Becament Solar Motion Activated Security Light Instruction Manual

Becament Solar Motion Activated Security Light

WHAT IN THE BOX

Please read these instructions thoroughly prior to installation, then store in a safe place for future reference.

SAFETY INFORMATION

• Your motion I!ght is not a toy. Keep it out of reach from small children.
• Your motion light and solar panel are both weather-resistant.
• You can mount your motion light indoors, but your solar panel must be installed outdoors to receive light from the sun.
• If using a step ladder, you may require a second person to help install the solar motion light.
• Prior to installation, lay out all components and check against the part list section in this manual.
• Never look directly into the solar motion light when illuminated.

CARE & MAINTENANCE

• From time to time, ensure the plug between the solar panel and light is securely connected.
• It is advisable to adjust the angle of the solar panel to optimize the exposure of the sun during the winter months.
• The solar panel should be cleaned with a damp cotton cloth on a regular basis. This will ensure optimal performance and battery charging. Periodically, utilize the same technique to clean the lenses of the motion lights.
• Never let any abrasive material come into contact with the solar panel.

SPECIFICATION

• Solar Panel: Amorphous Silicon
• LED: SMD2835
• Detection Range: 0-lSM
• Model: Motion Sensor Mode
• Mode2: Dim, light/Motion Sensor Mode
• Mode3: Always on Mode
• Built in 2 PCS x 3.7V 18650 3000mAh Li-ion Batteries
• Color Temperature: 5500-6500K
• Delay Time: 30/60/1205
• Cable Length: 4.SM
• Material: ABS+PC
• Detection Angle: 180°

LIGHT MODE

Motion Sensor Mode: Press the main switch button on the light body once or press the model key, light will be triggered by motion detection, 100% high brightness stay for 30s/60s/120s, the light automatically turns off when body moves out of sensor range. Dim, Light/Motion Sensor Mode: Press the main switch button on the light body twice continuous or press the mode2 key, the light illuminates automatically at dusk using an energy saving mode of 15% low brightness, when motion is detected, 100% high brightness stay for 30s/60s/120s. When movement detection ceases, the light will revert to the low-brightness energy-saving mode. Always on Mode: Press the main switch button on the light body three times continuous or press the mode3 key: 50% Mid brightness stay for 2 hours, and then auto off. TIME: Determines the duration of the light once motion is detected: 30 seconds, 60 seconds, or 120 seconds, available for mode 1/2.

PRODUCT FEATURES

• 64 high quality LEDs
• Adjustable lighting time
• Remote control
• Solar panel with 15 ft wire
• Three lighting modes

INSTALLATION

Recommended Tools: Power Drill Phillips Screwdriver

Recommended Install Height

6.5-12 feet above the ground. At such a height, adjust motion sensor’s angle by following illustrated as below, the fixture will provide a detection distance of up to 49 feet at an ambient temperature of 77 degrees Fahrenheit .

• Ensure your solar panel is placed where exposes to optimized sunlight. Be aware of objects such as trees or property overhangs that may impede the panel’ s ability to generate a charge.

Optional: Use a power drill (not included) to create the holes on your chosen mounting surface. Use 4 of the included wall plugs and screws to fasten the solar panel to the surface. Use a power drill (not included) to drill the holes on your chosen mounting surface. Place the mounting plate over the holes & use 4 of the included wall plugs and screws to fasten the mounting plate to the surface. Buckle the motion light into the mounting plate securely

SENSOR HEAD ADJUSTMENT

After installation, aim sensor head toward desired detection area and make sure sensor head ispositioned with controls facing toward the ground.
You can adjust the sensor head up and down, left to right for desired coverage area.

Note: Before using the solar security light, the solar panel needs to be connected to the light for THREE DAYS, you can also use the 3.7V 18650 battery charger with overcharge protection directly to fully charge the battery

BATTERY REPLACEMENT INSTRUCTIONS

Batteries are located in the battery housing behind the light fixture. Turn off the light prior to opening the battery housing. Remove the four screws to reveal the batteries. When replacing the batteries, observe the correct polarity and match the battery specifications with the batteries you have removed. Use rechargeable batteries only. When replacing the batteries, be sure to:

• Use rechargeable batteries only.
• Match the replacement battery specifications with the batteries that have been removed.
• Observe the correct polarity (+ and -) when installing the replacement batteries.
• Do not mix old and new batteries and Do not mix alkaline, standard(carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries.
• IMPORTANT: Dispose of the Lithium ion battery in accordance with local, state and federal regulations.

FREQUENTLY ASKED QUESTIONS

Q: Where should the solar panel be mounted?
A: Mount your solar panel in a position that will enable the most amount of light to be absorbed (refer to Step 1 on page 2). In the Northern Hemisphere this is usually south facing.

Q: Does the solar panel require direct sun to charge?
A: The solar panel can charge the internal batteries in direct and indirect light. For best results, try to optimize your solar panel’s sun exposure.

Q: Can additional or extended cable wire for the solar panel be purchased?
A: At this point there are no extensions available for the cable that connects the light to the solar panel. Any additions to the cable will void the warranty.

Q: Why does the solar motion light appear to ‘strobe’ or ,ash?
A: A rapidly ,flashing light is caused by undercharged batteries. Turn the solar motion light’s switch to the ‘OFF’ position and charge for three full sunny days to bring the batteries to full charge. After three days, return the switch to the “AUTO’ position.

Q: Will decorative or street lights have an effect on the motion sensor’s ability to operate?
A: Yes, the sensor of the solar motion light is light-sensitive. For nighttime usage, ensure no other light activates the motion sensor.

Q: What type of battery does my solar motion light require to operate?
A: Your solar motion light requires the use of 2 pcs of 3.7V 18650 lS00MAH Lithium-ion rechargeable batteries.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>