Receiver

1. HDBT IN: RJ45 port to connect the HDBT output port of transmitter by CAT6A Ethemet cable. The LINK LED illuminates when there is a valid HDBaseT link between the transmitter and the receiver. The HDCP LED illuminates when the video contains HDCP content.
2. SPDIF IN: Connects to ARC audio source device (e.g.lV).
3. DC 24V: DC connector for the power adapter connection.
4. POWER LED: Illuminates green when power is applied, or blinks when in firmware upgrade mode.
5. FW: Micro-USB port for firmware upgrade
6. HDMI/SPDIF: DIP switch for ARC/eARC mode selection.
   • HDMI: Select the audio source of the HDMI port of the Receiver and send it back to the SPDIF OUT and HDMI IN of the Transmitter
   • SPDIF: Select the audio source of the SPDIF port of the Receiver and send it back to the SPDIF OUT and HDMI IN of the Transmitter.
7. HDMI OUT(eARC): Connects to HDMI display device.
8. IR IN: Connects to the IR receiver for IR pass-through.
9. IR OUT: Connects to the IR emitter for IR pass-through.

System Connection

1. When DIP switch is selected to HDMI, and the TV supports eARC, the TV audio can be transmitted back to the transmitter via HDMI output port of receiver, and then it will be output by the HDMI IN(eARC) port of transmitter.
2. When DIP switch is selected to SPDIF, the ARC audio can be transmitted back to the transmitter via SPDIF IN port of receiver, and then it will be output by the SPDIF OUT & HDMI IN(eARC) port of transmitter.

Note: Please try to f9start the extender if eARC function works abnormally.

Technical Specification

Note: Please use high-qualified HOM/ cable fully compliant with HOM/ V2.0 for reliable transmission and connection.

Distributed by U.T.E: www.PTN-Electronics.de

References

• U.T.E. electronic | Pro AV & IT-Großhandel mit großem Lager PTN Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>