KOOVON ABB880 Smart Water Flosser and Toothbrush Combo User Manual

ABB880 Smart Water Flosser and Toothbrush Combo
User Manual

ABB880 Smart Water Flosser and Toothbrush Combo

Thank you for purchasing this product. To ensure proper use and trouble-free operation, please read this manual carefully and store it in a safe place for future reference.

Safety Instructions

1. Do not hold the charger with wet hands.
2. Do not place the device into water or other liquid.
3. Keep children under 8 years old away from the device. It is not suggested to a person who is suffering from physical, sensory, or mental retardation, or lack of experience and knowledge.

Warning

1. Please consult the dentist first for oral diseases.
2. Remove the transparent brace before use.
3. Do not use this product with a damaged cord, plug, or abnormal working.
4. Do not use this product if your tongue or mouth with an open wound.
5. Do not use the water flosser to rinse under the tongue, into the ear, nose, or other delicate areas.
6. Do not apply excessive pressure to the jet tip during use.
7. Do not use mouthwash/rinse that contains iodine, bleach, or tea tree oil.
8. Do not repair the product without authorization, if there is any quality problem, please contact the seller.

Product Description

Specification

Product Name: Smart Floss System
Model Number: ABB88O
Rated Voltage: DC 3.7V
Output DC 5V 1A
Charging Method: USB charging
Charging Time: 4 hours
Waterproof (Main Handle): IPX7
Water Tank Capacity: 800 ml

Charging

a. Power off the unit while charging.
b. Charge the unit 4 hours based on the battery pre-charging status for first use.
c. Charge the unit with the equipped USB cable with the power bank, PC, or other 5V 1A devices.
d. Disconnect the plug after fully charged.
Note:
a. For first use or not used for over 6 months, the charging indicator may not light up for a few minutes at the beginning of charging. in this condition, please charge the unit for 12 hours or more.
b. The unit may get warm during charge, which is normal.
C: USB adapters are not included, regular USB adapters can be used.
Indicator light status
a. Red: Charging b. Green: Fully charged c. Flashing Red: Low battery level.

Usage Guidance

Water Flossing Function – Home Use
1. Remove the water tank from the base and open the water tank cap. Then fill the tank with clean water.   2. Insert the water tank to the base.
3. Insert the water jet tip into the main handle.
4. Select the working mode.
Press the “M” button 1-2 seconds to switch from “Pulse” to H (high speed)” to “L (low speed)”.

5. Select the timing mode.
Press the “M” button 2-3 seconds to switch the timing mode.

Note: The tim ng mode will retain the previous selection of mode. When the battery is run out, the appliance may return to the default factory setting “N’: Press the “M” button for about 1.5 seconds to switch the “D” mode,
6. Press the power button to start flossing.
Note: Place the jet tip in the mouth before pressing the power button to prevent water splashing.
a. Press the “M” button to switch modes. Raise the elbow and keep the head over the basin.
b. Keep the water flow towards teeth or gums in a vertical way.
c. Move along the teeth in a slow way and clean the teeth in order.
d. Keep the jet tip rinse up and down the gums in a vertical way to clean teeth, crowns, and dentures.
7. Press the power button to power off the unit after use.
Note: Before removing the jet tip from the mouth, power off the unit to prevent water splashing.

Water Flossing Function – Travel Use

1. Take off the big water tank and base.
   

2. Unfold the water supply tube.
   

3. Insert the water supply tube into the main handle. Then put the other side of the water supply tube into a container filled with water. At last, stick the water supply tube on the container with the fixing clip.
   Note: Make sure the water supply tube reaches the bottom of the container.
   

4. Select the water pressure work mode and timing mode as “Home use” mentioned above. Then, ready to use.

Electric Toothbrush Function

1. Disconnect the suction hose from the main handle.
   

2. Take out the water jet tips. Upside down the handle and press the power button to release the remaining water.
   

3. Install toothbrush head.
   

4. Select the timing mode and toothbrush mode as the water flosser function. Then ready to use.

After Use

1. Release the remaining water inside the main handle.
   a. Press the release button .
   b. Pull out the water jet tip.
   c. Turn the main handle down and press the power button to release the remaining water.

2. Wipe dryer the charging base.

3. Put back the main handle to the base, and store them in a dryer place.

Cleaning and Maintenance

1. Gentle to scrub the top of the water supply tube with a soft brush.

2. Toothbrush head cleaning
   a. Rinse the toothbrush head down after brushing
   b. Remove it from the main handle and wipe the metal part with a dry cloth.
   Note: Do not rinse the toothbrush head after removing it from the handle to prevent damage to the toothbrush head due to water entering.  

Troubleshooting Guide

The charging
indicator does not light up.| The connection between the charging port and the USB cable is wrong.| a.Ensure the charging port and the USB cable is well connected.
b.Try another socket
The device is not
properly connected to an electrical supply.| Remove the product from the charging base, and insert it into the charger again.
The device does not operate.| For first-time use or the unit not used for more than 3 months. The unit needs charging.| Charging the unit for at least 12 hours.
Water pressure is too low or operating time very short.| The unit needs charging.| Charge the battery for at least 4 hours.
The pump is running but no water comes out of the water jet tip.| The water tank is not well connected to the base.| Insert the water tank to the base again.
The water supply tube is blocked.| Clean the water supply tube.
The jet tip is blocked or deformed.| a.Replace a new water jet tip.
b.Turn on the device, absorb the water jet tips with your mouth until water ejecting.
Water flosser function work well, but the toothbrush function do not work| The toothbrush head broken| Replace a new tooth brush head to try again.
Main handle cannot stand firmly on the base.| The suction hose on the base is against the main handle.| Rotate the suction hose port till the main handle is fixed on the base.
Water tank leaking| Suction hose did not connect the main handle well.| a.Empty the water in the water tank
b.Keep the suction hose connected to the main handle.
The toothbrush head cannot be installed| After teeth cleaning, the nozzle is removed. and the machine head remains water stains and high air pressure| You can reinstall the handle by throwing the water out of the handle head
Electric toothbrush does not work| Machine starts tooth cleaning mode function check| Press( ) again or remove the toothbrush head to install and restart again

Warranty

The product supports a one-year warranty from the date of purchase. This warranty does not apply to products which have been lost, altered, broken, or damaged by misuse or failure to follow the instruction provided with the product. Never try to repair the product by yourself. Please contact the professional and authorized center if you need repair, otherwise, the warranty will be invalid.
Contact Us
For any inquiries concerning our products, or if you want to apply for a replacement, please feel free to contact us by email: koovon.club@outlook.com

****Sea &Mew Consulting GmbH
Mittenhuber Stralle 4. 92318 Neunwkt Yuan
Li Compliance.EU@outlook.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>