MightyJet 8500 AIO Return Pump Mini Controllable DC Owner’s Manual
- June 9, 2024
- MightyJet
Table of Contents
8500 AIO Return Pump Mini Controllable DC
Owner’s Manual
8500 AIO Return Pump Mini Controllable DC
How to Use the MightyJet Controller
PRESS: the or button to increase or decrease the flow rate of the MightyJet Pump.
PRESS AND HOLD: the button to toggle between STREAM Mode and SINE WAVE
Mode.
When the controller’s display that reads a “1” You are in STREAM Mode.
When the controller’s display that reads a “2” You are in SINE WAVE Mode.
PARTS #’s FOR 8500 | 8501| 8502
8500 Mini
1 | MightyJet Motor | 850003 |
---|---|---|
2 | MightyJet Impeller | 850005 |
3 | MightyJet Impeller Cover | 850004 |
4 | MightyJet Front Cover | 850006 |
5 | MightyJet Base | 850007 |
6 | MightyJet Fittings | 850008 |
8501 Desk Top
1 | MightyJet Motor | 850103 |
---|---|---|
2 | MightyJet Impeller | 850105 |
3 | MightyJet Impeller Cover | 850104 |
4 | MightyJet Front Cover | 850106 |
5 | MightyJet Base | 850107 |
6 | MightyJet Fittings | 850108 |
8502 Mid Size
1 | MightyJet Motor | 850203 |
---|---|---|
2 | MightyJet Impeller | 850205 |
3 | MightyJet Impeller Cover | 850204 |
4 | MightyJet Front Cover | 850206 |
5 | MightyJet Base | 850207 |
6 | MightyJet Fittings | 850208 |
WARNING
READ ALL SAFETY INSTRUCTIONS BEFORE USE.
To avoid electric shock, special care should be taken since water is employed
in the use of aquarium equipment. For each of the following situations, do not
attempt to repair yourself. Return the appliance to an authorized service
facility for service or discard the appliance.
Carefully examine the appliance after installation. It should not be plugged
in if there is water on parts not intended to be wet.
Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or if it is dropped or damaged in any manner.
To avoid the possibility of the appliance plug or receptacle getting wet,
position aquarium to one side of a wall mounted receptacle to prevent water
from dripping onto the receptacle plug. A “Drip Loop” should be arranged by
the user for EACH cord connecting an aquarium appliance to a receptacle. The
“Drip Loop” is that part of the cord below the level of the receptacle or the
connector if an extension cord is used. This “Drip Loop” prevents water
travelling along the cord and coming in contact with the receptacle. If the
plug or the receptacle do get wet DO NOT unplug the cord. Disconnect the fuse
to the circuit breaker that supplies power to the appliance. Then unplug and
examine for the presence of water in the receptacle.
Close supervision is necessary when any appliance is used by or near children.
Always unplug an appliance from the outlet when not in use, before putting on
or taking off parts, and before cleaning. Never yank the cord to pull plug
from outlet. Grasp the plug and pull to disconnect. Do not use an appliance
for other than intended use. The use of attachments not recommended or sold by
the appliance manufacturer may case an unsafe condition.
Do not install or store the appliance where it will be exposed to the weather
or to temperatures below freezing.
Make sure an appliance mounted on a tank is securely installed before
operating it.
Read and observe all the important notices on the appliance.
This appliance has a polarized plug (one blade is wider than the other). As a
safety feature, this plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Never use with an extension cord unless
plug can be fully inserted. Do not attempt to defeat this safety feature.
If an extension cord is necessary, a cord with a proper rating should be used.
MODE 1: STREAM
The Stream Mode is a calm, uninterrupted constant movement of water at a
single speed
Each Mode has 9 speed settings that can be controlled using the buttons.
1.1 Being the minimum and 1.9 being maximum speed.
After the speed has been set, a different number will show. This number is how
much wattage is currently being used. Example: 30 = 30 Watts.
FEED MODE
PRESS: the button to activate feed mode.
The display will read ‘FE’ and the pump will shut off and will automatically
resume after 10 minutes.
You can override the 10 minute timer by pressing the ‘FEED’ button again and your pump will resume.
MODE 2: SINE WAVE
The Sine Wave Mode is a smooth repetitive oscillation that moves water in a
continuous wave motion.
Each Mode has 9 speed settings that can be controlled using the buttons.
2.1 Being the minimum and 2.9 being maximum speed.
LOCKING YOUR SETTINGS
PRESS AND HOLD: the button to activate the “LOCK” function. The display will read “LC” and all buttons will be disabled.
UNLOCKING YOUR SETTINGS
PRESS AND HOLD: the button to deactivate the “LOCK” function. The display will
no longer read “LC” and all buttons will be enabled.