Gaggenau CM470712 Fully Automatic Espresso Machine Instructions

June 9, 2024
Gaggenau

Gaggenau CM470712 Fully Automatic Espresso Machine

IMPORTANT SAFETY PRECAUTIONS

WARNING

When using electrical appliances, basic safety precautions should always be followed, including the following

  • Please read and follow the operating instructions carefully and keep them for later reference.
  • If the unit is transferred, please ensure that this manual is included.
  • Please read and pay particular attention to the safety information in the instruction manual.
  • The fixed water connection should be installed only by a qualified technician.
  • Do not connect the appliance to a hot water connection.
  • Connect the appliance to a cold water connection (fresh water supply). Fresh water supply must be used.
  • The water supply must withstand the operating pressure. The water pressure must be between 0.05 MPa (0.5 bar) and 1 MPa (10 bar). If the water pressure is higher than this, a pressure-reducing valve must be installed upstream. The hygiene regulations must be observed during installation and operation.
  • IMPORTANT: This appliance is designed for domestic and not commercial use.ervise children to ensure that they do not play with the appliance.
  • All units and systems used to deliver the water to the coffee system must conform with requirements of local building and safety codes.
  • The machine must be connected to the water supply in accordance with local and national regulations.

NOTICE: Protect your Coffeemaker and hoses against freezing or it will be damaged.

WARNING

To reduce risk of fire and electric shock: Installation

  • Do not mount any appliance with fixed water connection over the fully automatic coffee machine.
  • Connect and operate the appliance only according to the rating plate specifications.
  • Use appliance only with transformer which is identified as Type 8001010566.
  • Do not connect the appliance to or operate it by means of a time switch or remote control socket.
  • he unit must not be operated with an extension cord.
  • Use the Coffeemaker only if power cord and appliance show no signs of damage.
  • Should a problem occur, pull the plug and disconnect from the power immediately.
  • Never immerse the appliance or power cable in water or any liquid.
  • When connecting or working on the water pipe, disconnect the appliance from the mains power supply. The statutory provisions of the individual country, the local power supplier and the water supply company must be observed. The electrical connection should not be made until after the water connection.

Grounding

This appliance may only be connected to a power supply with 120 Volt AC via a correctly installed receptacle with ground.

Repairs

  • To avoid potential hazards, repairs must only be carried out by authorized service personnel.
  • If the power cord of this appliance is damaged, it must be replaced by a original replacement power cord, which can be purchased from our Customer Service Department.
  • Only an appliance which has been correctly installed according to these installation instructions can be used safely.

To reduce risk of fire and electric shock

  • This appliance is intended for installation in permanently installed cabinetry.
  • Do not install in the same cabinet with other appliances.
  • Do not install in cabinets that are not securely fixed to a support structure. Attach loose furniture to the wall with a conventional bracket.
  • Do not install directly above a cabinet drawer. This appliance must always be enclosed in its own cabinetry unless specified otherwise.
  • Do not place any heating or cooking appliance beneath the appliance.
  • Do not mount the appliance directly over or under or on side of a heating appliance. This appliance must always be enclosed in its own cabinetry unless specified otherwise.
  • Do not mount directly above a sink or connect directly to the sink. Properly follow installation instructions to connect water intake and/or drain (as applicable).
  • Directly mount cabinetry above the appliance. This appliance must always be enclosed in its own cabinetry unless specified otherwise.
  • Do not store anything directly on top of the appliance surface when the appliance is in operation.
  • The appliance can be installed in combination with approved products. Do not install in the same cutout with unapproved combinations.

Note: *Unit may be installed directly above Gaggenau Warming Drawer, Model WS461.

CAUTION To avoid the risk of suffocation: Do not allow children to play with packaging material. Store small parts safely as they can be a choke hazard.CAUTION To avoid the risk of suffocation: Do not allow children to play with packaging material.V Store small parts safely as they can be a choke hazard.

To avoid the risk of injury

Do not reach into the grinding unit. Be careful not to close the door on your fingers. This can result in injury

Unpacking and moving the coffeemaker

The unit is heavy and should be handled accordingly. Proper safety equipment such as gloves and adequate manpower of at least two people must be used in moving the coffeemaker to avoid injury and to avoid damage to the unit or the floor.

Rings, watches, and any other loose items that may damage the unit or otherwise might become entangled with the unit should be removed. Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

WARNING
Hazard due to magnetism
The appliance contains permanent magnets which may affect electronic implants, e.g. heart pacemakers or insulin pumps. Persons wearing electronic implants must maintain a minimum distance of 4“ (10 cm) from the appliance and from the following parts upon removal: milk container, milk system, water tank and brewing unit.

Proposition 65 Warning

This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California: STATE OF CALIFORNIA PROPOSITION 65 WARNING: AWARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Included in delivery

  • (a) Fully automatic coffee machine
  • (b) Installation instructions
  • (c) Assembly bracket
  • (d) Transformer mount
  • (e) Spacers
  • (f) 7 fastening screws (silver)
  • (g) 2 fastening screws (long/black)
  • (h) 1 sleeve (black)
  • (i) 2 fastening screws (short/black)
  • (j) 2 sleeves (white)
  • (k) Transformer
  • (l) Hose guide
  • (m) Hose clamp
  • (n) Fastening screws
  • (o) Hinge dampers

General information for water and drain water connection

The appliance should not be installed more than 393⁄8″ (1000 mm) away from a drain water connection. The water connection can be extended by 1187⁄64″ (3000 mm) with a special pipe (part number 00357081). A shut-off valve must be installed between the water inlet hose and the domestic water connection so that the water supply can be turned off if necessary. The shut-off valve, water inlet and outlet house must be freely accessible following installation. The appliance complies with international standards and may not be connected without a backflow preventer. A tap with a ¾” (26.4 mm) screwed connection is required for connection. If not available, the appliance may be connected only by an approved technician. The water quality must comply with the drinking water regulations of the individual country in which the appliance is operated. The connection to the domestic water supply and all equipment and devices used to supply the water to the appliance must comply with the applicable provisions of the individual country. The drain water connection must be min. 150 mm below the lower edge of the appliance. The drain water hose must not be extended. If the installation location of the appliance is too far away from the main drainage point (siphon), the drainage system (domestic installation) must be adapted.

Prepare built-in units

Important: The power outlet must be located outside the built-in cut-out. Make sure there is adequate aeration. To do this, remove the rear panel or cut out an opening of 1911⁄16″ x 153⁄4″ (500 x 400 mm). There must be a gap of at least 13⁄8″ (35 mm) between the wall and base of the unit or the rear panel of the unit situated above. The ventilation slots and intake openings must not be covered. Also follow the installation instructions for the appliance situated above or below. If installing the appliance above a warming drawer, the height of the recess must be 231⁄4″ (590 mm). If the appliance is installed directly under a décor panel, ensure that there is a ventilation slot of at least 31 square inches (200 cm2). The appliance should not be installed too high, approx. 373⁄8″ (950 mm), to ensure that function parts, e.g. container or brewing unit, can be removed without difficulty. The display should not be located above eye level to ensure legibility. Protect the appliance against freezing or it will be damaged.

CAUTION
Installation must always be performed by two persons.

Installation preparation

  1. Unpack all the parts and check for any damage in transit. Do not operate a damaged appliance. Fig. 1Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-1

  2. Take note of the installation dimensions of the particular model. Fig. 2 Important: Two opening angles can be selected for the door. Depending on the opening angle required, the mounting distance to the wall should be observed before installation.Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-2

    • Opening angle approx. 110° (delivery status)
    • mounting distance to the wall at least 133⁄4″ (350 mm).
    • Opening angle approx. 155°
    • mounting distance to the wall at least 259/16″ (650 mm). For an opening angle of 155°, remove both the restrictors at the top and bottom of the hinge.
  3. Position the assembly bracket (c) according to the measurement stated in the image and fasten it with
    2 fastening screws (f) to the cabinet as shown. The assembly bracket must be positioned at the base of the unit and the wall such that no gap is present. Fig. 3

  4. Fasten the transformer mount (d) with 2 screws (f) in the middle. Fig. 4

  5. Insert the transformer in the mount. The connections to both lines must point to the left. Fig. 5
    Note: When positioning the transformer (k) and pushing in the appliance, do not trap the lines. The transformer (k) is not allowed to touch the appliance and the back wall of the cupboard.

  6. Set the main switch (U) to [Û] on the appliance. Fig. 6
    Note: The appliance can be directly connected to the home network. To do this, insert a LAN cable (not included in scope of supply) into the appliance. Important: Fig. 7Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-
FIG-7

    • The distance between the appliance and the rear wall must be at least 1315⁄16″ (100 mm).
    • The power cord or the LAN cable must not be kinked or crushed.
    • A recess of 423⁄32″ (120 mm) x 1113⁄16″ (300 mm) is required for water inlet hose and drain water hose. If required, adjust the furniture base accordingly.
    • The hose guide (l) should end at the edge of the furniture base.
    • The connecting hose guide (l) should be adapted to the edge of the furniture if necessary.
  7. Screw the hose guide (l) with the fastening screw (i) to the rear wall of the appliance. Fig. 8Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-8

  8. Insert the drain water hose in the hose guide (l).

  9. Place the hose straight on the bottom of the furniture and run down over the edge.

  10. Run the connecting cable, the water inlet hose and the drain water hose through the cabinet to the back. NOTICE: The connecting cable and hoses should not be kinked, crushed or twisted

Drainage connection

The domestic waste water system must be vented. Ensure venting, e.g. through connection to a sink or via a funnel siphon.
Important: The siphon must have a suitable connection. The waste water hose must not be higher than the lower edge of the appliance at any point. The waste water hose should not be kinked, crushed or twisted round. Check that there is no cover in the waste water connection preventing the flow of the water. Remove if necessary.

  1. Position the hose with a continuous slope to avoid a bend. Fig. 10 IGaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-10
  2. Shorten the hose if necessary. Fig. 10 II
  3. Place the hose clamp for the adapter and the adapter on the waste water hose and screw the hose clamp tight. Fig. 11 I-IVGaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-11
  4. Remove the cap from the adapter. Fig. 12 IGaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-12
  5. Place the hose clamp on the adapter. Fig. 12 II
  6. Slide the adapter onto the waste water connection or hang it into a funnel siphon. When connecting to a waste water connection, use the hose clamp to secure the adapter. Fig. 12 III
  7. Check the connections and waste water connection for leaks.
  8. Check the water drainage. To do so, slowly pour approx. 17 fl.oz. (0.5 l) water from a container, e.g. jug, into the drip tray. The water must drain off completely. Fig. 13 If the water fails to drain off, check the installation of the hose and the waste water connection according to the information in these installation instructions.Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-13

Water connection

Open the tap on the water connection and draw off approx. 10 litres of water to clean the domestic water pipe. Then turn off the tap.

WARNING
Risk of electric shock The appliance must be disconnected from the electrical supply.

Only connect the appliance to the cold water connection. Fig. 10Gaggenau-
CM470712-Fully-Automatic-Espresso-Machine-FIG-10
Check that the water inlet hose is not kinked, crushed or twisted. The plastic housing in the AquaStop contains an electric valve so do not immerse in water. The water inlet hose contains the connecting lines so do not cut through this hose.

  1. Screw the water inlet hose with the AquaStop to the tap.
  2. Slowly turn on the tap so it is fully open.
  3. Check the connections and water inlet hose for leaks.

Installing the appliance

  1. Securely insert the front line into the appliance (snaps into place). For this purpose, put the appliance to be plugged in just on to the edge of the unit. Plug the power cord into the socket. Fig. 12 Plug transformer into dedicated receptacle in an accessible cabinet adjacent to the coffee maker (depends on the built-in situation). Do not plug into a receptacle behind the appliance. Push the appliance into the unit until it clicks into place.Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-12
    Important: The socket must be freely accessible after the appliance has been installed.

  2. Check the water drainage. To do so, slowly pour approx. 0.5 l water from a container, e.g. jug, into the drip tray. The water must drain off completely. Fig. 13 If the water fails to drain off, check installation of the hose and the waste water connection according to the information in these installation instructions.Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-13

  3. Check that the appliance is in the middle. If necessary, align the appliance. To do so, pull the appliance out a little, remove the appropriate spacers (e) and attach to the left side (top and bottom). Push the appliance into the unit until it clicks into place. Adjust the appliance so it is aligned horizontally and vertically. The appliance should not stand at an angle of more than 1° (2%) in any direction! Fig. 14Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-14

  4. Take hold of the appliance door on the right next to the outlet and open. Remove the drip tray (Y). Pull the cover (X) on the bottom left-hand side forwards and remove. Pull out the accessories drawer (Z) and put to one side. Fig. 15Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-15

  5. First, screw on the appliance as shown using 2 of each of the fastening screws (f) and (g) as well as 2 sleeves (j). Then screw tight at the top right of the unit using 1 fastening screw (f) and sleeve (h). Fig. 16 Then:Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-16

    • Open the door at an angle of approx. 55°.
    • Screw in the screws (n).
    • Fit the hinge dampers (o).
  6. Only for the qualified installer:
    In very few cases, the door of the built-in fully automatic coffee machine can jam due to a misalignment in the cabinet where the unit is built in. The door can be adjusted. To do this adjust the hinges at the top and the bottom:

    • Adjust the depth of the door by turning the screws (V). Fig. 17.I
    • Remove the hinge dampers at the top and bottom of the hinges. Turn the screws (W) to adjust the inclination and the horizontal position of the doors.
    • Re-fit the hinge dampers. Fig. 17.III
  7. Insert the cover (X) and fix with the two black fastening screws (i). Fig. 18

  8. Replace the drip tray (Y) and accessories drawer (Z) and close the appliance door. Fig. 19Gaggenau-CM470712-Fully-Automatic-Espresso-Machine-FIG-21

Fault in water flow

To ensure an adequate water flow, the filter in the AquaStop should be cleaned regularly.

  1. Turn off the tap.

  2. Unscrew the water inlet hose with the AquaStop from the tap.

  3. Clean the filter with a small brush.
    Important: Do not remove the filter under any circumstances.

  4. Screw the water inlet hose with the AquaStop to the tap.

  5. Slowly turn on the tap so it is fully open.

  6. Check the connections and water inlet hose for leaks.

If the appliance is cleaned and maintained regularly, this will avoid faults

Removing the appliance

  1. Run emptying program. See instruction manual.
  2. Turn off the tap.
  3. Disconnect the mains plug.
  4. Remove the water inlet and water outlet hoses.
  5. Remove all screws. See installation.
  6. Gently pull out appliance.
  7. Pull the appliance out from the cabinet.

Technical specifications

  • Power connection with transformer type 8001010566 (voltage – frequency): 120 V AC – 60 Hz
  • Power rating: 1600 W
  • Maximum static pump pressure: 19 bar
  • Maximum water tank capacity (without filter): 81.15 oz (2.4 l)
  • Maximum capacity of the coffee bean container: 17.64 oz (500 g)
  • Length of power cable (Power socket – transformer): 39″ (1 m)
  • Dimensions (appliance without transformer) H x W x D: 17.91 x 23.23 x 17.48″ (455 x 590 x 444 mm)
  • Weight, empty (appliance without transformer): 46 – 49 lb (21 – 22 kg)
  • Type of grinding unit: Ceramic

AQUA-STOP pledge

In addition to the standard warranty provided by BSH, BSH will also compensate customers for damage caused by a specific fault in the Aqua-Stop system giving rise to a valid warranty claim. Compensation will be provided under the following conditions

  1. If water damage is caused by defect in materials or workmanship in the Aqua-Stop system, BSH will compensate customers reasonable and verifiable damages.
  2. A condition of all warranty claims is the appliance with Aqua-Stop must have been installed and connected correctly in accordance with all instructions; this also includes a properly installed Aqua-Stop extension (genuine accessories). The warranty does not cover defective feed lines or fittings leading to the Aqua-Stop connection at the tap.

BSH Home Appliances Corporation

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals