ATNEDCVH UD951B Multi-Funtion 5.1 Inch Digital Audio System User Manual

ATNEDCVH UD951B Multi-Funtion 5.1 Inch Digital Audio System

Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

FEATURES

1. Support three HDMI inputs, one Coaxial input, one Optical input, one PC-USB input, one AUX input, one USB 2.0 input, and one BT 5.0 input. You can switch different signal sources randomly via Button or Remote.
2. Support one HDMI(ARC) output, one Optical output, one Coxial output, and one 5.1 ch analog audio output of RCA, all audio output simultaneously.
3. All signal sources (H DMI/ARC/COXIAL/OPTICAL/PC-USB/AUX/USB/BT 5.0) can decode to 5.1ch output, it is an audio decoder system.
4. All signal sources (H DMI/ARC/COXIAL/OPTICAL/PC-USB/AUx/BT) but USB player can convert to COXIAL/OPTICAL output, it is a S/PDIF Switcher system.
5. HDMI resolution up to 4Kx2K@60hz, support 3D
6. Supported audio farmat:DTS, DTS-ES, AC3, WAV. FLAC. APE, HDCD, AAC wMV, MP3, M4A, etc.
7. Support 5.1 ch/2.0ch output mode, FL/FR active when 2.0ch output mode.
8. Support Button or IR remote switch the input source, and information will be displayed on LCD.
9. The BTversion is 5.0, and the distance support is 15m.
10. Supporting knob or IR adjust VOLUME, supporting 100 levels of fine-tuning.
11. The power-off memory function automatically switches to the last used signal channel, USB broadcast memory before the power-off.
12. Users can upgrade firmware when manufacturers have updated it.
13. The use of a DC 12V/1A external power adapter power supply, the wide voltage can use DC (5-19V) power supply.

SPECIFICATION

• HDMI version ——————————————— HDMI 2.0 & HDCP 2.2
• HDMI resolution ——————————————– 4Kx2K@60fs,4 Kx2K@30fs,1080p/1080i/720p/576p/576i/480 p/480i
• HDMI MAX bandwidth ——————————————– 340MHz
• HDMI MAX data rate ——————————————– 10.2Gbps
• HDMI input&output TMDS Signal ——————————————– 0.5-1.5Volts p-p(TTL)
• HDMI input&output DDC signal ——————————————– 5Volts p-p (TTL)
• HDMIinput&output transfer distance ——————————————– 20m AWG26 HDMI standard cable
• SupportAudio format-dts. DTS-es. wav, flac ape ac3. hdcd. aac. wmv. mp3, m4a etc
• DSP sample frequency range ——————————————–  24~192 KHz
• DSP Bit rate range ——————————————– 1624 Bit
• Digital input level ——————————————– 0.1-1Volts p-p
• Analog output level(1kHz@0dB) ——————————————– >1.5V RMS
• SNR OdB(CCIR/ARM) ——————————————– >90dB
• Frequency response ——————————————– .20Hz 20KHz
• Power adapter format Input ——————————————– AC100V-240V 50HZ/60Hz, DC12V/1A
• BT Version ——————————————– 5.0
• Receiving Distance of BT ——————————————– 15m
• Operating Temperature range ——————————————– -10 to +50°C
• Storage Temperature range ——————————————– -20 to +60°C
• Operating Humidity range ——————————————– 10 to 90%RH (No Condensation)
• Storage Humidity range ——————————————– 5 to 95%RH (No Condensation)
• Product/Package Dimension (Lx Wx H). ——————————————– 202x103x53 (mm)/245x192x57 (mm)
• Product/Package Weight ——————————————– 700g/950g

Panel Definition

UD951B Front Panel definition:

1. USB 2.0 port
2. IR receive port
3. LCD display panel
4. Volume knob/Input source button
5. Power button

UD951B Rear Panel definition:

1. HDMI-1 input port
2. HDMI-2 input port
3. HDMI-3 input port
4. HDMI output port with ARC
5. Optical output port
6. Coxial output port
7. DC5-19V Power input port
8. Front channels(FL/ FR)
9. Surround channels (SL/ SR)
   • A: Center channel(CEN)/Subwoofer (SW)
   • B: Coxial input port
   • C: Optical input port
   • D: PC-USB Soundcard input port
   • E: AUX input port
   • F: BT wireless antenna

UD951B LCD Definition

UD951B External Input definition:

1. Input channel name: HDMI-1/HDMI-2/HDMI-3/ARC/COXIAL/ OPTICAL/ PC-USB /AUX/ USB
2. Product model.: UD951B
3. 5.1ch: ouput5.1ch mode, 2.0ch: Output 2.0ch mode (FL/FR)

UD951B USB Player display definition:

1. Songs name and format
2. The song playing time/Song length
3. Song number/Songs quantity
4. Product model.: UD951B
5. 5.1ch: 5.1 channels output mode; 2.0ch: 2.0 channels output mode (only FL/FR output)
6. :Repeat all; :Repeat one

Remote Controler Definition

Contents In The Box

1. UD951B Digital System x1
2. Infrared remote controller
3. DC-12V/1A power adapter x1
4. Digital optical fiber cable x1
5. User manual x1
6. BT wireless antenna x1

Operation Guide

1. Connecting all signal wires before power on, LCD will be turned on and information will be displayed after starting about 15s, then you can do the operation
2. Button operating functions: POWER: Power button, it will turn off machine power. (PS: The red key of Remote only Standby, it will not turn off the power.) SWITCH/VOLUME: Press to switch the input source, Turn the volume up clockwise, and turn the volume down against the clock.
3. Remote control refers to the “Remote Controler Definition”.
4. HDMI output corresponds to HDMI inputs, LCD display corresponds to USB-disc player, and USB-disc player can not display to HDMI output.
5. 5.1ch and 2.0ch selection:
   • 5.1CH mode: Output as 5.1CH mode
   • 2.0CH mode: Output as 2.0CH mode(only FL/FR output)
6. Audio output instructions:
   • A. Output from COX/OPT: All inputs but the USB-disc player can switch to COX/OPT output.
   • B. Output from 5.1ch: All inputs are decoded to 5.1ch output.
7. ARC function skills:
   • A. Set the HDTV or Projector to an external speaker, and audio output format select” RAW”.
   • B. HDMI cable must be 19+1 pins.
   • C. Select ARC mode on the UD951B.
8. BT wireless skills:
   • A. UD951B must be set as BT 5.0 mode
   • B. Turn on the BT of your mobile device, and search the BT name: “UD9518”
   • C. Click the “UD951B” to connect it and play music.

References

• ATNEDCVH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>