Little Bo Baby T5-21A Portable Bottle Warmer Instruction Manual

Little Bo Baby T5-21A Portable Bottle Warmer Instruction Manual

IMPORTANT SAFEGUARDS

To reduce the risk of injury, and to extend the life of your product. please read and observe all information in this manual prior to and while using your product. Please save this manual for future reference

When using this appliance, basic safety precautions should always be followed, including the following:

1. Always use this warmer with adult supervision.
2. Keep this warmer out of reach of children. Children should be supervised to ensure that they do not play with the warmer.
3. Clean the warmer before first use. Clean the warmer when it has cooled down after each use. Do not lose the sealing ring when you clean the stainless-steel reservoir.
4. Do not immerse the warmer in water or any liquid.
5. Inspect the warmer before each use. Do not use the appliance if it malfunctions, or any part has become damaged.
6. Use this warmer within the ambient temperature range of so°F-95°F.
7. Do not use corrosive cleaning agents, antibacterial cleaners or high concentration detergents, otherwise plastic parts may crack.
8.  Do not place the warmer in direct sunlight or near a heat source. Do not fill the reservoir with disinfection solution for a long time, otherwise the warmer may be damaged.
9. Heating lime should not be too long. After the temperature reaches a certain temperature, the warmer will keep the breast milk warm, but the time should not exceed half an hour, because the breast milk will spoil easily if stored at a warm temperature for too long, which is dangerous for the baby’s health.
10. Always check the temperature of milk whether it is suitable or not for feeding, for example, by sprinkling a drop of milk on your wrist.
11.  The heating times provided in this instruction manual are for reference only. Actual heating time may differ due to different conditions, such as environment temperature, baby bottle material, initial milk temperature and water volume.
12.  Do not touch the stainless-steel parts during or after heating to avoid scalding.
13. Make sure to charge the battery with a power adaptor that meets the specifications. Charge the battery every three months if you do not use the warmer for an extended period of time.
14. There is built-in lithium polymer battery in the bottle warmer. Do not use the warmer in an environment with  strong static electricity or magnetic field, such as under high-voltage transmission line, or in an electrical distribution room, so as not to damage the protective device of the battery. Do not disassemble the built-in lithium polymer battery.
15.  Do not try to open or repair the warmer yourself. Improper handling or setup of this device could cause personal injury, explosion or fire.
16.  Unplug the warmer when not charging or using. After the battery is fully charged, do not continue to charge it to avoid fire or other accidents.

PARTS DESCRIPTION

1. Dust Cover (food grade silicone)
2. Reservoir (SUS316, inside the warmer)
3. Base (ABS)
4.  Digital Display
5.  Multifunctional Button (On/ Off, temperature setting, power indication)
6.  Bottom Cover (ABS)
7.  Anti-slip Pad (silicone)
8. USB Type-C Cable
9.  Charging Port/ ABS Plug

Copyright © 2022 Little Bo Baby. All rights reserved.

MULTIFUNCTIONAL BUTTON

The Multifunctional Button serves the functions of Battery Power Indication, On/Off Switch, and Temperature Setting.

• Battery Power Indication: When the warmer is turned off, press the button to display the battery power of 100% 0%, 60%, 40%, 20% or LO.
• On/Off Switch: Press and hold the button for two seconds to turn on/off the warmer.
• Temperature Setting: After the warmer is turned on, the default temperature “98” will flash 4 times on the screen before starting to heat, indicating that the warmer is heating to the default temperature of 98°F, then the real-time temperature of the milk will be displayed. Press the button to change the preset temperature in the sequence of 98°F, 104°F, 113°F, and 122°F.

HOWTOUSE

1. Clean the reservoir before using the warmer. The silicone sealing ring is already installed in the warmer reservoir.
   Be careful not to lose the silicone sealing ring during cleaning. Add milk or purified water into baby bottle.

2. Turn the warmer upside down and screw the bottle tightly onto the warmer.

3. Press and hold the multifunctional button for two seconds to turn on the warmer.

4.  Press the button to change the preset temperature in the sequence of 98°F, 104°F, 113°F, and 122°F.

5. The warmer will start to heat after the selected temperature readout flashes 4 times. When the milk is heated to the set temperature, the warmer will beep once and then
   switches to keep warm. If you need not to keep the milk warm, press the button to turn the warmer off. Turn the warmer upside down and then carefully turn the bottle to disengage it from the warmer. CAUTION: Always test the milk’s temperature before feeding. Sprinkling a drop of milk on your wrist is an effective method to test the temperature.

6.  If you do not turn the warmer off, the warmer will switch to keep warm automatically after heating is completed. Turn the warmer off after use.

Caution:

Milk should not be kept warm for too long, which is bad for your baby’s health. Milk is perishable at warm temperature. It is advisable to keep milk warm for less than half an hour.

Handy Tips:

You can heat water and keep it warm at 104°F. Whenever your baby needs milk, you can add milk powder to the ottle to get milk at the best temperature.

CHARGE THE BATTERY

• Charge the battery when power is low. When the warmer is off, press the multifunctional button to check the battery power.
• If the power is less than 20% during operation, “LO” will be displayed on the screen, reminding the user to recharge the battery. The warmer will be turned off after “LO” has flashed for 6 seconds.
• The charging port is on the back of the warmer. A USB Type-C cable is provided. Gently pull out the ABS plug and charge the battery with a power adaptor that meets the specifications (DC 5V 2Af3A). A high speed charger should not be used. After charging, fit the plug tightly to prevent moisture entering the warmer.
•  It takes about 5-6 hours to fully charge the battery. After the battery is fully charged, do not continue to charge it all day to avoid fire or other accidents.

APPLICABLE WIDE-NECK BABY BOTTLE BRANDS

Wide-neck baby bottles in the table below are compatible with this warmer. Glass bottle should be used with specified dapter. According to the different screw threads of different brands of baby bottles, we provide a silicone sealing ring, which can be inserted into the reservoir from two directions: Position “u” and Position “n”.

PLACEMENT OF SILICONE RING

The silicone ring is already placed into the warmer reservoir in “u” position. For some brands of milk bottles, the silicone sealing ring needs to be changed to “n” position.

HEATING TIME

1. If you use the warmer at home or where there is a power supply, you can use a power adapter during the heating process.
2. The heating time illustrated in the diagram is for reference only. The actual time may vary depending on environmental and other factors. Copyright© 2022 Little Bo Baby. All rights reserved.

DURATION OF KEEP WARM

The warmer can keep water warm at 104 ‘F for 12 hours when the battery is fully charged.

FREQUENTLY ASKED QUESTIONS

SPECIFICATIONS

[](https://manuals.plus/wp-content/uploads/2023/03/Little-Bo-Baby-T5-21A-

Portable-Bottle-Warmer-Instruction-Manual_7.png)DISPOSAL

When this appliance has reached the end of its life, please dispose of the unit properly.
This and other electrical appliances contain – valuable materials that can be recycled.
Electronic waste may be harmful to our environment if not disposed of properly.
We ask that you follow your governing agency’s rules and regulations when disposing of electronic appliances. Please find an authorized recycling facility near you.

CONTACT

If you have any any questions or need assistance, please contact our customer service department at cs@littlebobaby .com. Please read the operating instructions before using
Please keep the original box and packaging materials in the event that service is required.

Manufacturer’s Limited Warranty :
: This product comes with a two-year warranty from date of :
: purchase. The warranty applies only to the original buyer of :
: the product. Normal wear and tear or damage caused by :
: misuse, abuse, negligence, accident, acts of nature, or :
: unauthorized modification or repair are not covered by this :

warranty. :

The manufacturer will repair or replace with a new or : refurbished product at its option. The Manufacturer retains   the right to inspect the product, and all costs for mailing the :
: product for inspection shall be borne solely by the buye  The buyer should email us the product name and model  number, the original purchase certificate, contact informa lion, and details with pictures at cs@littlebobaby.com.

For the fastest processing of a warranty claim, the owner should e-mail cs@littlebobaby.com and include the product name and model #, proof of original purchase,
complete contact information, and detailed information about the issue, including pictures when applicable.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>