CADDXFPV SZ07-K012S Micro Digital FPV Vista Kit User Guide

CADDXFPV SZ07-K012S Micro Digital FPV Vista Kit

CADDXFPV Support:
Email: Support@caddxfpv.com

Disclaimer

• Congratulations on purchasing your new CADDXFPV product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use.Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, damage to your CADDXFPV product, or damage to other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of CADDXFP\I’. Visit www.caddxfpv.com for the latest information forth is product.
• By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree to abide by the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and regulations, and all terms, precautions, practices, policies, and guidelines CADDXFPV has made and may make available.
• CADDXFPV accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this document.
  Notwithstanding the above, your statutory rights under applicable national legislation are not affected by this disclaimer.

Introduction

• The CADDXFPVVista is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 120fps image transmission,with a transmission range of up to 4 km and a minimum end-to -end latency within 28ms”.The vista can be mounted on a racing drone and used with OJI FPV Goggles or a remote controller to transmit video,control signals ,and flight controller information wirelessly.

1. lPEX Antenna Ports
2. 3-in-1 Port
3. USB-C Port
4. Linking Status Indicator
5. Link Button
6. Camera

• The end-to-end latency is the total time from camera input to screen display. The device is able to reach its minimum latency and maximum transmission distance (FCC) in a wide open area with no electromagnetic interference.

Connection

Refer to the illustration below to mount and connect the vista to a racing drone.

• RED: Power7.4-26.4V
• BLACK: PowerGND
• YELLOW: UART RX(Connects to Flight Controller OSD lX,0-3.3\IJ
• WHITE: UART lX(Connects to Flight Controller OSD RX,0-3.3\IJ
• BLACK: Signal GND
• YELLOW: DJI HDL(Connectsto Flight Controller S.Bus,0-3.3\IJ
• An electric soldering iron and soldering tin are required for connection. Make sure that there are no short circuits or open circuits when soldering the cables.
• There are up to eight channels for the Vista depending on the region (FCC: eight, CE/SRRC: four, MIC: three).
• Each channel has a bandwidth of 20 MHz. The public channel is 8, which is the default channel when the equipment is powered on. The channel can be changed manually to avoid interference from other devices.
• The Vista may become hot during or after operation.
• DO NOT touch the Vista before it cools down.
• DO NOT use the Vista for an extended period when the temperature is high or there is poor ventilation.
• Otherwise, the Vista may overheat and enter low- power mode which will affect its performance. If the
• Vista enters low-power mode, restart it or wait for it to cool down and it will automatically return to normal.
• Keep the Vista away from metal objects or carbon fiber frames.Make sure to choose a position where the transmission will not be blocked during flight.

Activation

• When powered on, connected the vista to your computer and run DJI ASSIST ANTTM2 for activation.During the activation and upgrade process,there is a lot of heat.Please avoid direct contact to prevent burns.Overheating may lead to upgrade failure and unable to boot normally.You need to aware of the ambient temperature and use a fan to assist cooling.The warranty service does not support the crash caused by firmware refresh.
• Download DJI Assistant2 at https://www.dji.com/fpv/downloads

Linking

The vista support there linking methods:A. B, and A+B (Must link A before B).

1. Power on the vista and the DJI FPVGoggles.

2. Press the link button on the vista and the goggles.”

3. The linking status indicator of the vista turns solid green. The goggles stop beeping when successfully linked and the video display is normal.

4. Power on the vista and the □JI FPV Remote Controller.

5. Press the link button on the vista, and then press the record button, C button, and right dial on the remote controller simultaneously.”

6. Both the linking status indicators turn solid green when successfully linked.

   • When ready to link, the devices will give the following indication: Vista: the linking status indicator turns solid red.
   • Goggles: the goggles beep continually.
   • Remote controller: the remote controller beeps continually and the status indicator blinks blue.

050 display settings

1. After connecting the UART cable to the flight controller take the Beta flight flight controller software setting as an example. Open the corresponding UART port and click save.

2. Select telemetered and OSD.click save.

3. Select the display content you need in the OSD page {some OSD are not supported,please wait for subsequent updates)

4. Select Settings-Display-Custom OSD ON in DJI FPV Goggle

Operating channel

 |  |  |  |  |  |  |
---|---|---|---|---|---|---|---
FCC 5660| 5695| 5735| 5770| 5805| 5878| 5914| 5839
CE/SRRC S735| 5770| 5805| –| –| ·|  | 5839
MIC S660| 5700| –| –| –| ·|  | 5745

Make sure you fully understand and abide by local laws and regulations before using this product.An amateur radio license may be needed in FCC regions when using channels 1,2,6,or 7, as they are amateur frequency bands.Users who use the amateur frequency bands with a modified or cracked version or without a license may be punished for breaking local laws or regulations.

Specifications

• Weight:
  • Vista: 18.5 g
  • Antenna: 2.5g/1.5g
• Dimensions
  • Vista: 30X29Xl3.5 mm
  • Coaxial Cable: 120 mm
• Operating Frequency: 5.725-5 .85 0 GHz
• Transmitter Power (EIRP)
  • FCC/SRRC: <30 dBm;
  • CE; <l4dBm
• Min. Latency{end-to-end)
  • Low Latency Mode (720p 120fps): <28ms;
  • High Quality Mode (720p 60fps): <40ms
• Max. Transmission Distance: FCC/SRRC: 4 km; CE: 0.7 km;
• 1/0lnterface: USB-C,IPEX,3-in- l port
• Supported Flight Control System Operating: Beta Flight
• Temperature Range: 0° to 40° C ( 32° to 104° F)
• Input Power: 7.4-26.4 V

Camera parameters

• Model: Polar cam
• Weight: 9g
• Dimensions: 1 9Xl9X24mm
• Image ratio: 1 6: 9
• Min .Latency: 720p 60fps < 32ms
• Sensor
  • 1/1.8″ CMOS
  • Aperture: F/1. 6
  • Shutter: Rolling shutter
  • lso: 100-25600
  • Min . Illumination: 0.00003Lux
• FOV:!62°(D); l38′(H);75°M
• Model: Nebula pro
• Weight: 6g
• Dimensions: 19X 19X 20 mm
• Image ratio: 16:9/4:3
• Min.Latency:
  • 720p 120fps < 28ms
  • 720p 60fps < 32m
• Sensor:
  • 1/3.2″ CMO0S
  • Shutter: Rolling shutter
  • Iso: 100-25600
• FOV: 150° (D);122° (H);93° (V)
• Model: DJI cam
• Weight: 8.2g
• Dimensions: 21.1×20.1 x27.4 mm
• Image ratio: 16:9/4:3
• Min.Latency:
  • 720p 120fps < 28ms
  • T20p 60fps< 32ms
• Shutter: Rolling shutter
• Iso: 100-25600
• Sensor:
  • 1/3.2″ CMOs
  • Shutter: Rolling shutter
  • Iso: 100-25600
• FOV: 150° (D);122° (H) :93° (V)
• Model: Nebula nano
• Weight: 3.5g
• Dimensions: 14 X14X21 mm
• Image ratio: 16:9
• Min.Latency: 720p 60fps < 32ms
• Sensor:
  • 1/3.2″ CMOs
  • Shutter: Rolling shutter
  • Iso: 100-25600
• FOV: 138° (D);122° (H);75° (V)
• Model: Nebula micro
• Weight: 5.8 g
• Dimensions: 19X19X20 mm
• Image ratio: 16:9
• Min.Latency: 720p 60fps < 32ms
• Sensor:
  • 1/3.2″ CMOs
  • Shutter: Rolling shutter
  • Iso: 100-25600
• FOV: 138° (D);122° (H);75° (V)

Menu board

Polar camera supports menu board adjustment, this function needs self- soldering, please be CAREFUL not to damage the camera structure during welding.

1. Remove the screws of the back cover Remove the nylon spacers.

2. Solder the menu wire and the gnd wire.
   Install the back cover. Connect the OS□ menu board .

FUNCTION

1. Left/Right button
   Control the increase or decrease of saturation.

2. Up/Down button
   Control the increase or decrease of brightness.

3. Middle button
   Short press to save, long press for 3 seconds to restore factory settings.
   Menu board needs to be purchased separately

This content is subject to change.
Down load the latest version from
https://www.caddxfpv.com/pega/download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>