IMERE G14000352 Kids Learning Table Installation Guide

IMERE G14000352 Kids Learning Table Installation

KID’S LEARNING TABLE INSTALL MANUAL

Please read the product instructions carefully before assembling and using, and keep it properly for future reference.
We are very happy if you are happy with your shopping experience.
Here we offer some suggestions for you to express your happy feelings.

1. Tell your family or friends
2. Share your experience by writing a review on Amazon
   We are very sad if you are not happy with your shopping experience. But don’t worry, we will try ourbest to make you happy again. Here we offer some suggestions for you to contact us.

SAFETY USE

1. Recommend checking the screws and bolts several times a year to ensure they stay tight.
2. Max Load capacity for desk is 66 Ibs, chair is 198 Ibs.
3. Please don’t make them overloaded.
4. In door use only. Suitable temperature 18-28 degrees and humidity 40%-60%.
5. Avoid direct sunlight burning and plcing next to radiator to prevent desktop aging or discoloration.
6. For all surfaces: wipe clean with a damp cloth and a weak cleaning solution, and then dry with a clean and dry cloth. Please loosen the knob when lifting, adjust to the required height and then tighten the knob.(No need to tighten excessively)

Table Installation Steps

1. Take out the desktop. And then remove the screws on both sides of the table with a screwdriver.
2. Fit the table legs and the desktop together, and install the screws with a screwdriver. (TIPS: The side with height and gear reference table faces Out.)
3. Remove the screws of table leg with a screwdriver. And then fit the table-leg connector with the table legs together, and install the screws with a screwdriver.
4. Put the table properly in the right position then adjust the hinge screws under the feet so that it can be placed on the ground smoothly.
5. Install the reading rack and bag hook on the table.

Warning

1. Check thne status of all screws and tighten them one by one after all screws are installed.
2. Do not tighten the knob completely when the table or chair are not installed, which may cause Iifting dysfunction.
3. Pav attention! Only adults are allowed to install, children are required to be accompanied by a parent while installation.
4. when both sides of chair or table are adjusted and fixed to your desire height, there are click sounds in both sides. It can be reset by liting up trom the highest gear.

Chair Installation Steps

1. Take out the seat back and the chair leg. (TIPS: The side with height and gear reference table faces out.)
2. Install the seat back by the screwdriver on the back of the chair with the screws (the short flat head screws in the installation package).
3. Place the seat on the chair legs and align it with the chair legs.
4. Turn the seat and legs over together and install the screws (the longer flat head screws in the installation pack) with a screwdriver.
5. Remove the screws of chair leg with a screwdriver. And then take out the chair-leg connector, fit it with the chair legs together, and install the screws with a screwdriver.
6. Put the chair properly in the right position then adjust the hinge screws under the feet so that it can be placed on the ground smoothly. Check the status of all screws and tig hten all screws.

Warning:

1. Check the status of all screws and tighten them one by one after all screws are installed. (Attentions: Do not tighten the knob completely when the table Care not istded, WayCuse ng aysiucuon.
2. Do not drill into the bottom of the table or chair.
3. Pay attention Only adults are allowed to install, children are required to be accompanied by a parent while installation.
4. When both sides of chair or table are adjusted and fixed to your desire height, there are click sounds in both sides. It can be reset by lifting up from the highest gear.

Demonstration of Height Adjustment

Warning

1. Lift up: When you pull and drop the table or chair, please note th strength on both sides should be equally. Pull and drop balanced, and the two sides need to keep consistent. Lift up the gear one by one to the required height (the lifting speed needs to be slower), and you can hear the click sound on both sides.
2. Go down: Adjust to the highest position and let go. It slowly drops to lowest automatically. Click sound means it can readjust to required height.

Description of Packaging Parts

Before installation, please check that the accessories you receive are complete, so as to complete the installation faster and more accurately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>