Aoli Electronic ALRC28 Bluetooth Voice Remote Control User Manual
- June 9, 2024
- Aoli Electronic
Table of Contents
Remote control manual
Product introduction
Product name：Bluetooth voice remote control
model number：ALRC28
Function：Bluetooth、IR、Voice function
Product picture
software function
1.1Pairing and mismatch
At the same time, press and hold the remote controller for“←”“VOL-”3
seconds,The remote controller lists the pairing information, enters the
pairing mode, and the flashing frequency of the red light in the pairing
process is 2Hz.
In the actual pairing process, and the pairing distance is 20 cm to 1.5
meters. If pairing is successful, the red light of the remote control stays on
for 3 seconds; if pairing fails after 30 seconds, the red dot goes out
Equipment name: ‘RC-28′ During factory test, after the test is finished, the
test software will issue a command to clear the pairing information of the
remote controller.
1.2Back connection
Keep the remote control connected with the T set at 4m for at least 1 hour
without disconnection; When there is pairing information and the Bluetooth
connection is disconnected, Press the “power key” and “pairing combination
key” to not send the back connection broadcast. Any other key sends the back
connection broadcast for 5
seconds,the back connection is successful, and the indicator flashes for 3
times.
1.3Sleep and wake up
Without any data interaction, the remote control keeps connected for 1 hour
and then enters into the state of sleep disconnection, press any key to wake
up the remote
control, if still connected, then send the corresponding key Bluetooth code
value; If you have entered the Bluetooth connection disconnect state, you will
enter the back-connect state.After successful connection,Press any key to send
the corresponding Bluetooth code value.
1.4 OTA
When the TV is turned on, the upgrade file of the remote controller is
detected. If the upgrade file exists the remote controller performs OTA
upgrade, and LED lights flash as breath lights. At this time,the remote
controller cant be used, and any buttons don’t respond.After the upgrade is
successful, the LED light stops flashing, and the remote controller can be
used normally at this time. If the upgrade fails, it will be detected and
upgraded again at the next boot. After OTA fails, the LED light stops
flashing. And the remote controller returns to the old version for normal
operation.
1.5Low voltage prompt
When the battery power is lower than 2.4V, Every time the user presses a key,
Press any key, the red light flashes for 3s, and the frequency is 1Hz.
1.6
Press “volume-“for a long time, and the remote control enters the single
carrier mode.The transmission frequency is 2440MHz the transmission time is 20
seconds,
and the power is the single carrier with the maximum power of the chip.
Release”volume-” and exit the single carrier mode.
1.7 Indicator status
| Infrared mode | Key | Keys do not light up |
|---|---|---|
| Bluetooth mod | Key | Keys do not light up |
| Pair | Pair | Red Led blinking time: 30s |
Frequency: 2Hz
Pairing succeeded| The red light is always on for 3s
Pairing failed| The red light goes out
Low voltage
state| Key| Press any red light to flash for 3s Frequency: 1Hz
1.8Multi-key does not send code
Multi-key no-code function is not required..
FCC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
* RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Ver2.0
Documents / Resources
| Aoli
Electronic ALRC28 Bluetooth Voice Remote
Control
[pdf] User Manual
B28, 2BACK-B28, 2BACKB28, ALRC28 Bluetooth Voice Remote Control, ALRC28,
Bluetooth Voice Remote Control, Voice Remote Control, Remote Control
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>